How to Install a Steering Knuckle on 2007 Dodge Caliber?

Put the steering knuckle in place by aligning the hub with the splines of the halfshaft outer C/V joint. Secure the knuckle onto the screw, making sure that the hole in the knuckle points over the opening in the stud. Place a new star or ball joint stud pinch bolt and nut, fasten the nut with 82 Nm of torque. When installing the vehicle, do not move the strut assembly-knuckle bolts on the steering knucks, but instead screw on the nuts while holding the bolts in place. Make sure the lower end of the strut is directly below the knuckle's upper end and then line up the holes and use the two bolts to assemble them. Set the nuts on the bolts, then tighten the whole unit to 84 Nm. Insert the outer tie rod ball stud into the knuckle arm, begin fastening the tie rod end-to-knuckle nut onto the stud and tighten the nut to 132 Nm as you hold the tie rod end stud with a wrench. Fit the wheel speed sensor head onto the knuckle, secure it with a screw tightened to 12 Nm and then put the routing clip onto the sensor cable. Fit the brake rotor, disc brake caliper and adapter, after which clean the threads of the halfshaft outer C/V joint. Install the halfshaft's washer and its hub nut at the end and tighten them slightly. With help holding the rotor, secure the hub nut with torque equal to 245 Nm. Pass the cotter pin through the nut and its notches, as well as through the hole in the halfshaft, tighten the nut until the notches match the hole and wrap the ends of the cotter pin tightly around the lock nut. Add the tire and wheel, tighten the nuts to the mounting bolt with 135 Nm of torque and drive the car down from the lift. In the case of the original knuckle, Net-Build can make wheel alignment unnecessary; adjust alignment if it is required.

OEM 2007 Dodge Caliber Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Steering Knuckles found

View related parts
2007 Dodge Caliber Knuckle, Front Passenger Side Part Number: 68088498AD
$398.46 MSRP: $585.00
You Save: $186.54 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Right; Wheel Bearing Kit; Hub Assembly Kit; Knuckle And Hub Front
- Position: Front Passenger Side
- Replaces: 5085702AF, 68088498AC, 68088498AB
- Item Weight: 17.70 Pounds
- Item Dimensions: 8.6 x 11.6 x 14.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088498AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2007 Dodge Caliber Knuckle, Front Passenger Side Part Number: 68088532AB
$297.69 MSRP: $614.00
You Save: $316.31 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Right; Knuckle And Hub Front
- Position: Front Passenger Side
- Replaces: 5105810AF, 5105810AD, 5105810AB, 5105810AA, 68088532AA, 5105810AC, 5105810AE
- Item Weight: 16.50 Pounds
- Item Dimensions: 14.6 x 11.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088532AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2007 Dodge Caliber Knuckle, Front Driver Side Part Number: 68088531AB
$311.37 MSRP: $608.00
You Save: $296.63 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Left; Knuckle And Hub Front
- Position: Front Driver Side
- Replaces: 5105809AE, 5105809AD, 5105809AC, 5105809AA, 5105809AB, 5105809AF, 68088531AA
- Item Weight: 17.80 Pounds
- Item Dimensions: 14.3 x 12.2 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088531AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2007 Dodge Caliber Knuckle, Front Driver Side Part Number: 68088534AB
$267.18 MSRP: $424.00
You Save: $156.82 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Left
- Position: Front Driver Side
- Replaces: 5085707AH, 5085707AI, 5085707AF, 68088534AA, 5085707AJ, 5085707AG, 5085707AK
- Item Weight: 17.10 Pounds
- Item Dimensions: 14.7 x 11.3 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088534AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2007 Dodge Caliber Knuckle, Front Driver Side Part Number: 68088499AD
$398.46 MSRP: $585.00
You Save: $186.54 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Left; Wheel Bearing Kit; Hub Assembly Kit; Knuckle And Hub Front
- Position: Front Driver Side
- Replaces: 5085703AG, 5085703AH, 68088499AC, 68088499AB, 68088499AA, 5085703AI, 5085703AF, 5085703AK, 5085703AJ
- Item Weight: 17.40 Pounds
- Item Dimensions: 14.5 x 11.3 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088499AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2007 Dodge Caliber Knuckle, Front Passenger Side Part Number: 68088533AB
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Right
- Position: Front Passenger Side
- Replaces: 5085704AG, 5085704AI, 5085704AF, 68088533AA, 5085704AJ, 5085704AK, 5085704AH
- Item Weight: 17.20 Pounds
- Item Dimensions: 14.6 x 11.2 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68088533AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Caliber Submodels:
- Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS

2007 Dodge Caliber Steering Knuckle Parts and Q&A

Q: How to Install a Steering Knuckle on 2007 Dodge Caliber?
A: Put the steering knuckle in place by aligning the hub with the splines of the halfshaft outer C/V joint. Secure the knuckle onto the screw, making sure that the hole in the knuckle points over the opening in the stud. Place a new star or ball joint stud pinch bolt and nut, fasten the nut with 82 Nm of torque. When installing the vehicle, do not move the strut assembly-knuckle bolts on the steering knucks, but instead screw on the nuts while holding the bolts in place. Make sure the lower end of the strut is directly below the knuckle's upper end and then line up the holes and use the two bolts to assemble them. Set the nuts on the bolts, then tighten the whole unit to 84 Nm. Insert the outer tie rod ball stud into the knuckle arm, begin fastening the tie rod end-to-knuckle nut onto the stud and tighten the nut to 132 Nm as you hold the tie rod end stud with a wrench. Fit the wheel speed sensor head onto the knuckle, secure it with a screw tightened to 12 Nm and then put the routing clip onto the sensor cable. Fit the brake rotor, disc brake caliper and adapter, after which clean the threads of the halfshaft outer C/V joint. Install the halfshaft's washer and its hub nut at the end and tighten them slightly. With help holding the rotor, secure the hub nut with torque equal to 245 Nm. Pass the cotter pin through the nut and its notches, as well as through the hole in the halfshaft, tighten the nut until the notches match the hole and wrap the ends of the cotter pin tightly around the lock nut. Add the tire and wheel, tighten the nuts to the mounting bolt with 135 Nm of torque and drive the car down from the lift. In the case of the original knuckle, Net-Build can make wheel alignment unnecessary; adjust alignment if it is required.