How to Service and Repair a Brake Caliper on 2000 Chrysler Sebring?

Open the car by first removing the drive shaft from the front brake. After that, place the special tool into the front hub assembly following the shown example. With the pads out, test the hub torque to discover the brake drag torque which will help you calculate brake drag force once the pads are installed. Screw the nuts firmly to keep the disc secure on the hub. Get the pad clip securely on the caliper support, then tidy up the piston and carefully install it in the cylinder, being careful not to harm the piston boot when fitting the other elements of the caliper. Run the engine and push the brake pedal for 5 seconds, using pressure equivalent to around 196 N (44 lbs.), then turn off the engine and spin the brake disc forward 10 times. Weigh the hub torque on a spring scale and compute the drag torque of the disc brake by taking the difference between the measured hub torque and the starting hub torque. The accepted range for this difference is no higher than 69 N (15.4 lbs.). Should the difference be larger than the limit, remove the piston, check for dirt and watch out for corrosion or wear near the piston ring and on the lock pin and guide pin.

OEM 2000 Chrysler Sebring Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Calipers found

View related parts
2000 Chrysler Sebring Caliper Part Number: MB928410
Product Specifications
- Other Name: Caliper Package, Front Left; Caliper Disc Brake
- Item Weight: 12.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MB928410
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi, LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Chrysler Sebring Caliper, Rear Passenger Side Part Number: MR129584
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Package, Rear Brake; Caliper Disc Brake
- Position: Rear Passenger Side
- Item Weight: 6.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR129584
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Chrysler Sebring Submodels:
- Base, GTC, JX, JXi, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2000 Chrysler Sebring Caliper Assembly, Rear Driver Side Part Number: MR129583
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper; Caliper Package, Rear Brake; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Item Weight: 6.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR129583
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Chrysler Sebring Submodels:
- Base, GTC, JX, JXi, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2000 Chrysler Sebring Caliper Part Number: MB928411
Product Specifications
- Other Name: Brake Caliper; Caliper Package, Front Right; Caliper Disc Brake
- Item Weight: 11.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MB928411
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi, LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Chrysler Sebring Caliper Assembly Part Number: 5011701AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Disc Brake
- Item Weight: 3.90 Pounds
- Item Dimensions: 8.4 x 6.5 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5011701AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Chrysler Sebring Caliper Assembly Part Number: 5011700AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Disc Brake
- Item Weight: 4.00 Pounds
- Item Dimensions: 8.2 x 6.6 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5011700AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Chrysler Sebring Caliper Assembly Part Number: 4856922
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Assembly, Front Wheel Disc Brake Partial, Right; Caliper Disc Brake
- Item Weight: 5.40 Pounds
- Item Dimensions: 7.8 x 7.0 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4856922
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Chrysler Sebring Caliper Assembly Part Number: 4856923
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper; Caliper Assembly, Front Wheel Disc Brake Partial, Right; Caliper Disc Brake
- Item Weight: 5.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4856923
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Chrysler Sebring Submodels:
- JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

2000 Chrysler Sebring Brake Caliper Parts and Q&A

Q: How to Service and Repair a Brake Caliper on 2000 Chrysler Sebring?
A: Open the car by first removing the drive shaft from the front brake. After that, place the special tool into the front hub assembly following the shown example. With the pads out, test the hub torque to discover the brake drag torque which will help you calculate brake drag force once the pads are installed. Screw the nuts firmly to keep the disc secure on the hub. Get the pad clip securely on the caliper support, then tidy up the piston and carefully install it in the cylinder, being careful not to harm the piston boot when fitting the other elements of the caliper. Run the engine and push the brake pedal for 5 seconds, using pressure equivalent to around 196 N (44 lbs.), then turn off the engine and spin the brake disc forward 10 times. Weigh the hub torque on a spring scale and compute the drag torque of the disc brake by taking the difference between the measured hub torque and the starting hub torque. The accepted range for this difference is no higher than 69 N (15.4 lbs.). Should the difference be larger than the limit, remove the piston, check for dirt and watch out for corrosion or wear near the piston ring and on the lock pin and guide pin.