What are the steps involved in replacing the Axle Shaft, Wheel Bearing, and Wheel Seal on the Dodge Ramcharger?

Two axleshaft oil seals are utilized on this type of axle, consisting of an inner and an outer seal, with oil seepage at the outer seal typically indicating inner seal failure. Begin by raising the rear of the vehicle and supporting it on jackstands, then remove the wheel and brake drum. Access the axleshaft end flange to unscrew the retainer nuts, and use a slide hammer to withdraw the axleshaft while removing the brake assembly and gaskets. A special tool is required to extract the inner oil seal from the axle housing. Clean the axle housing seal bore and drive in a new seal using a piece of pipe or a large socket and a hammer. If dismantling the axleshaft, cut grooves across the bearing collar with a sharp chisel for removal, avoiding heat to prevent damaging the axleshaft temper. Remove the bearing collar retainer by cutting off the lower edge with a chisel, grind off a section of the bearing inner track flange, and use pliers to remove the bearing rollers. Pull down the roller cage and cut it out, then remove the roller bearing outer track. Protect the seal surface with tape before withdrawing the bearing inner track with a puller, and take out the axleshaft outer seal from the retainer plate. Begin reassembly by installing the retainer plate with a new seal on the axleshaft, press wheel bearing grease into the bearing roller, and install the new bearing outer track, bearing, and collar using a puller. Place a new rubber-coated steel gasket over the axle housing flange studs, followed by the brake assembly, and apply grease to the outer diameter of the bearing outer track to prevent corrosion. Install a foam gasket over the axle housing flange studs, then carefully slide the axleshaft assembly into the housing until the splines engage in the differential side gears, tapping it with a soft-faced hammer until fully seated. Install the retainer nuts, tightening the lower one first, and back off the threaded adjuster before installing the right-hand axleshaft. If any axleshafts have been removed or new components installed, adjust the axleshaft end play with both rear wheels off the ground by turning the axleshaft adjuster ring on the right-hand axleshaft until all end play disappears, then turn the adjuster four notches counterclockwise for the correct end play, ideally between 0.008 and 0.018 inches, using a dial gauge for accuracy. Once the end play is correct, remove one support plate retainer nut and install the adjuster lock, ensuring the tab engages with the notch in the adjuster. Finally, install the brake drums and wheels, and lower the vehicle to the ground.

OEM Dodge Wheel Seal

Wheel Axle Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Wheel Seals found

View related parts
Dodge Bearing Seal, Rear Part Number: 5086773AC
$62.82 MSRP: $89.95
You Save: $27.13 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Rear; Axle Seal; Seal Wheel Bearing; Wheel Seal
- Position: Rear
- Replaces: 5086773AB
Fits the following Dodge Models:
- Ram 1500 | 2006-2008 | Laramie, SLT, SXT | 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
- Ram 2500 | 2003-2010 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
- Ram 3500 | 2003-2010 | Laramie, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View More
View related parts
Dodge Bearing Seal, Rear Part Number: 5086983AA
$55.18 MSRP: $81.75
You Save: $26.57 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Rear; Axle Seal; Inner Seal; Seal Wheel Bearing; Wheel Seal
- Position: Rear
Fits the following Dodge Models:
- Ram 2500 | 2003-2009 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
- Ram 3500 | 2003-2009 | Laramie, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Dodge Bearing Seal Part Number: 4238789
$5.44 MSRP: $6.90
You Save: $1.46 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Rear Wheel Brake Hub Ducellier; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Rear Seal; Hub Seals; Seal, Dust
Fits the following Dodge Models:
- Caravan | 1989-1995 | Base, C/V, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L CNG, 6 Cyl 3.3 L GAS
- Grand Caravan | 1989-1995 | Base, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Dodge Oil Seal Part Number: 4238570
$8.22 MSRP: $10.42
You Save: $2.20 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Hub; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Bearing Seal; Wheel Bearing Dust Shield; Grease Seal; Rear Seal; Hub Seals; Inner Bearing Seal.
Fits the following Dodge Models:
- 600 | 1984-1988 | Base, ES, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS
- Aries | 1984-1989 | America, Base, Custom, LE, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS
- Charger | 1984-1987 | 2.2, Base, Shelby | 4 Cyl 1.6 L GAS, 4 Cyl 2.2 L GAS
- Daytona | 1984-1993 | Base, ES, ES Turbo, Iroc, Iroc R/T, Pacifica, Shelby, Shelby Z, Turbo, Turbo Z | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Dynasty | 1988-1993 | Base, LE, LS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Lancer | 1985-1989 | Base, ES, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
- Omni | 1984-1990 | America, Base, GLH, SE | 4 Cyl 1.6 L GAS, 4 Cyl 2.2 L GAS
- Rampage | 1984 | Base | 4 Cyl 2.2 L GAS
- Shadow | 1987-1994 | America, Base, ES, High Line, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Spirit | 1989-1995 | Base, ES, High Line, LE, R/T | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Dodge Bearing Seal Part Number: 2954738
$42.51 MSRP: $61.35
You Save: $18.84 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal; Axle Seal; Axle Seals; Wheel Bearing Seal; Rear Hub Seal; Seal, Rear Wheel Bearing Oil
Fits the following Dodge Models:
- B150 | 1984-1990 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B250 | 1984-1990 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1984-1990 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1990-1993 | Base, S | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1990-1993 | Base | 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1990-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ram 3500 | 1994-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ramcharger | 1990-1993 | Base, Canyon Sport, Royal SE | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W150 | 1990-1993 | Base, S | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W250 | 1990-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Bearing Seal, Rear Part Number: 5003464AA
$27.07 MSRP: $39.95
You Save: $12.88 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Rear; Axle Seal; Hub Seals; Rear Hub Seal; Seal Wheel Bearing; Seal, Wheel Oil; Wheel Seal
- Position: Rear
Fits the following Dodge Models:
- Ram 2500 | 1998-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ram 3500 Van | 2000-2003 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.2 L LPG, 8 Cyl 5.9 L GAS
- Ram Van | 1994-1996 | 3.9L V6, 5.2L V8, 5.9L V8
- Ram Wagon | 1994-1996 | 3.9L V6, 5.2L V8, 5.9L V8
View More
View related parts
Dodge Front Hub Seal, Outer Part Number: 5139359AA
$11.37 MSRP: $14.42
You Save: $3.05 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Front Outer; Axle Seal; Hub Front Seal; Seal Wheel Hub; Wheel Seal
- Position: Front Outer
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Bearing Seal, Rear Part Number: 5103566AA
$48.54 MSRP: $72.25
You Save: $23.71 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Rear; Axle Seal; Axle Seals; Seal Wheel Bearing; Wheel Seal
- Position: Rear
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Bearing Seal Part Number: 52007661
$14.57 MSRP: $18.75
You Save: $4.18 (23%)
ADD TO CART
Product Specifications
- Other Name: Seal - Hub; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Hub Seals; Seal, Front Wheel Bearing Oil; Seal Hub
Fits the following Dodge Models:
- Ram 1500 | 1994-1999 | Base, LT, Laramie, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1994-1999 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 3500 | 1994-1999 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Pinion Seal, Rear Part Number: 4862634AB
$44.21 MSRP: $65.70
You Save: $21.49 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal; Differential Pinion Seal, Rear; Differential Seal; Axle Seal; Bearing Seal; Gasket
- Position: Rear
- Replaces: 4862634AA
Fits the following Dodge Models:
- Charger | 2007-2009 | Pursuit, R/T, SE, SRT8, SXT | 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
- Durango | 2011-2012 | Citadel, Crew, Express, Heat, R/T, SXT, Special Service | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
- Magnum | 2007-2008, 2005 | 3.5L V6, 5.7L V8, 6.1L V8
View More
View related parts
Dodge Bearing Seal Part Number: 3821519AB
$12.98 MSRP: $21.30
You Save: $8.32 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Hub Seals
Fits the following Dodge Models:
- D100 | 1984-1989 | Custom | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1984-1993 | Base, S | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1984-1993 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1984-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ramcharger | 1984-1993 | Base, Canyon Sport, Royal SE | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W100 | 1984-1989 | Custom | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W150 | 1984-1993 | Base, S | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W250 | 1984-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W350 | 1984-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Bearing Seal, Rear Part Number: 3496557
$38.14 MSRP: $56.80
You Save: $18.66 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Rear; Axle Seal; Axle Seals; Wheel Bearing Seal; Hub Seals; Rear Hub Seal; Wheel Seal
- Position: Rear
Fits the following Dodge Models:
- B150 | 1984-1990 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B250 | 1984-1990 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1984-1994 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B3500 | 1995-1998 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1990-1993 | Base, S | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1990-1993 | Base | 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1990-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ram 2500 | 2000-2002, 1994-1998 | Base | 10 Cyl 8.0 L GAS, 5.2L V8, 5.9L L6, 5.9L V8, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS, 8.0L V10
- Ram 3500 | 1994-1996 | 5.9L L6, 5.9L V8, 8.0L V10
- Ram 3500 Van | 2002-2003, 1999 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Bearing Seal Part Number: 52007658
$8.72 MSRP: $11.05
You Save: $2.33 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Hub; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Hub Seals; Seal, Front Wheel Bearing Oil; Seal Hub
Fits the following Dodge Models:
- Ram 1500 | 1994-1999 | Base, LT, Laramie, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1994-1999 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 3500 | 1994-1999 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Front Hub Seal, Inner Part Number: 5103901AB
$16.36 MSRP: $29.85
You Save: $13.49 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Hub; Wheel Seal, Front Inner; Axle Seal; Hub Rear Seal; Seal Hub; Wheel Seal
- Position: Front Inner
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Grease Seal Part Number: MB808444
$2.10 MSRP: $2.67
You Save: $0.57 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal Wheel Hub; Wheel Hub Repair Kit; Wheel Seal; Axle Seal; Hub Seals; Oil Seal, Outer
Fits the following Dodge Models:
- Colt | 1993-1994 | Base, ES, GL | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Dodge Bearing Seal, Front Part Number: 3699678AB
Product Specifications
- Other Name: Seal - Wheel Bearing; Wheel Seal, Front; Wheel Hub Repair Kit; Axle Seal; Wheel Bearing Seal; Hub Seals; Front Hub Seal; Seal; Seal Wheel Bearing; Wheel Seal
- Position: Front
Fits the following Dodge Models:
- B150 | 1984-1994 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B1500 | 1995-1998 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B250 | 1984-1994 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B2500 | 1995-1998 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.2 L LPG, 8 Cyl 5.9 L GAS
- B350 | 1992-1994, 1984-1990 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B3500 | 1995-1998 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.2 L LPG, 8 Cyl 5.9 L GAS
- D100 | 1984-1989 | Custom | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1984-1993 | Base, S | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1984-1993 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1984-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Oil Seal Part Number: MB303875
Product Specifications
- Other Name: Seal - Wheel Hub; Wheel Hub Repair Kit; Multi-Purpose Seal; Wheel Seal; Axle Seal; Bearing Seal; Grease Seal; Hub Seals; Bearing Oil Seal
Fits the following Dodge Models:
- Colt | 1984-1991 | Base, DL, E, GL, GT, Premier, Vista, Vista Custom | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Dodge Grease Seal Part Number: MB808443
Product Specifications
- Other Name: Seal Wheel Hub; Hub Seals; Oil Seal, Inner
Fits the following Dodge Models:
- Colt | 1993-1994 | Base, ES, GL | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Dodge Wheel Bearing Seal Part Number: MT141132
Product Specifications
- Other Name: Seal - Oil Seal, Front Wheel Hub; Wheel Hub Repair Kit; Multi-Purpose Seal; Wheel Seal; Axle Seal; Hub Seals; Seal; Oil Seal, Outer; Oil Seal
Fits the following Dodge Models:
- Ram 50 | 1984-1993 | Base, Custom, LE, Royal, SE, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Seal - Output Part Number: 68530764AB
$27.20 MSRP: $39.20
You Save: $12.00 (31%)
Product Specifications
- Other Name: SEAL-OUTPUT
Fits the following Dodge Models:
- Challenger | 2015-2023 | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Jailbreak, SRT Super Stock, SXT, SXT Plus, Scat Pack 392 Widebody, T/A 392 Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8
- Charger | 2015-2023 | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- Durango | 2011-2025 | Citadel, Crew, Express, GT, GT Plus, GT Premium, Heat, Limited, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Rallye, SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium, SXT, SXT Plus, Special Service | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View More

| Page 1 of 2 |Next >

1-20 of 23 Results

Dodge Wheel Seal

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Wheel Seal for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Wheel Seal keeps the bearings cool and rolling with no drama by blocking out grit and water. Dodge has been in a dirty machine shop since it began, and it never lost that punch, matching the original all-steel body of 1914 with a habit of filling roads with power, then sharpening its attitude with HEMI thunder, Viper audacity, and the 600 watt Fratzonic roar that switches between Drag lunacy and Sport bite, Donut spins, or stealth hush at the flip of a switch. Dodge is crass to touch; the group is low on slick paint, high on straightforward metal, and driver-oriented tech and gives a straightforward shot of confidence since every single system, roaring exhaust channels, adaptive modes, is right there to make the car feel like it is moving through your fingers. Dodge prevents abuse in chewing hubs by forming the Wheel Seal using hard lip edges that hold grease, fit into places with ease, and shake off sand, rocks, rain, and extreme temperatures, therefore making the bearing oily, staying cool and keeping the rolling load to the minimal in thousands of rough miles; the Wheel Seal has a big job in a small package. Dodge supports dozens of Wheel Seal designs front or rear where a customer wants, and they can be matched in a one-piece or an entire set without any hassles and protect each bearing unit against leaks, dirt, and heat whether the customer is commuting to work or faces the back-road haul.

Dodge Wheel Seal Parts and Q&A

Bearing Seal
2954738
Q: What are the steps involved in replacing the Axle Shaft, Wheel Bearing, and Wheel Seal on the Dodge Ramcharger?
A:
Two axleshaft oil seals are utilized on this type of axle, consisting of an inner and an outer seal, with oil seepage at the outer seal typically indicating inner seal failure. Begin by raising the rear of the vehicle and supporting it on jackstands, then remove the wheel and brake drum. Access the axleshaft end flange to unscrew the retainer nuts, and use a slide hammer to withdraw the axleshaft while removing the brake assembly and gaskets. A special tool is required to extract the inner oil seal from the axle housing. Clean the axle housing seal bore and drive in a new seal using a piece of pipe or a large socket and a hammer. If dismantling the axleshaft, cut grooves across the bearing collar with a sharp chisel for removal, avoiding heat to prevent damaging the axleshaft temper. Remove the bearing collar retainer by cutting off the lower edge with a chisel, grind off a section of the bearing inner track flange, and use pliers to remove the bearing rollers. Pull down the roller cage and cut it out, then remove the roller bearing outer track. Protect the seal surface with tape before withdrawing the bearing inner track with a puller, and take out the axleshaft outer seal from the retainer plate. Begin reassembly by installing the retainer plate with a new seal on the axleshaft, press wheel bearing grease into the bearing roller, and install the new bearing outer track, bearing, and collar using a puller. Place a new rubber-coated steel gasket over the axle housing flange studs, followed by the brake assembly, and apply grease to the outer diameter of the bearing outer track to prevent corrosion. Install a foam gasket over the axle housing flange studs, then carefully slide the axleshaft assembly into the housing until the splines engage in the differential side gears, tapping it with a soft-faced hammer until fully seated. Install the retainer nuts, tightening the lower one first, and back off the threaded adjuster before installing the right-hand axleshaft. If any axleshafts have been removed or new components installed, adjust the axleshaft end play with both rear wheels off the ground by turning the axleshaft adjuster ring on the right-hand axleshaft until all end play disappears, then turn the adjuster four notches counterclockwise for the correct end play, ideally between 0.008 and 0.018 inches, using a dial gauge for accuracy. Once the end play is correct, remove one support plate retainer nut and install the adjuster lock, ensuring the tab engages with the notch in the adjuster. Finally, install the brake drums and wheels, and lower the vehicle to the ground.