How to Replace a Windshield Washer Nozzle on the Rear on 2002 Jeep Wrangler?

You should remove the three screws on the inside of the liftglass that hold the trim cover and then uncover it. Take the washer supply hose off the barbed nipple attached to the rear washer nozzle. Take the nozzle in one hand and then remove the plastic nut inside the car that holds the threaded nipple of the rear washer nozzle to the liftglass. Take the rear washer nozzle and seal out of the liftglass by removing it from the outside, after putting the nipple through the hole. To install, place the rear washer nozzle against the outside of the liftglass, but, from the cabin interior, secure it by tightening the related nut to 1 Nm (8 in. lbs.). Rebuild the washer supply hose onto the barbed nipple, cover the rear wiper motor from the inside using the trim cover and using a torque of 1 Nm (10 in. lbs.), install and tighten the three screws.

OEM 2002 Jeep Wrangler Windshield Washer Nozzle

Front Windshield Washer Nozzle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Windshield Washer Nozzles found

View related parts
2002 Jeep Wrangler Washer Nozzle, Front Part Number: 55156728AB
$31.29 MSRP: $45.80
You Save: $14.51 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Replaces: 55156728AA
- Item Weight: 0.60 Pounds
- Item Dimensions: 1.0 x 1.2 x 1.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55156728AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Jeep Wrangler Submodels:
- 65th Anniversary Edition, 70th Anniversary, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 2.4L L4, 2.5L L4, 3.8L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2002 Jeep Wrangler Washer Nozzle, Front Part Number: 55154938
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Item Weight: 0.40 Pounds
- Item Dimensions: 1.3 x 1.0 x 1.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 55154938
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Jeep Wrangler Submodels:
- SE, Sahara, Sport, X | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2002 Jeep Wrangler Nozzle Part Number: 4883520AA
Product Specifications
- Other Name: Nozzle - Liftgate Washer; Nozzle Liftgate Washer
- Item Weight: 0.40 Pounds
- Item Dimensions: 1.4 x 1.3 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4883520AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

2002 Jeep Wrangler Windshield Washer Nozzle Parts and Q&A

Q: How to Replace a Windshield Washer Nozzle on the Rear on 2002 Jeep Wrangler?
A: You should remove the three screws on the inside of the liftglass that hold the trim cover and then uncover it. Take the washer supply hose off the barbed nipple attached to the rear washer nozzle. Take the nozzle in one hand and then remove the plastic nut inside the car that holds the threaded nipple of the rear washer nozzle to the liftglass. Take the rear washer nozzle and seal out of the liftglass by removing it from the outside, after putting the nipple through the hole. To install, place the rear washer nozzle against the outside of the liftglass, but, from the cabin interior, secure it by tightening the related nut to 1 Nm (8 in. lbs.). Rebuild the washer supply hose onto the barbed nipple, cover the rear wiper motor from the inside using the trim cover and using a torque of 1 Nm (10 in. lbs.), install and tighten the three screws.