Other Name: Seat Belt - Front Inner; Seat Belt Receptacle, Rear Right; Rear Belt Assembly Buckle; Latch; Front Inner Center Shoulder Belt Buckle; Front Center Seat.
Position: Inner Passenger Side
Replaces: 5HG321D5AD, 5HG321J3AD
Item Weight: 1.20 Pounds
Item Dimensions: 9.4 x 3.4 x 2.9 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 5HG321X9AD
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 3500 Submodels:
Laramie, SLT, ST, SXT, Sport | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
Other Name: Seat Belt - Rear Center Shoulder; Seat Belt Lap and Shoulder Belt, Rear Center; Center Seat Belt; Seat Belt Rear Counter Shoulder; Seat Belt Rear Center Shoulder
Position: Rear Center
Item Weight: 2.70 Pounds
Item Dimensions: 7.2 x 7.2 x 4.0 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 1CG661J3AA
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 3500 Submodels:
Laramie, SLT, ST, SXT, Sport, TRX4 | 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Rear; Rear Belt Assembly; Seat Belt Front Center Shoulder; Seat Belt Front Center; Seat Belt Front
Replaces: 1CG67ZJ3AA
Item Weight: 2.50 Pounds
Item Dimensions: 5.0 x 4.4 x 4.4 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 1CG671J3AB
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 3500 Submodels:
Laramie, SLT, ST, SXT, Sport, TRX4 | 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
| Page 1 of 2 |Next >
1-20 of 33 Results
2008 Dodge Ram 3500 Seat Belt Parts and Q&A
Q: How to Maintain and Fix the Rear Outboard Seat Belt in a Mega Cab on 2008 Dodge Ram 3500?
A: First, check all of the seat belts, buckles, hardware, retractors, tether straps and anchors in the Mega Cab to make sure they are properly in place, working well or undamaged and change any cut, worn, torn or twisted belts, realign warped webbing, tighten loose parts and swap any broken buckles, retractors, latch plates or anchors with copies from the Mopar section of the DaimlerChrysler manual. Connect the inner retractor onto the upper hole located at the C-pillar, so the hooks are engaged with it. Fasten the lower retractor bracket to the C-pillar with a screw that has been tightened to 39 Nm (29 ft. lbs.). Push the belt web guide onto the B-pillar until you hear the clips engage. Put the lower trim onto the C-pillar and ensure you can reach the turning loop from its face and only then install the upper trim. Slide the turning loop of the seat belt onto the upper C-pillar adjuster and attach it with a screw tightened to 39 Nm (29 ft. lbs.). Attach a new trim cover around the turning loop, so that the engagement tabs click in correctly. Set the lower anchor of the seat belt into the mounting hole at the base of the C-pillar and attach it with a screw tightened to 39 Nm (29 ft. lbs.). After that, place the rear seat back into the vehicle.