How to Install an Engine Mount with Mopar Lock and Seal Adhesive for 2WD on 2007 Dodge Durango?

For a 2WD, use Mopar(R) Lock and Seal Adhesive, Medium Strength Threadlocker and secure the engine mount to the engine block and the front axle bolts to the left engine bracket. Start by putting in the engine mount plates on either side of the engine block and tighten their fasteners to 54 Nm (40 ft. lbs.). Place the thru bolts inside the engine mounts and start threading the nuts onto the top of the bolts lightly. Lower the engine with special tool #8534 until all four thru bolts link with their frame brackets. After tightening the thru bolt nuts to 94 Nm (70 ft. lbs.), set the oil drain trough, the engine oil filter, the cooling fan and reattach the negative battery cable. When using a 4WD conversion, also put Mopar(R) Lock and Seal Adhesive, Medium Strength Threadlocker, on the M9 bolts. Install the engine mount brackets on each side of the engine, then fit the engine mounts onto the front axle-virgin nuts should be tightened by 94 Nm (70 ft. lbs.). Lift the front axle onto the frame, install the thru bolts in the left and right sides and tighten the nuts to a torque of 94 Nm (70 ft. lbs.). Put the two high thru bolts into the engine mounts and just start screwing the nuts back on. Using special tool #8534, lower the engine until the engine brackets sit on the thru bolts and line up through holes of the engine mounts and through holes of the left engine bracket with the front axle slots. Lightly bolt the left engine bracket to the front axle and the lower thru bolts. Apply 101 Nm (75 ft. lbs.) of force to the nuts for the thru bolts and the bolts attaching the front axle to the left engine bracket. When that is done, put in the oil drain trough, engine oil filter, install the cooling fan and make sure the negative battery cable is reconnected.

OEM 2007 Dodge Durango Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Engine Mounts found

View related parts
2007 Dodge Durango Front Mount, Rear Part Number: 52021614AA
$51.60 MSRP: $94.95
You Save: $43.35 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Rear; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Insulator Engine Mount
- Position: Rear
- Replaces: 52855458AA
- Item Weight: 6.30 Pounds
- Item Dimensions: 8.0 x 4.9 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021614AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Front Part Number: 52021709AB
$16.67 MSRP: $23.95
You Save: $7.28 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket; Engine Mount, Front; Motor Mount; Valve Grind Gasket Kit; Lower Gasket Kit; Front Insulator; Bracket Engine Mount
- Position: Front
- Item Weight: 5.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021709AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Passenger Side Part Number: 52855588AD
$48.72 MSRP: $67.85
You Save: $19.13 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Right; Engine Mount Bracket; Motor Mount; Front Insulator; Mount; Insulator Engine Mount
- Position: Front Passenger Side
- Replaces: 52855588AC
- Item Weight: 6.00 Pounds
- Item Dimensions: 7.5 x 4.5 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855588AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Passenger Side Part Number: 52021636AB
$23.47 MSRP: $29.75
You Save: $6.28 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Right, Right; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Replaces: 52021636AA
- Item Weight: 2.40 Pounds
- Item Dimensions: 7.3 x 5.4 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021636AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 5.7L V8, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Passenger Side Part Number: 52021638AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Right, Right; Motor Mount; Front Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021638AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Driver Side Part Number: 52021633AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855455AB
- Item Weight: 9.90 Pounds
- Item Dimensions: 5.3 x 6.7 x 7.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021633AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Front Driver Side Part Number: 52021639AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Left, Left; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Front Driver Side
- Replaces: 52021639AA
- Item Weight: 4.30 Pounds
- Item Dimensions: 6.7 x 5.5 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021639AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Driver Side Part Number: 52855589AD
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Left; Engine Mount Bracket; Motor Mount; Front Insulator; Mount; Insulator Engine Mount
- Position: Front Driver Side
- Replaces: 52855589AC
- Item Weight: 7.30 Pounds
- Item Dimensions: 6.6 x 4.7 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855589AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Front Driver Side Part Number: 52122775AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Left, Left; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Front Driver Side
- Replaces: 52021637AB, 52021637AA
- Item Weight: 2.30 Pounds
- Item Dimensions: 24.7 x 15.8 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52122775AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 5.7L V8, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Mount Bracket, Front Part Number: 52021629AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front, Right; Motor Mount; Engine Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Front
- Item Weight: 3.80 Pounds
- Item Dimensions: 6.0 x 5.3 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021629AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Driver Side Part Number: 52021627AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Left; Engine Mount Bracket; Motor Mount; Insulator Engine Mount
- Position: Front Driver Side
- Replaces: 52855453AB
- Item Weight: 2.60 Pounds
- Item Dimensions: 7.9 x 6.2 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021627AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- SLT, ST, SXT | 6 Cyl 3.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Passenger Side Part Number: 52021626AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Right; Engine Mount Bracket; Motor Mount; Insulator Engine Mount
- Position: Front Passenger Side
- Replaces: 52855452AB
- Item Weight: 6.90 Pounds
- Item Dimensions: 6.7 x 6.1 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021626AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- SLT, ST, SXT | 6 Cyl 3.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Passenger Side Part Number: 52021632AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Replaces: 52855454AB
- Item Weight: 7.30 Pounds
- Item Dimensions: 6.7 x 6.5 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021632AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Passenger Side Part Number: 52021610AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Replaces: 52855456AB
- Item Weight: 7.20 Pounds
- Item Dimensions: 7.1 x 6.1 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021610AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Driver Side Part Number: 52021611AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855457AB
- Item Weight: 9.10 Pounds
- Item Dimensions: 8.0 x 7.4 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021611AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Front Mount Part Number: 52021615AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Front
- Replaces: 52855459AA
- Item Weight: 7.80 Pounds
- Item Dimensions: 7.3 x 6.7 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021615AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Passenger Side Part Number: 52855540AE
Product Specifications
- Other Name: Insulator - Engine Mount; Front Right Torque Strut; Mount Bracket; Motor Mount; Rear Insulator; Front Insulator; Mount Insulator; Mount; Insulator Engine Mount
- Position: Passenger Side
- Replaces: 52855540AD, 52855540AC
- Item Weight: 5.90 Pounds
- Item Dimensions: 7.3 x 4.6 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855540AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SE, SLT, SXT | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Durango Front Mount, Driver Side Part Number: 52855539AE
Product Specifications
- Other Name: Insulator - Engine Mount; Front Left Torque Strut Bracket; Motor Mount; Front Insulator; Mount Insulator; Mount; Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855539AC, 52855539AD
- Item Weight: 7.10 Pounds
- Item Dimensions: 6.1 x 5.6 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855539AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SE, SLT, SXT | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS

2007 Dodge Durango Engine Mount Parts and Q&A

Q: How to Install an Engine Mount with Mopar Lock and Seal Adhesive for 2WD on 2007 Dodge Durango?
A: For a 2WD, use Mopar(R) Lock and Seal Adhesive, Medium Strength Threadlocker and secure the engine mount to the engine block and the front axle bolts to the left engine bracket. Start by putting in the engine mount plates on either side of the engine block and tighten their fasteners to 54 Nm (40 ft. lbs.). Place the thru bolts inside the engine mounts and start threading the nuts onto the top of the bolts lightly. Lower the engine with special tool #8534 until all four thru bolts link with their frame brackets. After tightening the thru bolt nuts to 94 Nm (70 ft. lbs.), set the oil drain trough, the engine oil filter, the cooling fan and reattach the negative battery cable. When using a 4WD conversion, also put Mopar(R) Lock and Seal Adhesive, Medium Strength Threadlocker, on the M9 bolts. Install the engine mount brackets on each side of the engine, then fit the engine mounts onto the front axle-virgin nuts should be tightened by 94 Nm (70 ft. lbs.). Lift the front axle onto the frame, install the thru bolts in the left and right sides and tighten the nuts to a torque of 94 Nm (70 ft. lbs.). Put the two high thru bolts into the engine mounts and just start screwing the nuts back on. Using special tool #8534, lower the engine until the engine brackets sit on the thru bolts and line up through holes of the engine mounts and through holes of the left engine bracket with the front axle slots. Lightly bolt the left engine bracket to the front axle and the lower thru bolts. Apply 101 Nm (75 ft. lbs.) of force to the nuts for the thru bolts and the bolts attaching the front axle to the left engine bracket. When that is done, put in the oil drain trough, engine oil filter, install the cooling fan and make sure the negative battery cable is reconnected.