How to Install Air Bag Sensors for Front and Side Impact on Chrysler Pacifica?

Fix the sensor in the front of the vehicle and plug in connector 4 from the sensor. Insert the front impact sensor 2 into the opening for the headlamp assembly and secure it by adding the two screws 1 from the board to the back of the sensor. Tighten the screws to 8.5 Nm (75 in. lbs.). Then, insert the new front lamp unit on the side with the sensor and do not connect the battery cable yet so you don't get hurt from using an unchecked system. Close the top of the engine compartment. Install the sensor located on the first row B-pillar, place position sensor 1 in the car and link it to electrical connector 3. After fitting the two retaining screws 2 to the impact sensor 1, tightening them to 7 Nm (62 in. lbs.), put the B-pillar lower trim in place on the affected side, but keep the battery negative cable disconnected. Pull the hood back down. To set up the side impact sensors on the second row C-pillars, mount sensor 3 and link electrical connector 1 with electrical connector 2. Attach the two retaining screws 2 to the impact sensor 3 and tighten them to 7 Nm (62 in. lbs.). Then attach the side quarter trim panel, but before connecting the negative battery cable. Put the hood back down.

How to Service an Air Bag Sensor for Front Impact on Chrysler Pacifica?

To work on the front impact sensor, first open the hood, remove the battery negative cable and let the system reserve capacitor discharge for two minutes. Reach over to the side opposite the sensor and pull out the headlamp unit. Pull out the mounting screws for the front impact sensor from the opening in the headlamp, then disconnect the electrical cable to take the sensor out of the vehicle. To set up, simply place the new sensor and attach the electrical connector. Get the two mounting screws back into the headlamp opening, set them to 8.5 Nm (75 in. lbs.) and put the headlamp back into position. You should complete the negative cable connection after the positive cable to prevent possible occupant injuries or death. Check that the vehicle and system operate properly before locking the hood.

OEM Chrysler Pacifica Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Air Bag Sensors found

View related parts
Chrysler Pacifica Impact Sensor, Front Part Number: 4671779AC
$48.02 MSRP: $103.00
You Save: $54.98 (54%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Center, Front; Air Bag Sensor; Front Impact Sensor; Side Impact Sensor; Airbag Impact Sensor.
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica SENSOR-ACCELERATION Part Number: 68658329AA
$14.57 MSRP: $22.35
You Save: $7.78 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Front Center Part Number: 68483900AA
$19.92 MSRP: $29.50
You Save: $9.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Center Front, Rear; Air Bag Sensor; Side Impact Sensor; Sensor Acceleration 2ND Row Side Sensor To B Pillar
- Position: Front Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Pressure Sensor, Center Part Number: 68185745AA
$29.19 MSRP: $43.30
You Save: $14.11 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Pressure; Air Bag Impact Sensor, Center; Air Bag Sensor; Front Sensor; Sensor Pressure
- Position: Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Chrysler Pacifica | Hybrid Platinum, Hybrid Premium, LX, Limited, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Pressure Sensor, Center Part Number: 68245077AA
$15.49 MSRP: $22.55
You Save: $7.06 (32%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Pressure; Air Bag Impact Sensor, Center; Air Bag Sensor; Impact Sensor; Front Sensor; Sensor Pressure Front Door; Sensor Pressure
- Position: Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Rear Part Number: 68245079AB
$25.54 MSRP: $37.55
You Save: $12.01 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Rear; Air Bag Sensor; Side Impact Sensor; Sensor Acceleration Side Single Axis; Sensor Acceleration Single Axis; Sensor Acceleration
- Position: Rear
- Replaces: 68245079AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Sensor - Acceleration Part Number: 68658327AA
$8.58 MSRP: $12.40
You Save: $3.82 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR-ACCELERATION
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica SENSOR-ACCELERATION Part Number: 68658328AA
$11.14 MSRP: $16.00
You Save: $4.86 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica SENSOR-PRESSURE Part Number: 68658330AA
$11.89 MSRP: $17.10
You Save: $5.21 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Front Part Number: 68245081AB
$26.16 MSRP: $37.65
You Save: $11.49 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Impact Sensor; Sensor Acceleration Single Axis; Sensor Acceleration Front; Sensor Acceleration
- Position: Front
- Replaces: 68245081AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Rear Center Part Number: 68185746AA
$26.27 MSRP: $37.95
You Save: $11.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Center Rear, Rear; Air Bag Sensor; Sensor Acceleration
- Position: Rear Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Chrysler Pacifica | Hybrid Platinum, Hybrid Premium, LX, Limited, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Front Impact Sensor Part Number: 68230207AA
$28.94 MSRP: $41.85
You Save: $12.91 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Front; Air Bag Sensor; Sensor Acceleration
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Chrysler Pacifica | Hybrid Platinum, Hybrid Premium, LX, Limited, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Front Center Part Number: 68174975AA
$30.57 MSRP: $44.25
You Save: $13.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Center Front; Air Bag Sensor; Sensor Acceleration
- Position: Front Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Chrysler Pacifica | Hybrid Platinum, Hybrid Premium, LX, Limited, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Front Center Part Number: 68245080AB
$33.18 MSRP: $47.70
You Save: $14.52 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Center Front; Acceleration Sensor; Air Bag Sensor; Sensor; 2ND Row Side Sensor To B Pillar; Dual Axis Acceleration Sensor.
- Position: Front Center
- Replaces: 68245080AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Impact Sensor, Front Part Number: 4896059AA
Product Specifications
- Other Name: Sensor - Air Bag; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Side Sensor; Sensor; Sensor Air Bag
- Position: Front
- Replaces: 4896023AA, 4686957AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 3.5L V6, 3.8L V6, 4.0L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Impact Sensor, Front Part Number: 68483901AA
$15.54 MSRP: $22.60
You Save: $7.06 (32%)
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Impact Sensor; Sensor Acceleration Front Sensor To Front End Module
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)

Chrysler Pacifica Air Bag Sensor

Choose OEM Air Bag Sensor that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Air Bag Sensor follows strict manufacturing steps to lock in quality and fit. If your Chrysler Pacifica matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Pacifica parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Pacifica Air Bag Sensor which is also called the crash sensor is a developer in the improvement of Chrysler Pacifica vehicles safety and efficiencies. This is a small but crucial component, which provides information about an impact in an accident and interacts with the control unit to provide proper activation of air bags and enhance passengers' protection. Exclusively, Chrysler PACIFICA AIR BAG SENSOR is famous for its performance with its ability to work with several PACIFICA cars while preserving the similar mechanism that is substantially focused on correct impact detection. Thus, the Air Bag Sensor is an essential component of the Chrysler Pacifica because it directly impacts the safety features of the car. Lauded as the " Best Minivan of 2016" and the " 2017 North American Utility of the Year," the Chrysler Pacifica Minivan has carved out an impressive position in today's auto market, and this position is reinforced by its Air Bag Sensor performance. Some of the peculiarities of the Chrysler Pacifica Air Bag Sensor are flexibility of the sensor to alter the acceleration pattern depending on the particular collision situation in order to inflate the air bags at the right time for protection of the people inside the car. Hence the Air Bag Sensor adds to the list of efficiency and safety related features that make the Chrysler Pacifica to standout as one of the best cars in its class. All in all, the Chrysler Pacifica Air Bag Sensor is an important component in the vehicle, hence underlining Chrysler's mission of ensuring a safe car.

Chrysler Pacifica Air Bag Sensor Parts and Q&A

Impact Sensor, Front
4671779AC
Q: How to Install Air Bag Sensors for Front and Side Impact on Chrysler Pacifica?
A:
Fix the sensor in the front of the vehicle and plug in connector 4 from the sensor. Insert the front impact sensor 2 into the opening for the headlamp assembly and secure it by adding the two screws 1 from the board to the back of the sensor. Tighten the screws to 8.5 Nm (75 in. lbs.). Then, insert the new front lamp unit on the side with the sensor and do not connect the Battery Cable yet so you don't get hurt from using an unchecked system. Close the top of the engine compartment. Install the sensor located on the first row B-pillar, place position sensor 1 in the car and link it to electrical connector 3. After fitting the two retaining screws 2 to the impact sensor 1, tightening them to 7 Nm (62 in. lbs.), put the B-pillar lower trim in place on the affected side, but keep the battery negative cable disconnected. Pull the hood back down. To set up the side impact sensors on the second row C-pillars, mount sensor 3 and link electrical connector 1 with electrical connector 2. Attach the two retaining screws 2 to the impact sensor 3 and tighten them to 7 Nm (62 in. lbs.). Then attach the side quarter trim panel, but before connecting the negative battery cable. Put the hood back down.
Impact Sensor, Front
4896059AA
Q: How to Service an Air Bag Sensor for Front Impact on Chrysler Pacifica?
A:
To work on the front impact sensor, first open the hood, remove the battery negative cable and let the system reserve capacitor discharge for two minutes. Reach over to the side opposite the sensor and pull out the headlamp unit. Pull out the mounting screws for the front impact sensor from the opening in the headlamp, then disconnect the electrical cable to take the sensor out of the vehicle. To set up, simply place the new sensor and attach the electrical connector. Get the two mounting screws back into the headlamp opening, set them to 8.5 Nm (75 in. lbs.) and put the headlamp back into position. You should complete the negative cable connection after the positive cable to prevent possible occupant injuries or death. Check that the vehicle and system operate properly before locking the hood.