How to Install Sway Bar Bushings on the Rear Stabilizer on Dodge Viper?

The first step is to completely clean all the dirt from the sway bar where the bushings will go. To install a bushing on the sway bar, make an opening in the bushing, slip it around the bar and place it against the retainer ring. After that, fit the retainers over the bushings and slide them onto the frame rails. Put the four retainer bolts in place and tighten them to 91 Nm (67 ft. lbs.). Following this, attach the wheel and tire assembly, tightening the nuts one at a time along the suggested sequence to 135 Nm (100 ft. lbs.). Lastly, set the vehicle to go low.

How to Service and Repair a Sway Bar Bushing on Dodge Viper?

Before you start any repair or servicing of the sway bar bushing, it is necessary to lift the vehicle. Take out the bolts holding the sway bar bushing retainers to the upper frame rail, after which remove the retainers from the bushings on the sway bar. The old bushings can be taken out by widening the slit and peeling them off the bar. After that, make sure to thoroughly wash the portion of the sway bar that meets the bushing. Open up the slit and then wrap the new bushings loosely around the sway bar, with the clips touching the retainer. Gently fit the bushing retainers onto the bushings and secure the sway bar retainer bolts with an even pressure and tighten each bolt to 68 Nm (50 ft. lbs.) Last, bring the vehicle down to the floor.

OEM Dodge Viper Sway Bar Bushing

Stabilizer Sway Bar Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Sway Bar Bushings found

View related parts
Dodge Viper Stabilizer Bar Bushing, Rear Part Number: 4643004
Product Specifications
- Other Name: Bushing - Stabilizer Bar; Suspension Stabilizer Bar Bushing, Front, Rear; Sway Bar Bushing; Bushings; Bushing Stabilizer Bar; Bushing
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017, 2008-2010, 1992-2006 Dodge Viper | ACR, Base, GT, GT2, GTC, GTS, R/T-10, SRT, SRT-10, SRT-10 ACR | 10 Cyl 8.0 L GAS, 10 Cyl 8.3 L GAS, 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Stabilizer Bar Bushing Part Number: 4643031
Product Specifications
- Other Name: Bushing - Sway Bar; Sway Bar Bushing; Bushings; Bushing Stabilizer Bar; Bushing, Rear Sway Bar; Bushing, Sway Bar
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2002 Dodge Viper | ACR, Base, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS

Dodge Viper Sway Bar Bushing

Choose OEM Sway Bar Bushing that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Sway Bar Bushing follows strict manufacturing steps to lock in quality and fit. If your Dodge Viper matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Viper parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Viper Sway Bar Bushing is a very useful component that plays an important role of boosting the performance and durability of Dodge Viper cars. Mounted to reduce shocks resulting from hitches on the road and alike, materializes the Sway Bar Bushing which holds the sway bar commonly known as stabilizer bar whose duty is to control body sway during cornering. This is especially true for the Dodge Viper which is well endowed with a V10 engine power and remarkable sports like handling. Designed to fit into the vehicle models of Viper like RT/10, GTS, Sway Bar Bushing enables drivers to achieve a right and stable ride thus improving on the efficiency and safety to be achieved on the road. Sway Bar Bushings should be properly maintained as corroded ones may make the vehicle respond slowly to commands and create disturbing noises. Thus, Dodge Viper Sway Bar Bushing offers more than adequate performance and durability for cars undergoing hard usage in the automotive market. Thus, technical strangs, which can appear during the car's operation, can be addressed instantly, and this will allow driving the Dodge Viper with the maximum level of comfort and performance. To sum it up, the Dodge Viper Sway Bar Bushing can be considered as the vital element of the Viper's construction which in its turn plays significant role among the legends of sports cars.

Dodge Viper Sway Bar Bushing Parts and Q&A

Stabilizer Bar Bushing, Rear
4643004
Q: How to Install Sway Bar Bushings on the Rear Stabilizer on Dodge Viper?
A:
The first step is to completely clean all the dirt from the sway bar where the bushings will go. To install a bushing on the sway bar, make an opening in the bushing, slip it around the bar and place it against the retainer ring. After that, fit the retainers over the bushings and slide them onto the frame rails. Put the four retainer bolts in place and tighten them to 91 Nm (67 ft. lbs.). Following this, attach the wheel and tire assembly, tightening the nuts one at a time along the suggested sequence to 135 Nm (100 ft. lbs.). Lastly, set the vehicle to go low.
Stabilizer Bar Bushing
4643031
Q: How to Service and Repair a Sway Bar Bushing on Dodge Viper?
A:
Before you start any repair or servicing of the sway bar bushing, it is necessary to lift the vehicle. Take out the bolts holding the sway bar bushing retainers to the upper frame rail, after which remove the retainers from the bushings on the sway bar. The old bushings can be taken out by widening the slit and peeling them off the bar. After that, make sure to thoroughly wash the portion of the sway bar that meets the bushing. Open up the slit and then wrap the new bushings loosely around the sway bar, with the clips touching the retainer. Gently fit the bushing retainers onto the bushings and secure the sway bar retainer bolts with an even pressure and tighten each bolt to 68 Nm (50 ft. lbs.) Last, bring the vehicle down to the floor.