How to Safely Service the Air Bag Control Module on Chrysler Aspen?

The first step in servicing the Air Bag Control Module is to turn off the rest of the belt system by pulling the negative terminal from the battery and wait two minutes to give the capacitor time to discharge. Ensuring you don't strike or drop the occupant restraint controller is important, as it could break the impact sensor and make you change the whole module. Lift the center console from its place at the top of the floor panel transmission tunnel. Then, let go of both locking tabs on the Occupant Restraint Controller connector receptacles and lift the levers on the two sets of body wire harness connectors. After that, remove the three screws holding the ORC to the ORC bracket welded above the floor panel transmission tunnel and then extract the ORC.

How is the Air Bag Control Module Installed on Chrysler Aspen?

You should first disconnect the battery negative cable, unplug the system and wait so the capacitor can drain for two minutes before installing the Air Bag Control Module. Apply the ORC to the ORC bracket on the floor panel transmission tunnel with the arrow on the ORC forward and the pin on the right mount positioning firmly into lock with the bracket. Put three screws into the ORC, making sure they slowly tighten to 11 Nm (8 ft. lbs.), as indicated on the screwdriver's marker. Be sure to open the harness connector latches and only then align the two body connectors into the ORC so the latches are aligned and locked. After installing the center console, do not resume using the battery negative cable until after you finish the supplemental restraint system test following any service done on a restraint system part.

OEM Chrysler Aspen Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Air Bag Control Modules found

View related parts
Chrysler Aspen Control Module Part Number: 68019613AA
$182.17 MSRP: $425.00
You Save: $242.83 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit
- Replaces: 4606948AE, 4606948AD, 4606948AC, 4606948AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Aspen | Limited | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Control Module Part Number: 4896158AF
$343.66 MSRP: $524.00
You Save: $180.34 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit
- Replaces: 4896158AA, 4896158AC, 4896158AE, 4896158AD, 4896158AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chrysler Aspen | Limited | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Control Module Part Number: 56043319AI
$102.36 MSRP: $153.00
You Save: $50.64 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 56043319AH, 56043319AG, 56043319AJ, 56043319AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chrysler Aspen | Limited | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Control Module Part Number: 56054994AE
$233.40 MSRP: $346.00
You Save: $112.60 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit
- Replaces: 56054994AC, 56054994AD, 56054994AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Aspen | Limited, Limited Hybrid | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Control Module, Passenger Side Part Number: 56043195BD
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module, Right; Occupant Module; Module Occupant Classification
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

Chrysler Aspen Air Bag Control Module

Choose OEM Air Bag Control Module that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Air Bag Control Module follows strict manufacturing steps to lock in quality and fit. If your Chrysler Aspen matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Aspen parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Chrysler Aspen Air Bag Control Module Parts and Q&A

Control Module, Passenger Side
56043195BD
Q:
How to Safely Service the Air Bag Control Module on Chrysler Aspen?
A:
The first step in servicing the Air Bag Control Module is to turn off the rest of the belt system by pulling the negative terminal from the battery and wait two minutes to give the capacitor time to discharge. Ensuring you don't strike or drop the occupant restraint controller is important, as it could break the impact sensor and make you change the whole module. Lift the Center Console from its place at the top of the floor panel transmission tunnel. Then, let go of both locking tabs on the Occupant Restraint Controller connector receptacles and lift the levers on the two sets of body wire harness connectors. After that, remove the three screws holding the ORC to the ORC bracket welded above the floor panel transmission tunnel and then extract the ORC.
Control Module
4896158AF
Q:
How is the Air Bag Control Module Installed on Chrysler Aspen?
A:
You should first disconnect the battery negative cable, unplug the system and wait so the capacitor can drain for two minutes before installing the Air Bag Control Module. Apply the ORC to the ORC bracket on the floor panel transmission tunnel with the arrow on the ORC forward and the pin on the right mount positioning firmly into lock with the bracket. Put three screws into the ORC, making sure they slowly tighten to 11 Nm (8 ft. lbs.), as indicated on the screwdriver's marker. Be sure to open the harness connector latches and only then align the two body connectors into the ORC so the latches are aligned and locked. After installing the Center Console, do not resume using the battery negative cable until after you finish the supplemental restraint system test following any service done on a restraint system part.