How to Maintain and Repair a Fuel Tank on Dodge Charger?

When working on the tank, first release the fuel pressure and disconnect the negative battery cable. Be sure the fuel is below 5/8 of the length so that it does not cause spills as the module disconnects. Take out partial gas by attaching a hard nylon tube with a 30° cut to the check valve to open it. Pull back and up the lower seat cushion, then lift open the back cover by folding the foam cushion behind it. Remove the electrical connector from the left side module and record its correct installation directions. To drain the fuel on the left, remove ring #9340 from the left side module and raise the module enough to place the tip into the tank. Remove the electrical connectors from the module top and lift away the half of the module including the fuel level sending card, return fuel lines and supply fuel line. Remove the fuel line by pushing the button on the release tab and pull out the fuel return line from the lower module. Rotate the module sideways to discharge any fuel left in the tank and take it out of the vehicle. To install the pump, insert the module into the tank again, set up the return lines from the tank and check that the fuel feed line is properly locked. Plug the electrical wires back into the bottom of the module top and attach the module top to the bottom, ensuring the logo is upward. Use tool #9340 to tighten the module with the lock ring, hook up the left side electrical connector and position the plastic access cover in place. Figure 5: Fold the foam pad back into its place, set up the back lower seat cushion, fill the fuel tank and link the negative battery cable. Afterward, use your scan tool to open the fuel system and look for any leaks.

How is the Fuel Tank Installed on Dodge Charger?

Begin by placing the pump in the tank and joining the fuel return lines to the module, so that they are firmly attached. After that, add the fuel line to the module with a secure connection and then attach the circuit board connectors to the bottom of the module top before putting the module top onto the module base. Put the modules side by side and lined up and then use the special #9340 tool to tighten the left lock ring. Plug the electrical connector into the left side module and push on the plastic access cover until it clicks into place, then fold the foam pad back to fit . Install the lower rear seat cushion and make sure it does not move. After that, add fuel to the tank and join the negative battery cable. Once all checks are done, fill the fuel tank one more time and use the scan tool to pressure the fuel system, while watching for any leaks.

OEM Dodge Charger Fuel Tank

Gas Tank

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Fuel Tanks found

View related parts
Dodge Charger Fuel Tank Part Number: 68258722AD
$819.91 MSRP: $1250.00
You Save: $430.09 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68258722AC, 68258722AA, 68258722AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2018 Dodge Charger | Pursuit, SE, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Charger Fuel Tank Part Number: 68494563AB
$908.31 MSRP: $1395.00
You Save: $486.69 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68494563AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2023 Dodge Charger | GT, Pursuit, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68494592AB
$935.94 MSRP: $1430.00
You Save: $494.06 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68494592AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2023 Dodge Charger | Pursuit, R/T | 3.6L V6, 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68051891AB
$1320.48 MSRP: $2000.00
You Save: $679.52 (34%)
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 5170580AC, 68051891AC, 5135172AB, 68051891AA, 5135172AC, 5170580AA, 5170580AB, 5135172AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68102695AI
$581.23 MSRP: $877.00
You Save: $295.77 (34%)
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Charger | Pursuit, R/T, SE | 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68258723AD
$1221.03 MSRP: $1850.00
You Save: $628.97 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68258723AC, 68258723AB, 68258723AA, 68200537AD, 68200537AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68142803AG
$586.76 MSRP: $885.00
You Save: $298.24 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Charger | Pursuit, SE, SXT, SXT Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68142803AE
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68142803AB, 68142803AA, 68142803AC, 68142803AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Charger | Pursuit, SE, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68142792AF
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
- Replaces: 68142792AE, 68142792AC, 68142792AA, 68142792AD, 68142792AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2013 Dodge Charger | SRT8 | 5.7L V8, 6.4L V8, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68102695AG
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68102695AF, 68102695AE, 68102695AA, 68102695AC, 68102695AB, 68102695AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Charger | Pursuit, R/T, SE, SRT8 | 3.6L V6, 5.7L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68142792AG
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Dodge Charger | Pursuit, R/T, SE, SRT8 | 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Fuel Tank Part Number: 68051910AB
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 5135173AE, 5135173AC, 68051910AA, 5135173AB, 68051910AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS

Dodge Charger Fuel Tank

Choose OEM Fuel Tank that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Fuel Tank follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Fuel Tank is an important part of the Dodge Charger automobiles where even along with the fuel, electric fuel pump and fuel gauge sender is also contained. It performs a very significant part in the Evaporative Emission Control System, or EVAP, check valve is designed to prevent the loss of fuel vapors. Dodge Charger Fuel Tanks are of moderate complexity; metal fuel tanks are usually stamped out of sheet metal and then welded together in some instances while the plastic ones are blow molded from High Density Polyethylene (HDPE). Since December 2007, metal tanks were corroding, while plastic tanks were cracking under the influence of temperature variations and vibrations. Fuel tanks have been developing to fuel cells to avoid puncturing and spilling of fuel when involved in a race. Furthermore, high capacity fuel tanks with military grade polymer for seemingly double the driving range up to 400-500 miles is also provided as a corrosion free replacement for steel tanks.

Dodge Charger Fuel Tank Parts and Q&A

Fuel Tank
68051891AB
Q: How to Maintain and Repair a Fuel Tank on Dodge Charger?
A:
When working on the tank, first release the fuel pressure and disconnect the negative Battery Cable. Be sure the fuel is below 5/8 of the length so that it does not cause spills as the module disconnects. Take out partial gas by attaching a hard nylon tube with a 30° cut to the check valve to open it. Pull back and up the lower Seat Cushion, then lift open the back cover by folding the foam cushion behind it. Remove the electrical connector from the left side module and record its correct installation directions. To drain the fuel on the left, remove ring #9340 from the left side module and raise the module enough to place the tip into the tank. Remove the electrical connectors from the module top and lift away the half of the module including the fuel level sending card, return fuel lines and supply fuel line. Remove the fuel line by pushing the button on the release tab and pull out the fuel return line from the lower module. Rotate the module sideways to discharge any fuel left in the tank and take it out of the vehicle. To install the pump, insert the module into the tank again, set up the return lines from the tank and check that the fuel feed line is properly locked. Plug the electrical wires back into the bottom of the module top and attach the module top to the bottom, ensuring the logo is upward. Use tool #9340 to tighten the module with the lock ring, hook up the left side electrical connector and position the plastic access cover in place. Figure 5: Fold the foam pad back into its place, set up the back lower seat cushion, fill the fuel tank and link the negative battery cable. Afterward, use your scan tool to open the fuel system and look for any leaks.
Fuel Tank
68051910AB
Q: How is the Fuel Tank Installed on Dodge Charger?
A:
Begin by placing the pump in the tank and joining the fuel return lines to the module, so that they are firmly attached. After that, add the fuel line to the module with a secure connection and then attach the circuit board connectors to the bottom of the module top before putting the module top onto the module base. Put the modules side by side and lined up and then use the special #9340 tool to tighten the left lock ring. Plug the electrical connector into the left side module and push on the plastic access cover until it clicks into place, then fold the foam pad back to fit . Install the lower rear Seat Cushion and make sure it does not move. After that, add fuel to the tank and join the negative Battery Cable. Once all checks are done, fill the fuel tank one more time and use the scan tool to pressure the fuel system, while watching for any leaks.