How to install a rear Bumper Cover on Dodge Magnum?

To install the rear bumper cover, begin by installing the two push-pin retainers and a new nut insert into each quarter panel if they were removed. For SRT8 models, attach the lower fascia to the rear fascia assembly using new metal retaining clips if it was removed. If equipped, install the park assist sensors into the rear fascia assembly. Position the rear fascia assembly onto the vehicle and connect the license plate lamp and park assist wire harness connector if equipped. Engage the two push-pin retainers into the slots on each side of the rear fascia assembly by pushing the fascia forward. Install the push-pin retainers that secure the rear fascia assembly to the decklid sill, using three for sedan and wagon models and one for the charger. On sedan models, install the two bumper stops. Raise and support the vehicle, then install the screws that secure the rear fascia assembly to the nut insert in each quarter panel, tightening them securely. Position each rear wheel house splash shield to the rear fascia assembly and install the push-pin retainers. Finally, lower the vehicle.

How to remove the rear Bumper Cover (fascia) on Dodge Magnum?

To remove the rear bumper cover or fascia, first raise and support the vehicle. Next, take out the three push-pin retainers that secure each rear wheel house splash shield to the rear fascia assembly. Then, remove the screw that secures the rear fascia assembly to the nut insert in each quarter panel. Partially lower the vehicle and remove the push-pin retainers (three for sedan, three for wagon, one for Charger) that secure the rear fascia assembly to the decklid sill. On all models, take out the two deck lid bumper stops. Carefully pull the rear fascia assembly rearward to disengage the two push-pin retainers from the slots on each side of the fascia, allowing access to the license lamp and park assist. If equipped, disconnect the park assist sensor wire harness connector from the tail lamp wire harness connector and remove the rear fascia assembly from the vehicle. If necessary, remove the park assist sensors from the rear fascia assembly. For SRT8 models, if required, remove the lower fascia from the rear fascia assembly and discard the metal retaining clips. Additionally, if needed, remove and discard the nut insert from each quarter panel and take out the two push-pin retainers.

OEM Dodge Magnum Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Bumper Covers found

View related parts
Dodge Magnum Bumper Cover, Black, Front Part Number: 4806179AE
$644.64 MSRP: $939.00
You Save: $294.36 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front
- Position: Front
- Replaces: 4806179AB, 4806179AD, 4806179AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T, SE, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Bumper Cover, Rear Part Number: 4805776AC
$413.35 MSRP: $602.00
You Save: $188.65 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear
- Position: Rear
- Replaces: 4805776AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2008 Dodge Magnum | SE, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Magnum Bumper Cover, Front Part Number: 4805768AB
$333.10 MSRP: $490.00
You Save: $156.90 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Bumper Cover, Dark Silver, Front Part Number: 4806353AA
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | SE, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Magnum Bumper Cover, Rear Part Number: 5030050AB
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear
- Position: Rear
- Replaces: 5030050AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Dodge Magnum | SRT8 | 6.1L V8, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Bumper Cover, Front Part Number: 4854675AA
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Replaces: 5030046AB, 5030046AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Magnum | SRT8 | 6.1L V8, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Bumper Cover, Dark Silver, Front Part Number: 4806458AA
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T | 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Bumper Cover, Rear Part Number: 4806439AA
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T | 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Bumper Cover, Rear Part Number: 4806143AC
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear
- Position: Rear
- Replaces: 4806143AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T | 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Bumper Cover, Front Part Number: 68033608AC
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front
- Position: Front
- Replaces: 68033608AB, 68033608AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | SRT8 | 2.7L V6, 3.5L V6, 5.7L V8, 6.1L V8, 8 Cyl 6.1 L GAS

Dodge Magnum Bumper Cover

Choose OEM Bumper Cover that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Bumper Cover follows strict manufacturing steps to lock in quality and fit. If your Dodge Magnum matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Magnum parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Magnum Bumper Cover is the soft outer panel that conceals the rigid bumper. This gives your Dodge Magnum a smooth curve and enables airflow. This cover helps shield components underneath from minor impacts and road debris while its styled surface helps support the look of the Dodge. The air openings in the Bumper Cover direct air to the radiator, oil cooler, power steering cooler, brake opening, and they may also contain fog lights, parking lights, turn signals, and cornering lights, which are usually outlined by bezels or trim. If your Dodge is in a collision, the Bumper Cover itself and the separate bumper grille or insert piece can break or crack, so these components must be checked and replaced to ensure the bumper protection works correctly. The plastic surface of a Magnum can also fade or deteriorate due to weather. Certain Magnum vehicles are equipped with covert anchor points for a tow eye concealed behind the Bumper Cover, blanked off with a small cover until needed. In order to keep the Dodge Magnum exterior intact, the Bumper Cover must be in good condition.

Dodge Magnum Bumper Cover Parts and Q&A

Bumper Cover, Rear
4805776AC
Q:
How to install a rear Bumper Cover on Dodge Magnum?
A:
To install the rear bumper cover, begin by installing the two push-pin retainers and a new nut insert into each quarter panel if they were removed. For SRT8 models, attach the lower fascia to the rear fascia assembly using new metal retaining clips if it was removed. If equipped, install the park assist sensors into the rear fascia assembly. Position the rear fascia assembly onto the vehicle and connect the license plate lamp and park assist wire harness connector if equipped. Engage the two push-pin retainers into the slots on each side of the rear fascia assembly by pushing the fascia forward. Install the push-pin retainers that secure the rear fascia assembly to the decklid sill, using three for sedan and wagon models and one for the charger. On sedan models, install the two bumper stops. Raise and support the vehicle, then install the screws that secure the rear fascia assembly to the nut insert in each quarter panel, tightening them securely. Position each rear wheel house splash shield to the rear fascia assembly and install the push-pin retainers. Finally, lower the vehicle.
Bumper Cover, Rear
5030050AB
Q:
How to remove the rear Bumper Cover (fascia) on Dodge Magnum?
A:
To remove the rear bumper cover or fascia, first raise and support the vehicle. Next, take out the three push-pin retainers that secure each rear wheel house splash shield to the rear fascia assembly. Then, remove the screw that secures the rear fascia assembly to the nut insert in each quarter panel. Partially lower the vehicle and remove the push-pin retainers (three for sedan, three for wagon, one for Charger) that secure the rear fascia assembly to the decklid sill. On all models, take out the two deck lid bumper stops. Carefully pull the rear fascia assembly rearward to disengage the two push-pin retainers from the slots on each side of the fascia, allowing access to the license lamp and park assist. If equipped, disconnect the park assist sensor wire harness connector from the tail lamp wire harness connector and remove the rear fascia assembly from the vehicle. If necessary, remove the park assist sensors from the rear fascia assembly. For SRT8 models, if required, remove the lower fascia from the rear fascia assembly and discard the metal retaining clips. Additionally, if needed, remove and discard the nut insert from each quarter panel and take out the two push-pin retainers.