How to Install a New CV Boot on an Axle Shaft on Dodge Journey?

Put the first clamp over the interconnecting shaft and then put the new outer boot on the shaft, making sure the raised bead in the boot goes into the groove on the shaft. Make sure to use a fresh circlip on your bicycle. Place the splines on the outer CV joint assembly's cross and on the interconnecting shaft so they line up and then begin putting the outer CV joint onto the shaft. Use a gentle hammer to knock the end of the stub axle a few times while the hub nut is fitted, until both the outer CV joint and its cross are fully onto the interconnecting shaft and are resting on the circlip. Use half of the special grease to fill the outer CV joint area and place the rest into the seal boot. Place the outer CV joint sealing onto the interconnecting shaft, position the Crimping Tool C-4975A over the bridge of the clamp and tighten the nut until the jaws are squeezed together. Reach for the seal only once it is not showing any dents, tears or irregularities; manually even it out and fix its shape if required. Fix the sealing boot made from rubber or plastic into the retaining groove on the outer CV joint housing, then attach it evenly to the CV joint retaining clamp. Crimp Tool C-4975A onto the outer CV joint housing and tighten the nut enough that you see the jaws come completely together. Now, attach the unit you replaced the boot on to the vehicle.

How to Replace the Axle Shaft and CV Boot on Dodge Journey?

First, take off the halfshaft assembly to remove the outer boot from the front half shaft. Pull off the main boot retaining clamp from the CV joint housing and then remove the small boot clamp that holds the CV joint outer boot on the interconnecting shaft. Descend the sliding boot to the bottom of the interconnecting shaft once you've removed it from the upper end. Remove any dirt from around the outer CV joint and surrounding interconnecting shaft. Place the interconnecting shaft into a vise, cover its ends and tap the end of the CV joint housing gently to pop it away from the internal circlip. Slide the end of the outer CV joint off the shaft and use taps if it is too tight. Whenever you reassemble, always fit a brand new circlip. Before sliding off the outer CV joint seal, pull out the large circlip on the center of the interconnecting shaft. Also, it's important to carefully inspect and clean the outer joint assembly, as well as the interconnecting joint for signs of additional wear; if there are any worn areas, the halfshaft assembly should be replaced since its parts cannot be serviced.

OEM Dodge Journey Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Axle Shafts found

View related parts
Dodge Journey Axle Assembly, Front Driver Side Part Number: 68079565AB
$334.24 MSRP: $497.00
You Save: $162.76 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 68079565AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2019 Dodge Journey | Crew, Crossroad, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Front Driver Side Part Number: 68067361AB
$335.29 MSRP: $497.00
You Save: $161.71 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 5273545AB, 5273545AC, 5273545AE, 68067361AA, 5273545AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2019 Dodge Journey | Crew, Crossroad, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.5L V6, 3.6L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Front Passenger Side Part Number: 68079566AB
$380.07 MSRP: $576.00
You Save: $195.93 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Axle Shaft; Shaft Front Drive
- Position: Front Passenger Side
- Replaces: 68079566AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2019 Dodge Journey | Crew, Crossroad, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Front Passenger Side Part Number: 5273558AG
$397.75 MSRP: $599.00
You Save: $201.25 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5273558AB, 5273558AF, 5273558AE, 5273558AD, 5273558AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Journey | AVP, Base, Crew, Crossroad, Express, Lux, Mainstreet, R/T, SE, SE Value, SXT | 2.4L L4, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Rear Driver Side Part Number: 4743819AC
$372.33 MSRP: $564.00
You Save: $191.67 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Axle Half; CV Axle Assembly, Rear Left; Constant Velocity Axle; Axle Shaft; Shaft Axle Half; CV Axle Assembly
- Position: Rear Driver Side
- Replaces: 4743819AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2019 Dodge Journey | AVP, Base, Crew, Crossroad, Express, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.5L V6, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Front Passenger Side Part Number: 5273546AF
$396.08 MSRP: $574.00
You Save: $177.92 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5273546AC, 5273546AB, 5273546AE, 5273546AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2019 Dodge Journey | Crew, Crossroad, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.5L V6, 3.6L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Rear Passenger Side Part Number: 4743818AC
$253.54 MSRP: $568.00
You Save: $314.46 (56%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Axle Half; CV Axle Assembly, Rear Right; Constant Velocity Axle; Axle Shaft; Shaft Axle Half; CV Axle Assembly
- Position: Rear Passenger Side
- Replaces: 4743818AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2019 Dodge Journey | AVP, Base, Crew, Crossroad, Express, GT, Limited, Lux, Mainstreet, R/T, SE, SXT | 3.5L V6, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Journey Axle Assembly, Front Driver Side Part Number: 5085180AG
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 5085180AB, 5085180AE, 5085180AF, 5085180AD, 5085180AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Journey | AVP, Base, Crew, Crossroad, Express, R/T, SE, SE Value, SXT | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS

Dodge Journey Axle Shaft

Choose OEM Axle Shaft that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Axle Shaft follows strict manufacturing steps to lock in quality and fit. If your Dodge Journey matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Journey parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Axle Shaft is one of the critical parts of the Dodge Journey, which ensures mileage's enhancement in the vehicle. As one of the components in the power transmission system derived from the differential, the Axle Shaft provides for free rotation of wheels and thus improved adhesion and stability, all of which make a contribution to the reliability which is a characteristic of the Dodge Journey Crossover. Originally developed as a part for the Journey since its model year 2009, the Axle Shaft is one of the structural components that contributes to the load-bearing of the vehicle's weight, transmitting torque, and assuring the perpendicularly positioned wheels would work more efficiently and safely. Specifically, the Dodge Journey has a large number of admirers due to a large area of the cabin that can comfortably accommodate three rows of seats and enhanced security with effective systems of braking that interact with the Axle Shaft. Remarkably, the Dodge Journey Axle Shaft is made in a way that it cannot be easily worn out by various aspects that lead to noisy or vibrating axles which in turn impact the performance of the vehicle. Specifications of the Axle Shaft including one where it is design to transfer the torque to other parts of the vehicle while enhancing durability distinguish it in the automotive industry. This is why the Dodge Journey stood for comfort and reasonable prices even after it was discontinued in 2020, Axle Shaft is one of the main components that contributed to the car's impact on the crossover market.

Dodge Journey Axle Shaft Parts and Q&A

Axle Assembly, Rear Passenger Side
4743818AC
Q: How to Install a New CV Boot on an Axle Shaft on Dodge Journey?
A:
Put the first clamp over the interconnecting shaft and then put the new outer boot on the shaft, making sure the raised bead in the boot goes into the groove on the shaft. Make sure to use a fresh circlip on your bicycle. Place the splines on the outer CV joint assembly's cross and on the interconnecting shaft so they line up and then begin putting the outer CV joint onto the shaft. Use a gentle hammer to knock the end of the stub axle a few times while the hub nut is fitted, until both the outer CV joint and its cross are fully onto the interconnecting shaft and are resting on the circlip. Use half of the special grease to fill the outer CV joint area and place the rest into the seal boot. Place the outer CV joint sealing onto the interconnecting shaft, position the Crimping Tool C-4975A over the bridge of the clamp and tighten the nut until the jaws are squeezed together. Reach for the seal only once it is not showing any dents, tears or irregularities; manually even it out and fix its shape if required. Fix the sealing boot made from rubber or plastic into the retaining groove on the outer CV joint housing, then attach it evenly to the CV joint retaining clamp. Crimp Tool C-4975A onto the outer CV joint housing and tighten the nut enough that you see the jaws come completely together. Now, attach the unit you replaced the boot on to the vehicle.
Axle Assembly, Front Driver Side
68067361AB
Q: How to Replace the Axle Shaft and CV Boot on Dodge Journey?
A:
First, take off the halfshaft assembly to remove the outer boot from the front half shaft. Pull off the main boot retaining clamp from the CV joint housing and then remove the small boot clamp that holds the CV joint outer boot on the interconnecting shaft. Descend the sliding boot to the bottom of the interconnecting shaft once you've removed it from the upper end. Remove any dirt from around the outer CV joint and surrounding interconnecting shaft. Place the interconnecting shaft into a vise, cover its ends and tap the end of the CV joint housing gently to pop it away from the internal circlip. Slide the end of the outer CV joint off the shaft and use taps if it is too tight. Whenever you reassemble, always fit a brand new circlip. Before sliding off the outer CV joint seal, pull out the large circlip on the center of the interconnecting shaft. Also, it's important to carefully inspect and clean the outer joint assembly, as well as the interconnecting joint for signs of additional wear; if there are any worn areas, the halfshaft assembly should be replaced since its parts cannot be serviced.