How to Service and Repair the Fuel Level Sensor on the Left Side Module on Chrysler 300?

Before starting any service on the fuel level sensor on the left side module, let out the fuel pressure. Remove the negative battery cable from its connector. Pump out enough fuel so that the fuel level is fewer than 5/8 of a tank to keep the module lock-rings from spilling during removal. Place a hard nylon tube with a 30° cut on the end in the tank to drain the fuel partway and open the check valve. Push the cover for the front bottom seat back and pull up to take out the lower front seat cushion. Flip over the foam cover above the module access and take the electrical connector off the left module. Mark the orientation point and use tool #9340 to get rid of the left side module lock ring. Raise the bottom of the module enough to tilt the hose so it sits in the tank's left side. Break the electrical link at the bottom of the module to the left side fuel level sensor, as well as at the bottom to the right side. Open the upper part of your module, tip the lower half to one side and let any remaining fuel drain out. Take the wire out of the module and use a screwdriver to break the locking tabs on the level sensor card. Pull the level sensor card straight out and up from the module, cut the electrical wiring and remove the card.

How to Service and Repair the Fuel Level Sensor on the Right Side Module on Chrysler 300?

For service and repairs on the right side fuel level sensor, start by placing the level sending card and locking in the tabs. Guide the wires into the right place and hold the wire harness down using a tie strap. Push the hoses and harness along the fuel tank, placing them over the center hump. Put in the module, position the marks so it fits and hold it in place with the module lock-ring using special tool #9340. Connect the fuel line to the module first, then place the access covers in place under the right side floor pan. Install the fuel return tubes and make certain the wires run correctly; the wire on the level sending card should be connected to the fuel line at the fuel supply module. After this, place the left side module top onto the bottom and wire up the electrical connectors for the right side and left side cards, keeping wiring organized. Install the module a second time, correctly position the marks and secure the module using the module lock-ring and special tool #9340. Attach the electrical connector to the left side module, add the plastic access cover and finally fold the foam pad that covered the access hole back up. Place the rear lower seat cushion, fill the fuel tank, attach the negative battery cable and let the scan tool pressurize the fuel system while you check for leaks.

OEM Chrysler 300 Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Fuel Level Sensors found

View related parts
Chrysler 300 Fuel Gauge Sending Unit Part Number: 68145782AA
$81.97 MSRP: $183.00
You Save: $101.03 (56%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Sender and Hanger Assembly; Fuel Transfer Unit; Fuel Level Sensor; Level Sensor; Module Kit Level Unit
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2019 Chrysler 300 | Base, C, C Luxury, C Platinum, Limited, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler 300 Fuel Gauge Sending Unit Part Number: 68000605AC
$109.28 MSRP: $163.00
You Save: $53.72 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Level Sensor; Module Kit Level Unit
- Replaces: 68000605AA, 68000605AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2019 Chrysler 300 | Base, C, C Luxury, C Platinum, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler 300 Fuel Pump Part Number: 68367539AA
$361.34 MSRP: $548.00
You Save: $186.66 (35%)
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Pump Assembly; Fuel Sending Unit.; Fuel Pump/Level Unit Kit: Fuel Pump Module, Sending Unit, O-Ring.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Chrysler 300 | C, Limited, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler 300 Module - Pickup / Level Unit Part Number: 68494735AB
$236.80 MSRP: $348.00
You Save: $111.20 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: MODULE-PICKUP / LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2023 Chrysler 300 | C, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Module - Fuel Pump/Level Unit Part Number: 68643777AB
$403.04 MSRP: $587.00
You Save: $183.96 (32%)
ADD TO CART
Product Specifications
- Other Name: MODULE-FUEL PUMP/LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2023 Chrysler 300 | C, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS
View related parts
Chrysler 300 Fuel Pump Gasket Part Number: 68304753AA
$32.23 MSRP: $47.75
You Save: $15.52 (33%)
ADD TO CART
Product Specifications
- Other Name: O Ring - Fuel Pump And Level Unit; Fuel Pump Tank Seal; Fuel Pump Seal; Fuel Pump Assembly Seal; Gasket Fuel Pump
- Replaces: 57009306AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2023 Chrysler 300 | Base, C, C Luxury, C Platinum, C SRT8, LX, Limited, S, SRT8, SRT8 Core, Signature Series, Touring, Touring L | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Fuel Pump, Passenger Side Part Number: 5136023AF
$313.84 MSRP: $467.00
You Save: $153.16 (33%)
Product Specifications
- Other Name: Module Kit - Pickup/Level Unit; Fuel Pump and Sender Assembly, Right; Fuel Transfer Unit; Fuel Level Sensor; Fuel Gauge Sending Unit; Module Kit includes Pickup, Sending Unit, Level Unit, and O-Ring.
- Position: Passenger Side
- Replaces: 5136023AB, RL136023AD, RL136023AC, 5136023AD, 5136023AE, 5136023AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2019 Chrysler 300 | Base, C, C Luxury, C Platinum, C SRT8, LX, Limited, S, SRT8, SRT8 Core, Signature Series, Touring, Touring L | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Module - Fuel Pump/Level Unit Part Number: 68367534AC
$325.17 MSRP: $484.00
You Save: $158.83 (33%)
Product Specifications
- Other Name: MODULE-FUEL PUMP/LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2019 Chrysler 300 | C, C Platinum, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler 300 Module - Fuel Pump/Level Unit Part Number: 5136022AM
$438.54 MSRP: $639.00
You Save: $200.46 (32%)
Product Specifications
- Other Name: MODULE-FUEL PUMP/LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chrysler 300 | Base, C, C Luxury, C Platinum, C SRT8, LX, Limited, S, Signature Series, Touring | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler 300 Module - Fuel Pump/Level Unit Part Number: 68103913AF
$424.80 MSRP: $619.00
You Save: $194.20 (32%)
Product Specifications
- Other Name: MODULE-FUEL PUMP/LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2016 Chrysler 300 | SRT8, SRT8 Core | 6.4L V8, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Module - Fuel Pump/Level Unit Part Number: 68102700AE
$420.22 MSRP: $612.00
You Save: $191.78 (32%)
Product Specifications
- Other Name: MODULE-FUEL PUMP/LEVEL UNIT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2016 Chrysler 300 | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6.1L V8

Chrysler 300 Fuel Level Sensor

Choose OEM Fuel Level Sensor that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Fuel Level Sensor follows strict manufacturing steps to lock in quality and fit. If your Chrysler 300 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine 300 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Chrysler 300 cars contain the Fuel Level Sensor whose primary role is indicating that a car needs to be refuelled. This is an electronic device which works efficiently at high temperatures since its power consumption is low though it is able to give good readings. It mainly comprises of a float,an acting rod /and or resistor through which signals to the fuel gauge are sent. Throughout the years of Chrysler 300 production, several designs of the Fuel Level Sensor have been employed and these are generally situated inside the fuel tank or connected to the fuel pump carrier bracket. The above means that while the basic architecture is similar, there can be differences in calibration as well as responses' accuracy. The Fuel Level Sensor is another vital item during the operation of this car since in the event of a malfunction, it can give wrong signals on the level of fuel in the tank, even after the car has been refueled. It is therefore advised that servicing should be done often so as to fix any problem with the Chrysler 300 Fuel Level Sensor.

Chrysler 300 Fuel Level Sensor Parts and Q&A

Fuel Pump Gasket
68304753AA
Q: How to Service and Repair the Fuel Level Sensor on the Left Side Module on Chrysler 300?
A:
Before starting any service on the fuel level sensor on the left side module, let out the fuel pressure. Remove the negative Battery Cable from its connector. Pump out enough fuel so that the fuel level is fewer than 5/8 of a tank to keep the module lock-rings from spilling during removal. Place a hard nylon tube with a 30° cut on the end in the tank to drain the fuel partway and open the check valve. Push the cover for the front bottom seat back and pull up to take out the lower front Seat Cushion. Flip over the foam cover above the module access and take the electrical connector off the left module. Mark the orientation point and use tool #9340 to get rid of the left side module lock ring. Raise the bottom of the module enough to tilt the hose so it sits in the tank's left side. Break the electrical link at the bottom of the module to the left side fuel level sensor, as well as at the bottom to the right side. Open the upper part of your module, tip the lower half to one side and let any remaining fuel drain out. Take the wire out of the module and use a screwdriver to break the locking tabs on the level sensor card. Pull the level sensor card straight out and up from the module, cut the electrical wiring and remove the card.
Module - Fuel Pump/Level Unit
68102700AE
Q: How to Service and Repair the Fuel Level Sensor on the Right Side Module on Chrysler 300?
A:
For service and repairs on the right side fuel level sensor, start by placing the level sending card and locking in the tabs. Guide the wires into the right place and hold the wire harness down using a tie strap. Push the hoses and harness along the fuel tank, placing them over the center hump. Put in the module, position the marks so it fits and hold it in place with the module lock-ring using special tool #9340. Connect the fuel line to the module first, then place the access covers in place under the right side floor pan. Install the fuel return tubes and make certain the wires run correctly; the wire on the level sending card should be connected to the fuel line at the fuel supply module. After this, place the left side module top onto the bottom and wire up the electrical connectors for the right side and left side cards, keeping wiring organized. Install the module a second time, correctly position the marks and secure the module using the module lock-ring and special tool #9340. Attach the electrical connector to the left side module, add the plastic access cover and finally fold the foam pad that covered the access hole back up. Place the rear lower Seat Cushion, fill the fuel tank, attach the negative Battery Cable and let the scan tool pressurize the fuel system while you check for leaks.