How to Install a Brake Caliper on the Rear on Chrysler Sebring?

First, pull the piston into the housing all the way using a C-clamp and a block of wood covering it. After that, press the new brake pad onto the caliper and ensure the retaining clip snaps into place beyond the raised bead and into one of the small slots on the caliper. Carefully fit the brake caliper onto the adapter bracket with its outboard pad resting over the inboard pad and rotor and make sure not to harm the guide pin boots. At installation, remember that the special sleeve is used with the upper mounting hole for the caliper guide pin bolt. First, get the caliper guide pin bolt holes to line up with the adapter bracket, then screw in the lower and upper guide pin bolts until tightened to 43 Nm (32 ft. lbs.). Insert the rear brake flex hose into the brake caliper and tighten the clamp to 15 Nm (133 in. lbs.). Loop the brake flex hose under the trailing link mounted bracket and fix it in place with the clip. Slide the brake tube nut inside the brake flex hose and torque it firmly to 20 Nm (177 in. lbs.). Attach the wheel and tire set, tightening the wheel nuts to 135 Nm (100 ft. lbs.) and when the vehicle is down, remove the brake pedal holding tool. Repeat the bleeding process if required and drive down the road several times to burn off any new residue on your brakes and get your shoes to grip properly.

How to Remove and Replace a Brake Caliper on Chrysler Sebring?

In order to take off and assemble the brake caliper, under the safety precaution, the brake pedal holding tool should depress the brake pedal more than one inch (25 mm) of the travel isolated the master cylinder of the brake hydraulic system, and block the brake fluid leakage. Then lift and prop the car, after that take the three wheel mounting nuts and dismount the tire and wheel assembly. Unscrew the banjo bolt which holds the brake flex hose to the brake caliper throwing away the two washers, which drop off with bolt. In taking out the two brake caliper guide pin bolts, one of them (upper) has a special sleeve that the end of the bolt, and this should be fitted in upper mounting hole when replacing the bolts. The last step is laying off the disc brake caliper that goes through the disc brake adapter bracket and brake pads.

OEM Chrysler Sebring Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Brake Calipers found

View related parts
Chrysler Sebring Caliper, Rear Passenger Side Part Number: 5191268AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Caliper, Front Driver Side Part Number: 5191239AA
$113.04 MSRP: $171.00
You Save: $57.96 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Caliper, Rear Passenger Side Part Number: 5019743AB
$89.99 MSRP: $159.00
You Save: $69.01 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left, Rear Right; Brake Caliper
- Position: Rear Passenger Side
- Replaces: 5019743AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, LX, LXi, Limited, TSi, Touring | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper, Rear Driver Side Part Number: 5191267AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Caliper, Front Passenger Side Part Number: 5191238AA
$130.02 MSRP: $181.00
You Save: $50.98 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Caliper, Front Passenger Side Part Number: MR527671
$49.02 MSRP: $62.15
You Save: $13.13 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc Brake Caliper, Front Right; Caliper Disc Brake Right; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Sebring | LX, LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper Part Number: MB928410
Product Specifications
- Other Name: Caliper Package, Front Left; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chrysler Sebring | JX, JXi, LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Caliper, Front Passenger Side Part Number: MR449856
Product Specifications
- Other Name: Caliper K - Front Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake Right; Caliper Kit Front Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4 L GAS
View related parts
Chrysler Sebring Caliper, Front Driver Side Part Number: MR449855
Product Specifications
- Other Name: Caliper K - Front Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake Left; Caliper Kit Front Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4 L GAS
View related parts
Chrysler Sebring Caliper, Rear Passenger Side Part Number: MR129584
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Package, Rear Brake; Caliper Disc Brake
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chrysler Sebring | Base, GTC, JX, JXi, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper Assembly, Rear Driver Side Part Number: MR129583
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper; Caliper Package, Rear Brake; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chrysler Sebring | Base, GTC, JX, JXi, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper Part Number: MB928411
Product Specifications
- Other Name: Brake Caliper; Caliper Package, Front Right; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chrysler Sebring | JX, JXi, LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Caliper, Front Passenger Side Part Number: 5018990AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper Assembly Part Number: 5011701AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Caliper Assembly Part Number: 5011700AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Caliper Assembly Part Number: 4856922
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Assembly, Front Wheel Disc Brake Partial, Right; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Caliper Assembly Part Number: 4856923
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Assembly, Front Wheel Disc Brake Partial, Right; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Steering Column, Front Passenger Side Part Number: 5083790AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly; Caliper; Caliper Disc Brake
- Position: Front Passenger Side
- Replaces: 5072544AA, 5019520AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chrysler Sebring | Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Sebring Caliper, Front Driver Side Part Number: 5072551AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Caliper, Front Passenger Side Part Number: 4605A018
Product Specifications
- Other Name: Caliper - Front Brake; Disc Brake Caliper, Front Left, Front Right; Caliper Kit Front Brake; Brake Caliper
- Position: Front Passenger Side
- Replaces: MN102869
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chrysler Sebring | LXi, Limited | 3.0L V6, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Chrysler Sebring Brake Caliper

Choose OEM Brake Caliper that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Caliper follows strict manufacturing steps to lock in quality and fit. If your Chrysler Sebring matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sebring parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Brake Caliper in Chrysler Sebring involves usage in converting hydraulic pressures, coming from a master cylinder to the sort of mechanical force that will bring the brake pads into contact with the rotors for slowing or stopping the cars. Chrysler Sebring models utilize two primary types of brake calipers: tertiary and non tertiary There are two types of interchange known as fixed and floating. Fixed calipers have several pistons on the either side of the rotor with equal force and floating calipers have pistons only on one side and slides across the rotor for applying pressure which may cause such problems as uneven wear of the pads if not attended to. The calipers are mostly produced from cast iron depending on the variety and the pistons from steel or phenolic kinds. Options are available in the form of performance parts that include better calipers than those factory-fitted, with benefits such as better braking ability and better looks. The maintenance of the brake calipers should be done periodically to avoid incidences of a sinking of the brake pedal or dragging of brakes which are major problems.

Chrysler Sebring Brake Caliper Parts and Q&A

Caliper, Rear Driver Side
5191267AA
Q: How to Install a Brake Caliper on the Rear on Chrysler Sebring?
A:
First, pull the piston into the housing all the way using a C-clamp and a block of wood covering it. After that, press the new Brake Pad onto the caliper and ensure the retaining clip snaps into place beyond the raised bead and into one of the small slots on the caliper. Carefully fit the brake caliper onto the adapter bracket with its outboard pad resting over the inboard pad and rotor and make sure not to harm the guide pin boots. At installation, remember that the special sleeve is used with the upper mounting hole for the caliper guide pin bolt. First, get the caliper guide pin bolt holes to line up with the adapter bracket, then screw in the lower and upper guide pin bolts until tightened to 43 Nm (32 ft. lbs.). Insert the rear brake flex hose into the brake caliper and tighten the clamp to 15 Nm (133 in. lbs.). Loop the brake flex hose under the trailing link mounted bracket and fix it in place with the clip. Slide the brake tube nut inside the brake flex hose and torque it firmly to 20 Nm (177 in. lbs.). Attach the wheel and tire set, tightening the wheel nuts to 135 Nm (100 ft. lbs.) and when the vehicle is down, remove the brake pedal holding tool. Repeat the bleeding process if required and drive down the road several times to burn off any new residue on your brakes and get your shoes to grip properly.
Caliper, Rear Passenger Side
5191268AA
Q: How to Remove and Replace a Brake Caliper on Chrysler Sebring?
A:
In order to take off and assemble the brake caliper, under the safety precaution, the brake pedal holding tool should depress the brake pedal more than one inch (25 mm) of the travel isolated the master cylinder of the brake hydraulic system, and block the brake fluid leakage. Then lift and prop the car, after that take the three wheel mounting nuts and dismount the tire and wheel assembly. Unscrew the banjo bolt which holds the brake flex hose to the brake caliper throwing away the two washers, which drop off with bolt. In taking out the two brake caliper guide pin bolts, one of them (upper) has a special sleeve that the end of the bolt, and this should be fitted in upper mounting hole when replacing the bolts. The last step is laying off the disc brake caliper that goes through the disc brake adapter bracket and Brake Pads.