How is a Hood Hinge Installed on Dodge Charger?

Line up the rear-side bracket of the hood hinge to the fender ledge on the vehicle, then fasten the two screws that secure it (using 28 Nm (21 ft. lbs.) torque). Then, put the hood panel (2) onto the upper hinge bracket and attach both of the screws (2), tightening them both to 28 Nm (21 ft. lbs.). If possible, put back the upper end of the gas support cylinder on top of the upper hinge bracket. After you finish, take down the support for the hood, shut the hood and organize the hinge so the hood operates as intended and is properly spaced.

How to maintain and fix a hood hinge on Dodge Charger?

With an effective prop or block positioned beneath the hood, make sure the hood is held up during repair work. If the upper gas support cylinder reaches the upper bracket on the hood hinge, disconnect the cylinder end from it. Make a note of where the hood hinge upper bracket sits on the inner hood panel so you can mark it again when reinstalling the hood. Remove the hinge from the hood with the two screws and in the process, position the mark for the hinge lower bracket on the inside of the fender ledge. Following that, unscrew the two bolts at the hinge and lift the hinge out of the hood. Pull the lower hinge bracket upward and clip the screws into the fender hole, so that it is positioned inside the front fender ledge and mount them with 28 N.m (21 ft.lbs.) of torque. Line up the hood panel with the hinge bracket at the top and put in and tighten the two screws using the torque specification. When possible, secure the upper end of the gas support cylinder to the hinge bracket above the door. Once finished, remove the support fixture from the hood, close it and change the hood hinge placement until the hood moves smoothly and fits properly.

OEM Dodge Charger Hood Hinge

Hood Bracket Hinge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Hood Hinges found

View related parts
Dodge Charger Hinge, Front Driver Side Part Number: 5065265AL
$53.90 MSRP: $110.00
You Save: $56.10 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Left; Hinge Hood
- Position: Front Driver Side
- Replaces: 5065265AJ, 5065265AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Hinge, Front Passenger Side Part Number: 5065264AL
$53.90 MSRP: $110.00
You Save: $56.10 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Right; Hinge Hood
- Position: Front Passenger Side
- Replaces: 5065264AK, 5065264AJ
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Hinge, Front Driver Side Part Number: 5065265AH
$37.12 MSRP: $53.35
You Save: $16.23 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Left; Hinge Hood Contains Propeller Stud
- Position: Front Driver Side
- Replaces: 5065265AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Hinge, Front Passenger Side Part Number: 5065264AH
$37.12 MSRP: $53.35
You Save: $16.23 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Right; Hinge Hood Contains Propeller Stud
- Position: Front Passenger Side
- Replaces: 5065264AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Hinge, Front Driver Side Part Number: 55113551AG
$56.84 MSRP: $115.00
You Save: $58.16 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Left; Hinge Hood
- Position: Front Driver Side
- Replaces: 55113551AF, 55113551AE, 55113551AD, 55113551AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Hinge, Front Passenger Side Part Number: 55113550AG
$56.84 MSRP: $115.00
You Save: $58.16 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Hood; Hood Hinge, Front Right; Hinge Hood
- Position: Front Passenger Side
- Replaces: 55113550AF, 55113550AE, 55113550AD, 55113550AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS

Dodge Charger Hood Hinge

Choose OEM Hood Hinge that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Hood Hinge follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Charger Hood Hinge Parts and Q&A

Hinge, Front Passenger Side
5065264AL
Q: How is a Hood Hinge Installed on Dodge Charger?
A:
Line up the rear-side bracket of the hood hinge to the fender ledge on the vehicle, then fasten the two screws that secure it (using 28 Nm (21 ft. lbs.) torque). Then, put the hood panel (2) onto the upper hinge bracket and attach both of the screws (2), tightening them both to 28 Nm (21 ft. lbs.). If possible, put back the upper end of the gas support cylinder on top of the upper hinge bracket. After you finish, take down the support for the hood, shut the hood and organize the hinge so the hood operates as intended and is properly spaced.
Hinge, Front Passenger Side
5065264AH
Q: How to maintain and fix a hood hinge on Dodge Charger?
A:
With an effective prop or block positioned beneath the hood, make sure the hood is held up during repair work. If the upper gas support cylinder reaches the upper bracket on the hood hinge, disconnect the cylinder end from it. Make a note of where the hood hinge upper bracket sits on the inner hood panel so you can mark it again when reinstalling the hood. Remove the hinge from the hood with the two screws and in the process, position the mark for the hinge lower bracket on the inside of the fender ledge. Following that, unscrew the two bolts at the hinge and lift the hinge out of the hood. Pull the lower hinge bracket upward and clip the screws into the fender hole, so that it is positioned inside the front fender ledge and mount them with 28 N.m (21 ft.lbs.) of torque. Line up the hood panel with the hinge bracket at the top and put in and tighten the two screws using the torque specification. When possible, secure the upper end of the gas support cylinder to the hinge bracket above the door. Once finished, remove the support fixture from the hood, close it and change the hood hinge placement until the hood moves smoothly and fits properly.