How to Install an Exhaust Manifold on Both Sides on Dodge Challenger?

Before mounting the exhaust manifold on the left side, set the gasket and the manifold into place. Then, put the exhaust manifold bolts in the correct sequence and tighten each bolt to a value of 31 Nm (23 ft. lbs.). Once you're done with the coolant bottle, put in the air cleaner housing and, finally, attach the knock sensor. Then, connect the exhaust pipe to the manifold bolts and link the negative battery wire again. To start the job on the right side, put in the exhaust manifold gasket and the exhaust manifold, then install and tighten all the exhaust manifold bolts to 31 Nm (23 ft. lbs.) in the correct pattern. Join the right-hand inner fender wire harness, then install the bracket for the power distribution box and then attach the power distribution box. Then, set up the starter and heat shield and install the knock sensor with its bolts, plus the ends of the exhaust pipe to the manifold. Now, join the negative battery cable back to the battery.

How to Remove and Replace an Exhaust Manifold for Right on Dodge Challenger?

You should first clean the gasket areas when replacing the right exhaust manifold. After replacing the exhaust manifold, tighten the studs at the exhaust outlet to 39 Nm (29 ft. lbs.). Slide the exhaust manifold into position against the gasket, bolt it down with the retaining bolts, tighten them starting from the center and progressing outward to 23 Nm (17 ft. lbs.). Fit the catalytic converter into the exhaust manifold and make sure the ball flange nuts are tightened to 34 Nm (25 ft. lbs.). Place both upper and lower shields in place with two bolts, tightening them to 12 Nm (105 in.lbs.). Mount the engine mount with three bolts and secure them by turning the bolts to 70 Nm (52 ft. lbs.). Attach the engine mount to the car. Fit the upstream oxygen sensor after using the appropriate tool. Attach the upper two exhaust manifold heat shield nuts and tighten them to 8 Nm or 73 in.lbs. Now, make sure to connect the negative battery cable.

OEM Dodge Challenger Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Exhaust Manifolds found

View related parts
Dodge Challenger Exhaust Manifold, Passenger Side Part Number: 53013848AG
$227.73 MSRP: $339.00
You Save: $111.27 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold Exhaust
- Position: Passenger Side
- Replaces: 53013848AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2023 Dodge Challenger | R/T, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Shaker, T/A | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 53013849AE
$217.54 MSRP: $324.00
You Save: $106.46 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Challenger | R/T, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Shaker, T/A | 8 Cyl 5.7 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 4792779AA
$191.98 MSRP: $355.00
You Save: $163.02 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Challenger | SE | 6 Cyl 3.5 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Passenger Side Part Number: 4792778AA
$284.38 MSRP: $423.00
You Save: $138.62 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Challenger | SE | 6 Cyl 3.5 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Passenger Side Part Number: 5038756AC
$801.13 MSRP: $1225.00
You Save: $423.87 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Challenger | R/T Scat Pack, R/T Scat Pack Widebody, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock | 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 5038757AC
$819.91 MSRP: $1250.00
You Save: $430.09 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Challenger | R/T Scat Pack, R/T Scat Pack Widebody, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock | 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 53013849AF
$202.81 MSRP: $301.00
You Save: $98.19 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | R/T | 8 Cyl 5.7 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Passenger Side Part Number: 5038756AB
$830.13 MSRP: $1225.00
You Save: $394.87 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right
- Position: Passenger Side
- Replaces: 5038756AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2021 Dodge Challenger | 392 Hemi Scat Pack Shaker, R/T 392, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, Scat Pack, T/A 392, T/A 392 Widebody | 6.2L V8, 6.4L V8, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 5038757AB
$849.59 MSRP: $1250.00
You Save: $400.41 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left
- Position: Driver Side
- Replaces: 5038757AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2021 Dodge Challenger | 392 Hemi Scat Pack Shaker, R/T 392, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, Scat Pack, T/A 392, T/A 392 Widebody | 6.2L V8, 6.4L V8, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Driver Side Part Number: 5037633AF
$929.05 MSRP: $1310.00
You Save: $380.95 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold Exhaust
- Position: Driver Side
- Replaces: 5037633AD, 5037633AB, 5037633AC, 5037633AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2016 Dodge Challenger | 392 Hemi Scat Pack Shaker, R/T Scat Pack, SRT 392, SRT8, Scat Pack | 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Exhaust Manifold, Passenger Side Part Number: 5037632AF
$957.45 MSRP: $1360.00
You Save: $402.55 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold Exhaust
- Position: Passenger Side
- Replaces: 5037632AE, 5037632AC, 5037632AB, 5037632AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2016 Dodge Challenger | 392 Hemi Scat Pack Shaker, R/T Scat Pack, SRT 392, SRT8, Scat Pack | 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS

Dodge Challenger Exhaust Manifold

Choose OEM Exhaust Manifold that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Exhaust Manifold follows strict manufacturing steps to lock in quality and fit. If your Dodge Challenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Challenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Exhaust Manifold of Dodge Challenger vehicles involves the process of channeling hot exhaust gases from the engine to the exhaust system for an enhanced engine performance. Situated at the top of the exhaust system, the manifold gathers exhaust coming from several cylinder and sends it through the catalytic converter and muffler. This design prevents intake reversion that can cause the loud banging heard in large engines that allows bad gases to flow back into the intake. There has been the use of different types of exhaust manifolds in different models of Dodge Challenger over the years with uses of both cast iron and stainless steel kinds. Performance oriented units referred to as headers are manufactured to decrease the flow restriction and increase the velocity of exhaust gases. Also, in today's models like Yamaha's EXUP, back pressure is varied in relation to the speed of the engine in order to harness the necessary power. Some of the variations in design and materials in these exhaust manifolds are a cause of performance and efficiency of the Dodge Challenger.

Dodge Challenger Exhaust Manifold Parts and Q&A

Exhaust Manifold, Passenger Side
5037632AF
Q: How to Install an Exhaust Manifold on Both Sides on Dodge Challenger?
A:
Before mounting the exhaust manifold on the left side, set the gasket and the manifold into place. Then, put the exhaust manifold bolts in the correct sequence and tighten each bolt to a value of 31 Nm (23 ft. lbs.). Once you're done with the coolant bottle, put in the air cleaner housing and, finally, attach the Knock Sensor. Then, connect the exhaust pipe to the manifold bolts and link the negative battery wire again. To start the job on the right side, put in the exhaust manifold gasket and the exhaust manifold, then install and tighten all the exhaust manifold bolts to 31 Nm (23 ft. lbs.) in the correct pattern. Join the right-hand inner fender wire harness, then install the bracket for the power distribution box and then attach the power distribution box. Then, set up the starter and heat shield and install the knock sensor with its bolts, plus the ends of the exhaust pipe to the manifold. Now, join the negative Battery Cable back to the battery.
Exhaust Manifold, Passenger Side
53013848AG
Q: How to Remove and Replace an Exhaust Manifold for Right on Dodge Challenger?
A:
You should first clean the gasket areas when replacing the right exhaust manifold. After replacing the exhaust manifold, tighten the studs at the exhaust outlet to 39 Nm (29 ft. lbs.). Slide the exhaust manifold into position against the gasket, bolt it down with the retaining bolts, tighten them starting from the center and progressing outward to 23 Nm (17 ft. lbs.). Fit the Catalytic Converter into the exhaust manifold and make sure the ball flange nuts are tightened to 34 Nm (25 ft. lbs.). Place both upper and lower shields in place with two bolts, tightening them to 12 Nm (105 in.lbs.). Mount the Engine Mount with three bolts and secure them by turning the bolts to 70 Nm (52 ft. lbs.). Attach the engine mount to the car. Fit the upstream Oxygen Sensor after using the appropriate tool. Attach the upper two exhaust manifold heat shield nuts and tighten them to 8 Nm or 73 in.lbs. Now, make sure to connect the negative Battery Cable.