How to Service and Repair an Upper Intake Manifold on 2010 Dodge Challenger?

For upper intake manifold service, you should first clean and check the gasket sealing areas and then lay the new gasket into place. Place the foam onto the upper intake manifold first, then connect the manifold, using a 12 Nm (105 in. lbs.) crisscross sequence starting from the center. After that, attach the needed manifold support brackets and set all of the fasteners to 12 Nm (105 in. lbs.). After connecting the short runner valve electrical connector, add the throttle bracket and tighten each fastener to 12 Nm (105 in. lbs.) at the throttle body and 28 Nm (259 in. lbs.) at the cylinder head. Engage the connector of your harness with the electronic throttle control and attach the PCV hose, power brake vacuum hose and purge hose to the intake manifold. Put in the EGR tube, strut tower support, wiper module and cowl panel. Join the Manifold Absolute Pressure (MAP) sensor to its connector, add the inlet hose and connect the Inlet Air Temperature (IAT) sensor harness connector. After that, link the negative cable to the battery and tighten the nut to 5 Nm (45 in. lbs.).

OEM 2010 Dodge Challenger Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Intake Manifolds found

View related parts
2010 Dodge Challenger Intake Plenum, Upper Part Number: 4591863AM
$1121.58 MSRP: $1705.00
You Save: $583.42 (35%)
ADD TO CART
Product Specifications
- Other Name: Plenum - Intake Manifold; Engine Intake Manifold, Upper; Plenum; Plenum Intake Manifold; Intake Manifold
- Position: Upper
- Replaces: 4591863AL
- Item Weight: 22.20 Pounds
- Item Dimensions: 35.0 x 29.1 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4591863AM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- SE | 6 Cyl 3.5 L GAS
View related parts
2010 Dodge Challenger Intake Manifold, Lower Part Number: 4792184AH
$387.01 MSRP: $569.00
You Save: $181.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Intake; Engine Intake Manifold, Lower, Upper
- Position: Lower
- Item Weight: 7.30 Pounds
- Item Dimensions: 23.7 x 7.3 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792184AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- SE | 6 Cyl 3.5 L GAS
View related parts
2010 Dodge Challenger Intake Manifold Part Number: 68048131AC
$367.55 MSRP: $537.00
You Save: $169.45 (32%)
Product Specifications
- Other Name: Manifold - Engine Intake; Engine Intake Manifold; Manifold Kit Engine Intake
- Replaces: 68048131AA, 68048131AB
- Item Weight: 21.60 Pounds
- Item Dimensions: 24.1 x 22.7 x 11.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68048131AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- R/T, R/T Classic | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
2010 Dodge Challenger Intake Manifold Part Number: 5037510AK
Product Specifications
- Other Name: Manifold - Intake; Engine Intake Manifold
- Replaces: 5037510AJ, 5037510AH, 5037510AG, 5037510AI
- Item Weight: 36.80 Pounds
- Item Dimensions: 25.5 x 18.0 x 8.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5037510AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2010 Dodge Challenger Submodels:
- SRT8 | 6.1L V8, 8 Cyl 6.1 L GAS

2010 Dodge Challenger Intake Manifold Parts and Q&A

Q: How to Service and Repair an Upper Intake Manifold on 2010 Dodge Challenger?
A: For upper intake manifold service, you should first clean and check the gasket sealing areas and then lay the new gasket into place. Place the foam onto the upper intake manifold first, then connect the manifold, using a 12 Nm (105 in. lbs.) crisscross sequence starting from the center. After that, attach the needed manifold support brackets and set all of the fasteners to 12 Nm (105 in. lbs.). After connecting the short runner valve electrical connector, add the throttle bracket and tighten each fastener to 12 Nm (105 in. lbs.) at the throttle body and 28 Nm (259 in. lbs.) at the cylinder head. Engage the connector of your harness with the electronic throttle control and attach the PCV hose, power brake vacuum hose and purge hose to the intake manifold. Put in the EGR tube, strut tower support, wiper module and cowl panel. Join the Manifold Absolute Pressure (MAP) sensor to its connector, add the inlet hose and connect the Inlet Air Temperature (IAT) sensor harness connector. After that, link the negative cable to the battery and tighten the nut to 5 Nm (45 in. lbs.).