How to remove and install the crankshaft pulley in 3.6L V6 engine on Chrysler Sebring?

To remove the crankshaft pulley, first disconnect the negative battery cable from the remote ground terminal or battery. Loosen the lug nuts on the right front wheel, raise the vehicle, and support it securely on jackstands before removing the right front wheel. Next, remove the drivebelt. The crankshaft pulley bolt is incredibly tight; using a breaker bar, socket, and special tool #10198 or equivalent, hold the balancer to prevent it from turning while loosening and removing the bolt. Pull the crankshaft pulley off the crankshaft without needing a puller. For installation, apply clean engine oil or multi-purpose grease to the seal contact surface of the balancer hub to prevent damage to the seal lip and oil leakage. Install the crankshaft pulley, aligning the keyway on the crankshaft with the slot in the pulley hub, and install the bolt, tightening it by hand. Prevent the engine from rotating and then tighten the bolt to the specified torque. The remainder of the installation follows the reverse order of removal.

How to disconnect the negative battery cable and remove the crankshaft pulley in 2.7L V6 engine on Chrysler 200?

Disconnect the negative battery cable from the remote ground terminal. Loosen the lug nuts on the right front wheel, raise the front of the vehicle, and support it securely on jackstands. Remove the right front wheel and inner fender liner. Remove the drivebelts. Use a strap wrench around the crankshaft pulley to hold it while using a breaker bar and socket to remove the crankshaft pulley center bolt; a chain-type wrench may be used if an old drivebelt or rag is wrapped around the crankshaft pulley first. Insert special tool #8194 into the center of the crankshaft where the bolt was, then pull the damper off the crankshaft with a puller, ensuring the puller is pressing against the special tool or bolt. The jaws of the puller must only contact the hub of the pulley, not the outer ring. The crankshaft pulley covers the end of the crankshaft, so a special pin #8194 or a long Allen-head bolt should be inserted into the crankshaft nose for the puller's tapered tip to push against to prevent damage to the crankshaft pulley. Check the surface on the pulley hub that the oil seal rides on; if it has been grooved from long-time contact with the seal, a press-on sleeve may be available to renew the sealing surface, which can be pressed into place with a hammer and a block of wood. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley using a vibration damper installation tool to press it onto the crankshaft. Install the crankshaft pulley retaining bolt and tighten it to the specified torque. The remainder of installation follows the reverse order of removal.

OEM Chrysler Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Crankshaft Pulleys found

View related parts
Chrysler Vibration Damper Part Number: 4792815AA
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- 300 | 2005 | C | 8 Cyl 5.7 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: MD143435
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crank Pulley; Damper Pulley; Pulley; Pulley, Crankshaft - Alternator Drive; Pulley Drive
Fits the following Chrysler Models:
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.0 L GAS
- LeBaron | 1991-1995 | Base, GTC, LE, LX, Landau | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Voyager | 2000 | Base | 6 Cyl 3.0 L GAS
View More
View related parts
Chrysler Damper Pulley Part Number: MD319994
Product Specifications
- Other Name: Pulley - Crankshaft Air Compressor D; Pulley, Crankshaft - Power Steering And Air Condition Drive; Pulley Crankshaft
Fits the following Chrysler Models:
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.0 L GAS
- Voyager | 2000 | Base | 6 Cyl 3.0 L GAS
View related parts
Chrysler Vibration Damper Part Number: 4792815AB
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- 300 | 2006-2008 | C | 8 Cyl 5.7 L GAS
View related parts
Chrysler Vibration Damper Part Number: 53021303AA
Product Specifications
- Other Name: Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Damper Crankshaft
Fits the following Chrysler Models:
- Aspen | 2008 | Limited | 8 Cyl 5.7 L GAS
View related parts
Chrysler Vibration Damper Part Number: 5037394AA
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- 300 | 2005-2010 | C SRT8 | 8 Cyl 6.1 L GAS
View related parts
Chrysler Crankshaft Damper Part Number: 4892271AA
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- Pacifica | 2007 | Base, Limited, Touring | 6 Cyl 4.0 L GAS
View related parts
Chrysler Harmonic Balancer Part Number: 4448886
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Crankshaft Pulley; Crank Pulley; Vibration Damper; Crankshaft Damper; Damper Crankshaft; Damper, Vibration
Fits the following Chrysler Models:
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
- Imperial | 1990-1993 | Base | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- New Yorker | 1990-1993 | Fifth Avenue, Landau, Salon | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Town & Country | 1990-2007 | Base, EL, EX, LX, LXi, Limited, SX, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2000-2003 | Base, LX, SE | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View More
View related parts
Chrysler Vibration Damper Part Number: 53022412AA
Product Specifications
- Other Name: Damper - Vibration; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Vibration
- Replaces: 53022084AA
Fits the following Chrysler Models:
- 300 | 2009-2010 | C, S | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Chrysler Vibration Damper Part Number: 53020689AB
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- Aspen | 2007 | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Vibration Damper Part Number: 4792811AB
Product Specifications
- Other Name: Damper - Crankshaft; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- 300 | 2005-2010 | Limited, S, Signature Series, Touring | 6 Cyl 3.5 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: 4892135AA
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Crankshaft Damper; Damper; Damper Crankshaft
Fits the following Chrysler Models:
- Pacifica | 2007-2008 | Base, LX, Limited, Touring | 6 Cyl 4.0 L GAS
- Sebring | 2007-2010 | Limited | 6 Cyl 3.5 L GAS
- Town & Country | 2008-2010 | Limited, Touring, Touring Plus | 6 Cyl 4.0 L GAS
View More
View related parts
Chrysler Crankshaft Pulley Part Number: 4667772
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Pulley; Damper, Crankshaft Vibration; Damper Crankshaft
Fits the following Chrysler Models:
- Sebring | 1995-1999 | LX | 4 Cyl 2.0 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: 4483413
Product Specifications
- Other Name: Pulley - V - Belt Drive; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Damper; Pulley; Pulley, Drive
Fits the following Chrysler Models:
- LeBaron | 1988-1993 | Base, GT, GTC, GTS, High Line, LE, LX, Landau, Premium | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- New Yorker | 1988 | Turbo | 4 Cyl 2.2 L GAS
- TC Maserati | 1990 | Base | 4 Cyl 2.2 L GAS
- Town & Country | 1988 | Base | 4 Cyl 2.2 L GAS
View More
View related parts
Chrysler Idler Pulley Part Number: 3870074
Product Specifications
- Other Name: Pulley Assembly Drive; Serpentine Belt Drive Kit; Harmonic Balancer Puller; Harmonic Balancer; Crankshaft Pulley; Pulley; Pulley, Main Drive; Pulley, Drive
Fits the following Chrysler Models:
- Fifth Avenue | 1985-1989 | Base | 8 Cyl 5.2 L GAS
View related parts
Chrysler Vibration Damper Part Number: 4173443
Product Specifications
- Other Name: Damper; Harmonic Balancer; Damper, Crankshaft Vibration, W/318 Engine; Damper, Crankshaft Vibration; Damper, Vibration
Fits the following Chrysler Models:
- Fifth Avenue | 1984-1989 | Base | 8 Cyl 5.2 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: 4648941AA
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Damper Crankshaft
Fits the following Chrysler Models:
- Pacifica | 2005-2008 | Base, LX | 6 Cyl 3.8 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: 4663175
Product Specifications
- Other Name: Damper - Crankshaft Vibration; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Damper, Crankshaft Vibration; Damper Crankshaft; Damper, Vibration
Fits the following Chrysler Models:
- Concorde | 1993-1996 | Base, LX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Crankshaft Pulley Part Number: 4663176
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Vibration Damper; Pulley; Damper Crankshaft; Damper, Vibration
Fits the following Chrysler Models:
- 300M | 1999-2004 | Base, Pro-Am, Special | 6 Cyl 3.5 L GAS
- Concorde | 1993-2004 | Base, LX, LXi, Limited | 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
- LHS | 1999-2001, 1994-1997 | Base | 6 Cyl 3.5 L GAS
- New Yorker | 1994-1996 | Base | 6 Cyl 3.5 L GAS
- Prowler | 2001-2002 | Base | 6 Cyl 3.5 L GAS
View More
View related parts
Chrysler Crankshaft Pulley Part Number: 4792430AA
Product Specifications
- Other Name: Damper - Crankshaft; Engine Crankshaft Pulley; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Pulley; Damper Crankshaft
Fits the following Chrysler Models:
- Concorde | 1998-2004 | LX | 6 Cyl 2.7 L GAS

| Page 1 of 3 |Next >

1-20 of 42 Results

Chrysler Crankshaft Pulley

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Crankshaft Pulley for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Crankshaft Pulley maintains the belt-driven systems in order and reduces engine vibration to allow smoother daily driving. Since 1925, Chrysler has had solid build quality, price sanity, and allowed families to purchase roomy sedans without starving economies and with less noise in the cabin courtesy of the pioneering Floating Power mount system. Chrysler would later introduce the Airflow, which demonstrated that aerodynamic acumen could be carried with fearless styling and enhanced comfort over drab conservative design that was neither as road-feel as theirs. In the case where utility was required, Chrysler provided the first useful minivan, opening sliding cargo doors that fit the contents of a weekend trip and clutter of kid pandemonium without distending the outside footprint or choking fuel economy numbers. Decade after decade, Chrysler fine-tuned ride quality, made interior space broader, and the purchasing process easy so customers felt that the brand respected their wallet and time. The Crankshaft Pulley is attached to the nose of the crank, clamped to a serpentine belt, and turns the alternator, A/C compressor, and power steering pump in flawless time with each stroke of the piston. The rubber damping absorbs the torsional vibrations, thus the dashboard remains smooth and components remain intact. Material modifications allow the Crankshaft Pulley to lose weight without compromising strength, enabling an engine to rev faster without compromising reliability. The Crankshaft Pulley dimension and the commonality across generations mean that it is easy and the whole powertrain can be cooperative with the replacements swapped in by the owners.

Chrysler Crankshaft Pulley Parts and Q&A

Crankshaft Pulley
4892096AA
Q: How to remove and install the crankshaft pulley in 3.6L V6 engine on Chrysler Sebring?
A:
To remove the crankshaft pulley, first disconnect the negative battery cable from the remote ground terminal or battery. Loosen the lug nuts on the right front wheel, raise the vehicle, and support it securely on jackstands before removing the right front wheel. Next, remove the drivebelt. The crankshaft pulley bolt is incredibly tight; using a breaker bar, socket, and special tool #10198 or equivalent, hold the balancer to prevent it from turning while loosening and removing the bolt. Pull the crankshaft pulley off the crankshaft without needing a puller. For installation, apply clean engine oil or multi-purpose grease to the seal contact surface of the balancer hub to prevent damage to the seal lip and oil leakage. Install the crankshaft pulley, aligning the keyway on the crankshaft with the slot in the pulley hub, and install the bolt, tightening it by hand. Prevent the engine from rotating and then tighten the bolt to the specified torque. The remainder of the installation follows the reverse order of removal.
Crankshaft Pulley
5184293AH
Q: How to disconnect the negative battery cable and remove the crankshaft pulley in 2.7L V6 engine on Chrysler 200?
A:
Disconnect the negative battery cable from the remote ground terminal. Loosen the lug nuts on the right front wheel, raise the front of the vehicle, and support it securely on jackstands. Remove the right front wheel and inner fender liner. Remove the drivebelts. Use a strap wrench around the crankshaft pulley to hold it while using a breaker bar and socket to remove the crankshaft pulley center bolt; a chain-type wrench may be used if an old drivebelt or rag is wrapped around the crankshaft pulley first. Insert special tool #8194 into the center of the crankshaft where the bolt was, then pull the damper off the crankshaft with a puller, ensuring the puller is pressing against the special tool or bolt. The jaws of the puller must only contact the hub of the pulley, not the outer ring. The crankshaft pulley covers the end of the crankshaft, so a special pin #8194 or a long Allen-head bolt should be inserted into the crankshaft nose for the puller's tapered tip to push against to prevent damage to the crankshaft pulley. Check the surface on the pulley hub that the oil seal rides on; if it has been grooved from long-time contact with the seal, a press-on sleeve may be available to renew the sealing surface, which can be pressed into place with a hammer and a block of wood. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley using a vibration damper installation tool to press it onto the crankshaft. Install the crankshaft pulley retaining bolt and tighten it to the specified torque. The remainder of installation follows the reverse order of removal.