How to Replace a Windshield Washer Nozzle on the Front on Jeep Wrangler?

Before changing the front windshield washer nozzle, open and support the hood. Disconnect the supply hose from the barbed nipple on the front of the washer under the rear hood. Pull the snap features of the front washer and push the nozzle out through the mounting hole on the hood panel, then take the nozzle from its place above the hood panel. Position the front washer nozzle by attaching it from the top of the hood panel into the mark where it should connect, so the two small holes face the windshield. Pinch down the nozzle on the mounting hole and hold it like that until the snap connectors are fully locked. After hooking up the washer supply hose at the front barbed washer nozzle from under the hood, seal the hood and fasten it. After that, use the front waste system to check how the water sprays. If needed, adjust the orifices on the nozzles.

How to Service and Repair a Rear Windshield Washer Nozzle on Jeep Wrangler?

Service the rear windshield washer spray nozzle by taking off the trim cover on the rear wiper motor after prying the wiper arm out from the inside. Take out the supply hose from the barbed nipple where the back washer is connected. With the lift strap pulled all the way back and the hood latch secured to the nozzle, grab the plastic nut inside the liftglass that secures the threaded nipple. Pull the rear washer nozzle nipple through the mounting hole at the back so it's visible on the outside, then remove the nozzle-with the rubber gasket-from the outside. While setting up the rear nozzle, install the rubber gasket surrounding it outside the lift glass. The nozzle should align with the arrowhead on the glass. Fit and tighten the plastic nut inside the liftglass, so that it secures the threaded nipple to it at a torque of 1 N.m (8 in. lbs.). Join the rear washer hose again to the barbed nipple of the rear washer nozzle and place the trim cover over the rear wiper motor hidden behind the liftglass.

OEM Jeep Wrangler Windshield Washer Nozzle

Front Windshield Washer Nozzle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Windshield Washer Nozzles found

View related parts
Jeep Wrangler Washer Nozzle, Front Part Number: 68164356AB
$31.12 MSRP: $45.55
You Save: $14.43 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2017 Jeep Wrangler | 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 6 Cyl 3.6 L GAS
View related parts
Jeep Wrangler Washer Nozzle, Front Part Number: 55156728AB
$31.29 MSRP: $45.80
You Save: $14.51 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Replaces: 55156728AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2012 Jeep Wrangler | 65th Anniversary Edition, 70th Anniversary, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 2.4L L4, 2.5L L4, 3.8L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Washer Nozzle, Front Part Number: 68370210AA
$11.17 MSRP: $16.35
You Save: $5.18 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Nozzle - Washer; Windshield Washer Nozzle, Front; Headlight Washer Nozzle, Front; Nozzle Washer Front Camera; Nozzle Windshield Washer
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon X, Unlimited Sahara, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Willys, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Washer Nozzle, Front Part Number: 68293025AA
$12.77 MSRP: $18.70
You Save: $5.93 (32%)
ADD TO CART
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon X, Unlimited Sahara, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Willys, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Washer Nozzle, Front Part Number: 55154938
Product Specifications
- Other Name: Nozzle - Windshield Washer; Windshield Washer Nozzle, Front; Nozzle Windshield Washer
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2002 Jeep Wrangler | SE, Sahara, Sport, X | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Nozzle Part Number: 4883520AA
Product Specifications
- Other Name: Nozzle - Liftgate Washer; Nozzle Liftgate Washer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Wrangler Windshield Washer Nozzle

Choose OEM Windshield Washer Nozzle that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Windshield Washer Nozzle follows strict manufacturing steps to lock in quality and fit. If your Jeep Wrangler matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Wrangler parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Wrangler Windshield Washer Nozzle Parts and Q&A

Washer Nozzle, Front
55154938
Q: How to Replace a Windshield Washer Nozzle on the Front on Jeep Wrangler?
A:
Before changing the front windshield washer nozzle, open and support the hood. Disconnect the supply hose from the barbed nipple on the front of the washer under the rear hood. Pull the snap features of the front washer and push the nozzle out through the mounting hole on the hood panel, then take the nozzle from its place above the hood panel. Position the front washer nozzle by attaching it from the top of the hood panel into the mark where it should connect, so the two small holes face the windshield. Pinch down the nozzle on the mounting hole and hold it like that until the snap connectors are fully locked. After hooking up the washer supply hose at the front barbed washer nozzle from under the hood, seal the hood and fasten it. After that, use the front waste system to check how the water sprays. If needed, adjust the orifices on the nozzles.
Nozzle
4883520AA
Q: How to Service and Repair a Rear Windshield Washer Nozzle on Jeep Wrangler?
A:
Service the rear windshield washer spray nozzle by taking off the trim cover on the rear Wiper Motor after prying the wiper arm out from the inside. Take out the supply hose from the barbed nipple where the back washer is connected. With the lift strap pulled all the way back and the hood latch secured to the nozzle, grab the plastic nut inside the liftglass that secures the threaded nipple. Pull the rear washer nozzle nipple through the mounting hole at the back so it's visible on the outside, then remove the nozzle-with the rubber gasket-from the outside. While setting up the rear nozzle, install the rubber gasket surrounding it outside the lift glass. The nozzle should align with the arrowhead on the glass. Fit and tighten the plastic nut inside the liftglass, so that it secures the threaded nipple to it at a torque of 1 N.m (8 in. lbs.). Join the rear washer hose again to the barbed nipple of the rear washer nozzle and place the trim cover over the rear wiper motor hidden behind the liftglass.