How to Install a Harmonic Balancer and Complete the Necessary Steps on 2010 Dodge Challenger?

Add the Forcing Screw C-4685-C1 with Nut and Thrust Bearing from Crank Sprocket Installer 6792 when putting in the crankshaft harmonic balancer. After that, insert the crankshaft harmonic balancer bolt and use the Damper Holding Fixture 9365 to tighten it to 95 Nm. Next, put on the accessory drive belt. Put the radiator cooling fan assembly into the car and attach the bolts for the fan, tightening them to 6 Nm. In place the fan electrical connector and tie the upper radiator hose into position. Attach the negative battery cable to its spot, then tighten the nut with 5 Nm of force. After filling the engine's cooling system, start it and allow it to get to its normal operating temperature while you check and add fluid if necessary.

OEM 2010 Dodge Challenger Harmonic Balancer

Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Harmonic Balancers found

View related parts
2010 Dodge Challenger Vibration Damper Part Number: 5037394AA
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
- Item Weight: 7.40 Pounds
- Item Dimensions: 10.8 x 10.5 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5037394AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- SRT8 | 8 Cyl 6.1 L GAS
View related parts
2010 Dodge Challenger Vibration Damper Part Number: 53022412AA
Product Specifications
- Other Name: Damper - Vibration; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Vibration
- Replaces: 53022084AA
- Item Weight: 8.80 Pounds
- Item Dimensions: 9.2 x 9.2 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53022412AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- R/T | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
2010 Dodge Challenger Vibration Damper Part Number: 4792811AB
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
- Item Weight: 5.40 Pounds
- Item Dimensions: 9.2 x 8.3 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792811AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- SE | 6 Cyl 3.5 L GAS

2010 Dodge Challenger Harmonic Balancer Parts and Q&A

Q: How to Install a Harmonic Balancer and Complete the Necessary Steps on 2010 Dodge Challenger?
A: Add the Forcing Screw C-4685-C1 with Nut and Thrust Bearing from Crank Sprocket Installer 6792 when putting in the crankshaft harmonic balancer. After that, insert the crankshaft harmonic balancer bolt and use the Damper Holding Fixture 9365 to tighten it to 95 Nm. Next, put on the accessory drive belt. Put the radiator cooling fan assembly into the car and attach the bolts for the fan, tightening them to 6 Nm. In place the fan electrical connector and tie the upper radiator hose into position. Attach the negative battery cable to its spot, then tighten the nut with 5 Nm of force. After filling the engine's cooling system, start it and allow it to get to its normal operating temperature while you check and add fluid if necessary.