How to Service and Repair a Control Arm Bushing for the Lower Control Arm Rear Isolator on Dodge Stratus?

Start with disassembling the lower control arm from the car so you can remove the bushings. Position the Bushing Remover and the Bushing Receiver correctly on Special Tool C-4212-F, taking care that 6756 is set square on the lower control arm. Use the Remover/Installer Special Tool C-4212-F to put pressure on the rear bushing inside the lower control arm. When assembling, hand insert the bushing into the lower control arm until its mounting hole is square then put it in from the machined surface side, with the empty side in the bushing facing away from the ball joint end. Secure Special Tool 6760 onto the screw area of Remover/Installer Special Tool C-4212-F by Attach Bushing Installer, attach Special Tool 6756 to the lower front control arm and make certain Special Tool 6760 is in position over the isolator bushing. Put pressure on the rear bushing with Remover/Installer Special Tool C-4212-F, until it is directly facing the machined surface on the lower control arm. Once you are done, secure the lower control arm assembly to the car until it is complete.

How to Remove and Replace a Control Arm Bushing in the Front Suspension on Dodge Stratus?

Before you can remove and replace the lower control arm isolator bushings, disconnect the lower control arm from the car. Slide the Bushing Installer, Special Tool 6876, onto the screw part of Remover/Installer Special Tool C-4212-F. With your hand, insert the bushing into the front of the lower control arm and check that it is square with its mounting hole. Attach the bushing to the machined part inside the lower control arm bushing hole. Afterward, put the lower control arm on the assembled Special Tools and make sure they are lined up with Special Tool 6758 on the lower control arm and Special Tool 6876 on the isolator bushing. Screw C-4212-F all the way so that the front bushing sits flush with the machined surface of the lower control arm which will give the bushing the correct position. In the end, reattach the lower control arm assembly to the vehicle.

OEM Dodge Stratus Control Arm Bushing

Suspension Arm Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Control Arm Bushings found

View related parts
Dodge Stratus Lower Control Arm Bushing, Front Outer Part Number: 4695116
$15.67 MSRP: $19.87
You Save: $4.20 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Lower Control Arm; Front Lower Outer, Strut Fork, Axle Pivot Bushing.; Lower Control Arm Front Bushing; Right Shock Absorber to LCA Bushing; Control Arm Bushing.
- Position: Front Lower Outer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Lower Control Arm Bushing, Front Inner Part Number: 4616736
$18.88 MSRP: $23.94
You Save: $5.06 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Lower Control Arm; Suspension Control Arm Bushing, Front Lower Inner Rearward; Trailing Arm Bushing; Lower Control Arm Bushings; Seal for Front Suspension Control Arm Ball Joint.
- Position: Front Lower Inner
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Lower Control Arm Bushing, Front Inner Part Number: 4764453AA
$23.03 MSRP: $29.19
You Save: $6.16 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Lower Control Arm; Suspension Control Arm Bushing, Front Lower Inner Forward; Axle Pivot Bushing; Lower Control Arm Front Bushing; Bushing Lower Control Arm; Suspension Control Arm Bushing; Control Arm Bushing
- Position: Front Lower Inner
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bushing, Front Passenger Side Part Number: MR554382
Product Specifications
- Other Name: Bushing - Control Arm; Suspension Control Arm Bushing, Front Right, Front Right Lower; Axle Pivot Bushing; Bushing Control Arm
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bushing, Front Lower Driver Side Part Number: MR554381
Product Specifications
- Other Name: Bushing - Control Arm; Suspension Control Arm Bushing, Front Left, Front Left Lower; Axle Pivot Bushing; Bushing Control Arm
- Position: Front Lower Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bushing, Front Part Number: MR455736
Product Specifications
- Other Name: Bushing Control Arm; Suspension Control Arm Bushing, Front, Front Rearward
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001 Dodge Stratus | SE | 4 Cyl 2.4 L GAS
View related parts
Dodge Stratus Upper Control Arm Bushing, Front Part Number: 4879189AA
Product Specifications
- Other Name: Bushing; Suspension Control Arm Bushing, Front Upper Forward; Axle Pivot Bushing; Axle Beam Mount; Control Arm Bushing
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Lower Control Arm Bushing, Rear Upper Part Number: 4764961AA
Product Specifications
- Other Name: Bushing - Control Arm; Suspension Control Arm Bushing, Rear Upper; Axle Pivot Bushing; Axle Beam Mount; Upper Control Arm Bushing; Bushing; Bushing Control Arm; Control Arm Bushing
- Position: Rear Upper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Lower Control Arm Bushing Part Number: 4695631
Product Specifications
- Other Name: Bushing; Control Arm Bushing; Axle Pivot Bushing; Window Motor; Lower Control Arm Front Bushing; Seal, Front Suspension Control Arm Ball Joint.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Upper Control Arm Bushing, Front Part Number: 4695096
Product Specifications
- Other Name: Bushing; Suspension Control Arm Bushing, Front Upper Rearward; Control Arm Bush Kit; Axle Pivot Bushing.; Lower Control Arm Lower Bushing; Front Suspension Control Arm Ball Joint Seal; Control Arm Bushing
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2005 Dodge Stratus | Base, ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Upper Control Arm Bushing Part Number: 4616430
Product Specifications
- Other Name: Bushing; Suspension Control Arm Bushing; Control Arm Bushing; Axle Beam Mount; Arm Assembly, Upper Control, Right; Bushing Control Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

Dodge Stratus Control Arm Bushing

Choose OEM Control Arm Bushing that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Control Arm Bushing follows strict manufacturing steps to lock in quality and fit. If your Dodge Stratus matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Stratus parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Stratus Control Arm Bushing is one of the Dodge Stratus suspension parts which is highly valued for its quality and durability, fitting the models of Dodge Stratus automobiles from 1995 to 2005. As a component linking the control arm to the car's frame, the Control Arm Bushing exhibits flexibility to provide a pivot support with limited friction as it moves according to road feedbacks and the driver's steering habits. This functionality is very important in the maintenance of the performance and safety of the Dodge Stratus because; if the bushings are worn out or damaged the performance of the vehicle suspension is affected as well as the wheel alignment. The Dodge Stratus Control Arm Bushing is provided in a rubber, steel, aluminium, polyurethane as well as synthetic elastomer that make it possible for the driver to apply depending on each driver's driving climates as well as the performance they expect. Namely, the Control Arm Bushing is designed to optimize the general handling by limiting the lateral motions of the wheels. However, the Dodge Stratus is famous for its performance parameters, such as reaching the speed of 60 mph in 7.6 seconds; it should also be noted that the Control Arm Bushing is one of the critical components that contribute to this result. This Dodge Stratus Control Arm Bushing is well-made and very effective for ensuring a safe and responsive performance of the Dodge Stratus car models in the car market.

Dodge Stratus Control Arm Bushing Parts and Q&A

Upper Control Arm Bushing
4616430
Q: How to Service and Repair a Control Arm Bushing for the Lower Control Arm Rear Isolator on Dodge Stratus?
A:
Start with disassembling the lower Control Arm from the car so you can remove the bushings. Position the Bushing Remover and the Bushing Receiver correctly on Special Tool C-4212-F, taking care that 6756 is set square on the lower control arm. Use the Remover/Installer Special Tool C-4212-F to put pressure on the rear bushing inside the lower control arm. When assembling, hand insert the bushing into the lower control arm until its mounting hole is square then put it in from the machined surface side, with the empty side in the bushing facing away from the Ball Joint end. Secure Special Tool 6760 onto the screw area of Remover/Installer Special Tool C-4212-F by Attach Bushing Installer, attach Special Tool 6756 to the lower front control arm and make certain Special Tool 6760 is in position over the isolator bushing. Put pressure on the rear bushing with Remover/Installer Special Tool C-4212-F, until it is directly facing the machined surface on the lower control arm. Once you are done, secure the lower control arm assembly to the car until it is complete.
Lower Control Arm Bushing, Front Inner
4616736
Q: How to Remove and Replace a Control Arm Bushing in the Front Suspension on Dodge Stratus?
A:
Before you can remove and replace the lower Control Arm isolator bushings, disconnect the lower control arm from the car. Slide the Bushing Installer, Special Tool 6876, onto the screw part of Remover/Installer Special Tool C-4212-F. With your hand, insert the bushing into the front of the lower control arm and check that it is square with its mounting hole. Attach the bushing to the machined part inside the lower control arm bushing hole. Afterward, put the lower control arm on the assembled Special Tools and make sure they are lined up with Special Tool 6758 on the lower control arm and Special Tool 6876 on the isolator bushing. Screw C-4212-F all the way so that the front bushing sits flush with the machined surface of the lower control arm which will give the bushing the correct position. In the end, reattach the lower control arm assembly to the vehicle.