How to Maintain and Repair a Brake Master Cylinder Reservoir on Chrysler Pacifica?

Start by cleaning the master cylinder housing and the brake master cylinder reservoir with solvent such as Mopar Brake Parts Cleaner. After removing the reservoir cap, squirt all the brake fluid you can from the reservoir with the syringe. Ensure you do not remove the brake master cylinder reservoir from the master cylinder because this can cause problems. After that, unhook the master cylinder assembly from the power brake vacuum booster and hold the master cylinder in a vise using the flange for the mounting. Insert the right size punch pin into the two holes to remove the pins that hold the reservoir and master cylinder together. Tilt the brake master cylinder reservoir gently sideways as you pull it up to remove it from the seal grommets in the master cylinder housing and after that, take out the two seal grommets. Before putting the master cylinder in your car, install the new sealing grommets and oil the reservoir area. Set the reservoir on top of the grommets and apply pressure as you rock it to help it sit well. Check that the brake master cylinder reservoir is not too high or low, so that it contacts each sealing grommet. After inserting the two retaining pins for the brake master cylinder reservoir into the master cylinder, assemble the master cylinder assembly to the brake booster. Make sure to put the fluid in the reservoir up to the level shown on its side.

How to install a Brake Master Cylinder Reservoir on Chrysler 300?

You should start by putting the new brake fluid reservoir sealing grommets inside the master cylinder housing while installing the brake master cylinder reservoir. Drizzle clean brake fluid on the surface where the reservoir attaches and align the reservoir with the sealing grommets. Rock and push it down at the same time until the reservoir is set in place. After the hole is drilled, check that the top of both sealing grommets is in contact with the fluid reservoir. After that, add the reservoir mount screw and torque it to 28 Nm or 250 in. lbs. The wiring arrives at the fluid sensor mounted inside the brake fluid reservoir. Place clean and fresh Mopar(R) Brake Fluid or an alternative into the master cylinder reservoir. After that, put in the access panel over the cowl at the top of the engine. Before starting the vehicle, you need to feel a firm brake pedal; if that doesn't happen, drain and recheck the brake system for any leaks. Check the brakes by taking the vehicle out on a short trip.

OEM Chrysler Brake Master Cylinder Reservoir

Brake Fluid Storage Tank

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Brake Master Cylinder Reservoirs found

View related parts
Chrysler Reservoir Tank Part Number: 68004709AB
$40.39 MSRP: $60.15
You Save: $19.76 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
- Replaces: 68004709AA
Fits the following Chrysler Models:
- 200 | 2011-2014 | LX, Limited, S, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
- Sebring | 2007-2010 | Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Reservoir - Brake Master Cylinder Part Number: 68372581AB
$43.82 MSRP: $65.15
You Save: $21.33 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BRAKE MASTER CYLINDER
- Replaces: 68372581AA
Fits the following Chrysler Models:
- Pacifica | 2017-2024 | Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus | 3.6L V6, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020 | 3.6L V6
View related parts
Chrysler Reservoir Tank Part Number: 68144350AA
$55.18 MSRP: $82.10
You Save: $26.92 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Master Cylinder Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Town & Country | 2012-2016 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Reservoir Tank Part Number: 68002154AB
$72.79 MSRP: $103.00
You Save: $30.21 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Master Cylinder Reservoir; Switch; Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Pacifica | 2007-2008 | Base, LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
- Town & Country | 2008-2016 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Master Cylinder Part Number: 68048549AB
$42.08 MSRP: $62.60
You Save: $20.52 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Brake Reservoir; Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder; Brake Master Cylinder
- Replaces: 68048549AA
Fits the following Chrysler Models:
- 300 | 2009-2023 | Base, C, C Luxury, C Platinum, C SRT8, LX, Limited, S, SRT8, SRT8 Core, Signature Series, Touring, Touring L | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler Reservoir Part Number: 5142504AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir Cap; Brake Master Cylinder Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- PT Cruiser | 2006-2010 | Base, Classic, Couture Edition, GT, LX, Limited, Street Cruiser, Touring | 4 Cyl 2.4 L GAS
View related parts
Chrysler Master Cylinder Reservoir Part Number: 68033787AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- 300 | 2008 | C, C SRT8, LX, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Master Cylinder Reservoir Part Number: 5179927AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder Includes Brake Fluid Level Switch; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Aspen | 2007-2009 | Limited, Limited Hybrid | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
Chrysler Reservoir Part Number: 5139150AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- 300 | 2005-2007 | Base, C, C SRT8, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Reservoir Part Number: 5098042AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Crossfire | 2004-2008 | Base, Limited, SRT-6 | 6 Cyl 3.2 L GAS
View related parts
Chrysler Reservoir Tank Part Number: 5072386AA
Product Specifications
- Other Name: Brake Master Cylinder; Brake Master Cylinder Reservoir; Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Pacifica | 2004-2006 | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
- Town & Country | 2001-2007 | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2001-2003 | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View More
View related parts
Chrysler Reservoir Part Number: 5015150AA
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- PT Cruiser | 2001-2005 | Base, Dream, Dream Cruiser, GT, Limited, Street Cruiser, Touring | 4 Cyl 2.4 L GAS
View related parts
Chrysler Reservoir Tank Part Number: 4797630
Product Specifications
- Other Name: Reservoir - Master Cylinder; Reservoir Package, Master Cylinder; Reservoir Brake Master Cylinder
Fits the following Chrysler Models:
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
- Town & Country | 1996-2000 | Base, LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2000 | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View More
View related parts
Chrysler Reservoir Tank Part Number: 4762595
Product Specifications
- Other Name: Reservoir; Reservoir Brake Master Cylinder (Service In Master Cylinder)
Fits the following Chrysler Models:
- Sebring | 1996-2000 | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Master Cylinder Reservoir Part Number: 4761942
Product Specifications
- Other Name: Reservoir - Brake Master Cylinder.; Reservoir; Reservoir Assembly , (Serviced In Item #7); Reservoir Brake Master Cylinder; Reservoir, 1995-96
Fits the following Chrysler Models:
- Prowler | 2001-2002 | Base | 6 Cyl 3.5 L GAS

Chrysler Brake Master Cylinder Reservoir

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Brake Master Cylinder Reservoir for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Brake Master Cylinder Reservoir is where the pressurized fluid is kept to ensure that each pedal application is predictable in giving the car predictable stopping power. In 1925, Chrysler began with vehicles that were firm and could not shake to pieces when applied on the uneven roads. The Floating Power mounts applied by Chrysler to reduce engine shake provided the company with smooth hands and quiet cabins to drivers. Chrysler followed this with the jaw-boning Airflow shape that proved to combine the daring appearance with cooler air within the cabin. Chrysler continued to accelerate hitting the road with the new minivan, spacious seating, easy access, and straightforward prices of the new vehicle to the busy family. Drivers preferred larger cabins, smoother rides, and controls that were where the hands were inclined to go. Reasonable purchasing maintained the popularity, as engineering still could be affordable. The continuous improvements on ride quality and utility supported the image of cars that are good in everyday grind. Brake Master Cylinder Reservoir is the hydraulic bank of the braking system made of tough molded nylon, sealed by tight O-rings and divided into two circuits so that its failure in one half does not eliminate pressure in the other, reducing panic range in case one of the failed parts fails. Brake Master Cylinder Reservoir pumps clean fluid through each line, eliminating any pedal fade and maintaining clamp force through stop-and-go traffic. Brake Master Cylinder Reservoir is moisture-resistant but requires a regular change of the fluid before water sneaks inside and rusts the parts. Brake Master Cylinder Reservoir is compatible with single-thread or multi-thread caps throughout the line, which means that a single replacement part is suitable and keeps all pedals in their places.

Chrysler Brake Master Cylinder Reservoir Parts and Q&A

Reservoir Tank
5072386AA
Q: How to Maintain and Repair a Brake Master Cylinder Reservoir on Chrysler Pacifica?
A:
Start by cleaning the master cylinder housing and the brake master cylinder reservoir with solvent such as Mopar Brake Parts Cleaner. After removing the reservoir cap, squirt all the brake fluid you can from the reservoir with the syringe. Ensure you do not remove the brake master cylinder reservoir from the master cylinder because this can cause problems. After that, unhook the master cylinder assembly from the power brake vacuum booster and hold the master cylinder in a vise using the flange for the mounting. Insert the right size punch pin into the two holes to remove the pins that hold the reservoir and master cylinder together. Tilt the brake master cylinder reservoir gently sideways as you pull it up to remove it from the seal grommets in the master cylinder housing and after that, take out the two seal grommets. Before putting the master cylinder in your car, install the new sealing grommets and oil the reservoir area. Set the reservoir on top of the grommets and apply pressure as you rock it to help it sit well. Check that the brake master cylinder reservoir is not too high or low, so that it contacts each sealing grommet. After inserting the two retaining pins for the brake master cylinder reservoir into the master cylinder, assemble the master cylinder assembly to the brake booster. Make sure to put the fluid in the reservoir up to the level shown on its side.
Master Cylinder
68048549AB
Q: How to install a Brake Master Cylinder Reservoir on Chrysler 300?
A:
You should start by putting the new brake fluid reservoir sealing grommets inside the master cylinder housing while installing the brake master cylinder reservoir. Drizzle clean brake fluid on the surface where the reservoir attaches and align the reservoir with the sealing grommets. Rock and push it down at the same time until the reservoir is set in place. After the hole is drilled, check that the top of both sealing grommets is in contact with the fluid reservoir. After that, add the reservoir mount screw and torque it to 28 Nm or 250 in. lbs. The wiring arrives at the fluid sensor mounted inside the brake fluid reservoir. Place clean and fresh Mopar(R) Brake Fluid or an alternative into the master cylinder reservoir. After that, put in the access panel over the cowl at the top of the engine. Before starting the vehicle, you need to feel a firm brake pedal; if that doesn't happen, drain and recheck the brake system for any leaks. Check the brakes by taking the vehicle out on a short trip.