How to Maintain Your Seat Heater on 2008 Chrysler Aspen?

The first step in servicing the seat heater is to remove and separate the battery's negative cable. To work on the seat cushion, remove the matching cover and the center rear console as well. Take out the harness routing clip attached to the console bracket and detach the electrical connector for the inoperative second row seat cushion element. Lift the faulty heating wire from the bent-end cap and cut it right at the edge where the original metal begins. To take out the seat back, separate and remove the battery negative wire, go for the ideal seat back trim cover and extract the inner second row seat back bracket trim cover. Unconnect the inoperative second row seat back powered by electricity and also disconnect the harness routing clip. Finally, cut off the wires from the old heating element so they are flush with the existing heating element. The new heating element goes on top of the factory element and because the older one is permanently attached and can't be taken out without causing damage, you should not try to remove it.

OEM 2008 Chrysler Aspen Seat Heater

Seat Warmer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Seat Heaters found

View related parts
2008 Chrysler Aspen Element Part Number: 68019020AA
Product Specifications
- Other Name: Pad - Heater; Pad Heater Seat Cushion; Pad Heater Cushion
- Item Weight: 1.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68019020AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2008 Chrysler Aspen Submodels:
- Limited, Limited Hybrid | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2008 Chrysler Aspen Element Part Number: 68019019AA
Product Specifications
- Other Name: Pad - Heater; Pad Heater Seat Back
- Item Weight: 0.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68019019AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2008 Chrysler Aspen Submodels:
- Limited, Limited Hybrid | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2008 Chrysler Aspen Seat Cushion Heater, Lower Part Number: 5000013AB
Product Specifications
- Other Name: Seat Heater Pad, Front, Lower; Element; Heater Cushion; Seat Heater
- Position: Lower
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.4 x 7.4 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5000013AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Aspen Submodels:
- Limited, Limited Hybrid | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2008 Chrysler Aspen Seat Back Heater, Upper Part Number: 5000014AA
Product Specifications
- Other Name: Pad; Seat Heater Pad, Front, Upper; Element; Heater Back; Seat Heater
- Position: Upper
- Item Weight: 0.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5000014AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Aspen Submodels:
- Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

2008 Chrysler Aspen Seat Heater Parts and Q&A

Q: How to Maintain Your Seat Heater on 2008 Chrysler Aspen?
A: The first step in servicing the seat heater is to remove and separate the battery's negative cable. To work on the seat cushion, remove the matching cover and the center rear console as well. Take out the harness routing clip attached to the console bracket and detach the electrical connector for the inoperative second row seat cushion element. Lift the faulty heating wire from the bent-end cap and cut it right at the edge where the original metal begins. To take out the seat back, separate and remove the battery negative wire, go for the ideal seat back trim cover and extract the inner second row seat back bracket trim cover. Unconnect the inoperative second row seat back powered by electricity and also disconnect the harness routing clip. Finally, cut off the wires from the old heating element so they are flush with the existing heating element. The new heating element goes on top of the factory element and because the older one is permanently attached and can't be taken out without causing damage, you should not try to remove it.