How is a Crankshaft Installed in an Engine on 2008 Dodge Ram 2500?

Install the main bearings in the block and caps after selecting them, always making sure they are well lubricated. Put the crankshaft into the block and place the thrust washers into it. Before fitting the main bearing caps and bolting them down, oil and clean each cap bolt and tighten them by hand at 27 Nm to start, then again by 90°. Fit each crossbolt with a new washer/gasket and after securing the first one, A, tighten it to 28 Nm (21 ft. lbs.). Check the crankshaft for end play. Attach the connecting rods onto the crankshaft and squeeze the rod bearing caps into place. Fit the timing drive, oil pump, timing chain case cover, rear main seal and retainer, windage tray/oil pan gasket, oil pick-up tube and oil pan. When you have finished both the dry-run and reverse running, add the vibration damper and the engine.

OEM 2008 Dodge Ram 2500 Crankshaft

Crank Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Crankshafts found

View related parts
2008 Dodge Ram 2500 Crankshaft Part Number: 68054213AA
$2989.03 MSRP: $4525.00
You Save: $1535.97 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 5102117AB, 5175555AA, 5102117AA, 68000918AA
- Item Weight: 97.30 Pounds
- Item Dimensions: 41.7 x 10.7 x 9.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68054213AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Dodge Ram 2500 Submodels:
- Laramie, SLT, ST, Sport, TRX4 | 5.9L L6, 6 Cyl 5.9 L DIESEL
View related parts
2008 Dodge Ram 2500 Crankshaft Part Number: 53021302AD
Product Specifications
- Other Name: Crankshft; Crankshaft Includes Tone Ring And Tone Ring Mounting Screws
- Item Weight: 64.00 Pounds
- Item Dimensions: 29.6 x 8.5 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53021302AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 8 Cyl 5.7 L GAS
View related parts
2008 Dodge Ram 2500 Crankshaft Part Number: 68003405AA
Product Specifications
- Item Weight: 154.80 Pounds
- Item Dimensions: 41.9 x 10.8 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68003405AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2008 Dodge Ram 2500 Submodels:
- Laramie, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL

2008 Dodge Ram 2500 Crankshaft Parts and Q&A

Q: How is a Crankshaft Installed in an Engine on 2008 Dodge Ram 2500?
A: Install the main bearings in the block and caps after selecting them, always making sure they are well lubricated. Put the crankshaft into the block and place the thrust washers into it. Before fitting the main bearing caps and bolting them down, oil and clean each cap bolt and tighten them by hand at 27 Nm to start, then again by 90°. Fit each crossbolt with a new washer/gasket and after securing the first one, A, tighten it to 28 Nm (21 ft. lbs.). Check the crankshaft for end play. Attach the connecting rods onto the crankshaft and squeeze the rod bearing caps into place. Fit the timing drive, oil pump, timing chain case cover, rear main seal and retainer, windage tray/oil pan gasket, oil pick-up tube and oil pan. When you have finished both the dry-run and reverse running, add the vibration damper and the engine.