How to Install a Driveshaft Center Support Bearing on Dodge Charger?

Before installing the driveshaft center support bearing, drop the propeller shaft rear segment into a press so that it rests on the joint yoke. After that, place the bearing assembly over the shaft. C-4735 installer uses: Place the assembled bearings onto the shaft. When the propeller shaft comes out of the press, fasten boot 1 to the section at the rear of the shaft. The propeller shaft spline interface uses a "skip-tooth" shape so that there is only one correct way to assemble it and avoid problems with balance. Line up the blue marks you noticed while taking the frames apart and then match the front section to the rear section. Next, install boot 2 onto the first area, making sure it goes into groove 3. After that, put the propeller shaft back into your vehicle.

How to Service and Repair a Driveshaft Center Support Bearing for HD on Dodge Ram 1500?

To service the driveshaft center support bearing, take out the rear propeller shaft and place marks on the rear and front propeller shafts for future reference. After that, take off the slip joint boot clamp, move the boot down from the boot collar and divide the two shafts. Insert Position Bearing Splitter Tool 1130 in the gap of the propeller shaft and driveshaft center support bearing, then add Bridge 938 to the tool to remove the driveshaft center support bearing. Place the driveshaft center support bearing and boot collar over the shaft, followed by using Installer 1346448A to set the driveshaft center support bearing and boot collar. Grease both the inner and outer splines on the shaft, place the two halves against one another and slide the whole system into place. Next, put the slip yoke boot onto the boot collar and secure it with the boot clamp and lastly install the propeller shaft to the vehicle. Since launch shudder is caused by initial acceleration, decrease the driveshaft center support bearing height by 3.0 mm (0.125 inch) at a time using shim stock or plates and not washers and use bolts with the correct length.

OEM Dodge Driveshaft Center Support Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Driveshaft Center Support Bearings found

View related parts
Dodge Bearing Kit Drive Shaft Part Number: 68065237AA
$166.55 MSRP: $248.00
You Save: $81.45 (33%)
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft
Fits the following Dodge Models:
- Ram 2500 | 2010 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
- Ram 3500 | 2010 | Laramie, SLT, ST | 6 Cyl 6.7 L DIESEL
View related parts
Dodge Center Bearing Part Number: 5183094AC
$171.71 MSRP: $257.00
You Save: $85.29 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Driveshaft Center Support Bearing; Bearing Kit Drive Shaft
- Replaces: 5183094AB, 5183094AA
Fits the following Dodge Models:
- Ram 2500 | 2006-2009 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
- Ram 3500 | 2006-2009 | Laramie, SLT, ST, SXT, Sport | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Center Bearing Part Number: 5183075AC
$164.29 MSRP: $242.00
You Save: $77.71 (33%)
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Driveshaft Center Support Bearing; Bearing Kit Drive Shaft
- Replaces: 5183075AB
Fits the following Dodge Models:
- Ram 2500 | 2006-2009 | Laramie, SLT, ST, SXT | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
- Ram 3500 | 2007-2009 | Laramie, SLT, ST, SXT | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Center Bearing Part Number: 5014097AA
$152.96 MSRP: $225.00
You Save: $72.04 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Center Bearing Drive Shaft; Bearing Kit Drive Shaft
Fits the following Dodge Models:
- D100 | 1984-1989 | Custom | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1984-1993 | Base, S | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1984-1993 | Base | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1984-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Dakota | 2005-2007, 1997-2002 | Base, Laramie, R/T, SLT, ST, SXT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 1500 | 2001-2008, 1994-1999 | Base, LT, Laramie, SLT, SRT-10, SS/T 5.9L, ST, SXT, Sport, TRX4, WS | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 2003-2005, 2001, 1994-1999 | Base, Laramie, SLT, ST | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
- Ram 3500 | 2003-2005, 2001, 1994-1999 | Base, Laramie, SLT, ST | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
- Ramcharger | 1984-1993 | Base, Canyon Sport, Royal SE | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W100 | 1984-1989 | Custom | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Center Bearing Part Number: 4773014
$75.97 MSRP: $115.00
You Save: $39.03 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Bearing Package, Driveshaft Center; Bearing Package, Center; Bearing Drive Shaft
Fits the following Dodge Models:
- Ram 1500 | 1994-2001 | Base, LT, Laramie, SLT, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1994-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 3500 | 1994-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Bearing Kit Drive Shaft Part Number: 68065263AA
$220.94 MSRP: $329.00
You Save: $108.06 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft
Fits the following Dodge Models:
- Ram 2500 | 2010 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
- Ram 3500 | 2010 | Laramie, SLT, ST | 6 Cyl 6.7 L DIESEL
View related parts
Dodge Center Bearing Part Number: 5161435AA
$364.11 MSRP: $534.00
You Save: $169.89 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Bearing Drive Shaft
- Replaces: 5142476AA
Fits the following Dodge Models:
- Challenger | 2010-2014 | R/T, R/T Classic, Rallye Redline, SE, SRT8, SXT, SXT Plus | 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
- Charger | 2006-2014 | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT, SXT Plus | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
- Magnum | 2005-2008 | R/T, SE, SRT8, SXT, SXT Special Edition | 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View More
View related parts
Dodge Center Bearing Part Number: MB505495
Product Specifications
- Other Name: Bearing - Propeller Shaft; Bearing, Center Propeller Shaft; Bearing, Center
Fits the following Dodge Models:
- Stealth | 1991-1996 | Base, ES, R/T, R/T Turbo | 6 Cyl 3.0 L GAS
View related parts
Dodge Center Bearing Part Number: 68043376AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Bearing Drive Shaft
Fits the following Dodge Models:
- Challenger | 2008-2014 | R/T, R/T Classic, Rallye Redline, SE, SRT8, SXT, SXT Plus | 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Center Bearing Part Number: 5080662AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Center Bearing Drive Shaft
Fits the following Dodge Models:
- Dakota | 2003-2004 | Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
- Ram 1500 | 2006 | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Center Bearing Part Number: MB505286
Product Specifications
- Other Name: Center Bearing, Propeller Shaft; Driveshaft Center Support Bearing
- Position: Center
Fits the following Dodge Models:
- Colt | 1989-1990 | Base, DL, E, GL, GT, Vista | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Dodge Center Bearing Part Number: 68031835AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Driveshaft Center Support Bearing
- Replaces: 68006649AA
Fits the following Dodge Models:
- Sprinter 2500 | 2007-2009 | Base | 3.0L V6, 3.5L V6, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
- Sprinter 3500 | 2007-2009 | Base | 3.0L V6, 3.5L V6, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
View related parts
Dodge Center Bearing Part Number: 5135580AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Center Bearing Drive Shaft; Bearing Kit Drive Shaft
Fits the following Dodge Models:
- Dakota | 2005-2007 | Laramie, SLT, ST, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
- Ram 1500 | 2006-2008 | Laramie, SLT, SRT-10, ST, SXT, Sport, TRX4 | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Center Bearing Part Number: 5104574AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Center Bearing Drive Shaft
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Center Bearing Part Number: 5014586AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Bearing Drive Shaft
Fits the following Dodge Models:
- Ram 1500 | 2001 | Laramie, SLT, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 2001-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ram 3500 | 2001-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Center Bearing Part Number: 68031836AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Bearing Drive Shaft
Fits the following Dodge Models:
- Sprinter 2500 | 2007-2009 | Base | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
- Sprinter 3500 | 2007-2009 | Base | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS

Dodge Driveshaft Center Support Bearing

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Driveshaft Center Support Bearing for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Driveshaft Center Support Bearing reduces vibration and maintains a smooth delivery of power under all loads. Dodge had leaped out of a dirty machine shop and had never lost its hammer-on-anvil manner. In 1914, Dodge established its reputation by the first mass-produced all-steel body, emphasizing strength rather than ornament. Dodge is doing the same now with HEMI muscle, Viper DNA, and a Fratzonic exhaust that screams when you step on it. It switches between Drag, Donut, Sport, or whisper-quiet Stealth at the flick of a switch, electric or gasoline. Drivers are not apologized to, but rather empowered by the brand, as they are making machines that are also supposed to push you into the seat. Driveshaft Center Support Bearing is located in the middle of the shaft and it supports a two-piece propeller that remains straight when the torque passes through the propeller. Rubber isolation rings absorb the shake, the forged inner race rotates with the shaft, and the bracket is fixed to the chassis in a manner that road bumps do not translate to steering shudder when it is being run at high speed. Driveshaft Center Support Bearing ensures that U-joints stay aligned and allow arcs of the suspension to flex and not grind metal. Driveshaft Center Support Bearing also reduces the noise of the driveline as it causes the pivot to be locked in full contact with the oil film. The difference is felt by Dodge owners who realize that a new Driveshaft Center Support Bearing kills that howl and returns a silky launch.

Dodge Driveshaft Center Support Bearing Parts and Q&A

Center Bearing
5161435AA
Q: How to Install a Driveshaft Center Support Bearing on Dodge Charger?
A:
Before installing the driveshaft center support bearing, drop the propeller shaft rear segment into a press so that it rests on the joint yoke. After that, place the bearing assembly over the shaft. C-4735 installer uses: Place the assembled bearings onto the shaft. When the propeller shaft comes out of the press, fasten boot 1 to the section at the rear of the shaft. The propeller shaft spline interface uses a "skip-tooth" shape so that there is only one correct way to assemble it and avoid problems with balance. Line up the blue marks you noticed while taking the frames apart and then match the front section to the rear section. Next, install boot 2 onto the first area, making sure it goes into groove 3. After that, put the propeller shaft back into your vehicle.
Center Bearing
5014097AA
Q: How to Service and Repair a Driveshaft Center Support Bearing for HD on Dodge Ram 1500?
A:
To service the driveshaft center support bearing, take out the rear propeller shaft and place marks on the rear and front propeller shafts for future reference. After that, take off the slip joint boot clamp, move the boot down from the boot collar and divide the two shafts. Insert Position Bearing Splitter Tool 1130 in the gap of the propeller shaft and driveshaft center support bearing, then add Bridge 938 to the tool to remove the driveshaft center support bearing. Place the driveshaft center support bearing and boot collar over the shaft, followed by using Installer 1346448A to set the driveshaft center support bearing and boot collar. Grease both the inner and outer splines on the shaft, place the two halves against one another and slide the whole system into place. Next, put the slip yoke boot onto the boot collar and secure it with the boot clamp and lastly install the propeller shaft to the vehicle. Since launch shudder is caused by initial acceleration, decrease the driveshaft center support bearing height by 3.0 mm (0.125 inch) at a time using shim stock or plates and not washers and use bolts with the correct length.