How to Service and Repair a Drive Shaft on 2006 Jeep Wrangler?

Before attending to the rear propeller shaft, place the vehicle on a hoist in neutral. Place a mark all the way down the shaft and at both ends, for help during installation. Lift the bolts holding the U-joint strap at the pinion shaft yoke and then use a pry tool to ease open the dust boot clamp on the propeller shaft yoke. Move the slip yoke off the transmission/transfer case shaft and remove the propeller shaft from the rear. To connect the slip yoke, slide it onto the transmission/transfer case output shaft, align the marks at the yoke with the propeller shaft and install the shaft afterward. Put the U-joint strap bolts into the axle yoke and tighten them to a torque of 19 Nm (14 ft. lbs.). After that, secure the dust boot to the propeller shaft yoke with the help of the Clamp Tool C-4975A.

OEM 2006 Jeep Wrangler Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Drive Shafts found

View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52098784AD
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52098784AC
- Item Weight: 9.00 Pounds
- Item Dimensions: 19.0 x 3.8 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52098784AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 4 Cyl 2.4 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 56052585AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Item Weight: 15.50 Pounds
- Item Dimensions: 27.3 x 4.1 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56052585AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- Unlimited | 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52853407AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Item Weight: 9.10 Pounds
- Item Dimensions: 19.9 x 4.2 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52853407AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- SE | 4 Cyl 2.4 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52853160AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Item Weight: 10.60 Pounds
- Item Dimensions: 29.8 x 3.5 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52853160AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- Unlimited | 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52098787AD
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52098787AC
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52098787AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited Rubicon, X | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52853410AF
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52853410AB, 52853410AD, 52853410AC
- Item Weight: 15.20 Pounds
- Item Dimensions: 17.3 x 3.9 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52853410AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited Rubicon, X | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52853402AD
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52853402AB
- Item Weight: 21.00 Pounds
- Item Dimensions: 41.5 x 4.4 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52853402AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- SE | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52098377AF
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52098377AE
- Item Weight: 21.10 Pounds
- Item Dimensions: 44.6 x 4.5 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52098377AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited, Unlimited Rubicon, X | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Drive Shaft Part Number: 52853404AG
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52853404AC, 52853404AF, 52853404AB, 52853404AD, 52853404AE
- Item Weight: 26.70 Pounds
- Item Dimensions: 52.0 x 9.4 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52853404AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4.0L V6, 6 Cyl 4.0 L GAS

2006 Jeep Wrangler Drive Shaft Parts and Q&A

Q: How to Service and Repair a Drive Shaft on 2006 Jeep Wrangler?
A: Before attending to the rear propeller shaft, place the vehicle on a hoist in neutral. Place a mark all the way down the shaft and at both ends, for help during installation. Lift the bolts holding the U-joint strap at the pinion shaft yoke and then use a pry tool to ease open the dust boot clamp on the propeller shaft yoke. Move the slip yoke off the transmission/transfer case shaft and remove the propeller shaft from the rear. To connect the slip yoke, slide it onto the transmission/transfer case output shaft, align the marks at the yoke with the propeller shaft and install the shaft afterward. Put the U-joint strap bolts into the axle yoke and tighten them to a torque of 19 Nm (14 ft. lbs.). After that, secure the dust boot to the propeller shaft yoke with the help of the Clamp Tool C-4975A.