How to Install a Sway Bars on an All-Wheel-Drive on Chrysler Sebring?

If the sway bar kit supports require cushions, insert them onto the bar such that the slit cut in the cushions is accessed. For those with all-wheel surface drive, place the bar over the axle half shafts once you've installed it. After that, place the sway bar kit on the rear crossmember. Put one retainer over each cushion at the holes provided and hold them in place with the retainer screws, but don't tighten them now. On both sides of the vehicle, connect the sway bar kit upper stud to the sway bar link and screw on a nut to that stud, tightening it to 48 Nm (35 ft. lbs.) as you hold the sway bar link stationary. Finally, fasten the cushion retainer screws to 25 Nm or 18 ft. lbs. and bring the vehicle down.

How to Remove and Service a Sway Bars on Chrysler Sebring?

Before dealing with the sway bar kit, make sure to raise and support your vehicle. If fitting, disconnect the engine belly pan, along with the rear and front engine suspension studs. Hold the lower stud on the sway bar link still at both ends, then pull off the nut securing the link to the bar. Remove the two screws holding the power steering hose clamp onto the crossmember and the four screws installing the heat shield over the steering gear. Unscrew the two bolts that hold on the steering gear to the crossmember and hang the steering gear with a bungee cord to stop it from lowering when the crossmember is taken off. Be sure to mark the place of the front crossmember on the body close to each bolt, as off-centered reinstallation may create problems for wheel alignment. Use a transmission jack to stabilize the crossmember, then unscrew the mounting bolts attaching it to the body, as well as the mounting screws connecting the front reinforcement brackets and remove the brackets. Lift the crossmember with the jack just enough that you can remove the sway bar kit without going any higher. Take out the screws that hold the sway bar bushing retainers onto the crossmember, then remove the two sway bar bushing retainers themselves. Open the slit in the cushions to slide both cushions off the sway bar and then remove the bar from your car.

OEM Chrysler Sebring Sway Bars

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Sway Bars found

View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4879266AA
Product Specifications
- Other Name: Bar - Rear Sway; Suspension Stabilizer Bar, Rear; Sway Bar; Bar Rear Sway
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chrysler Sebring | Base, GTC, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4764862AA
Product Specifications
- Other Name: Bar - Rear Sway; Bar Rear Sway
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-1999 Chrysler Sebring | JX, JXi, LX, LXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: 4670526AA
Product Specifications
- Other Name: Bar - Front; Suspension Stabilizer Bar, Front; Sway Bar; Stabilizer Bar Front
- Position: Front
- Replaces: 5105602AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, Limited, LX, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: 4879296AE
Product Specifications
- Other Name: Bar - Front Sway; Suspension Stabilizer Bar, Front; Sway Bar; Bar Front Sway Assembly; Bar Front Sway Bar Only; Bar Front Sway
- Position: Front
- Replaces: 4879296AB, 4879302AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, Limited, LX, LXi, Touring, TSi | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: 4764470AF
Product Specifications
- Other Name: Bar - Front Sway; Suspension Stabilizer Bar, Front; Sway Bar; Bar Front Sway Assembly; Bar Front Sway Bar Only; Bar Front Sway
- Position: Front
- Replaces: 4879341AB, 4764470AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, Limited, LX, LXi, Touring, TSi | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: MR369695
Product Specifications
- Other Name: Bar - Rear Sway; Suspension Stabilizer Bar, Rear; Sway Bar; Bar Rear Sway
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Chrysler Sebring | Base | 4 Cyl 2.4 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: MR369694
Product Specifications
- Other Name: Bar - Rear Sway; Suspension Stabilizer Bar, Rear; Bar Rear Sway
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: MR333618
Product Specifications
- Other Name: Bar - Front Sway; Suspension Stabilizer Bar, Front; Sway Bar; Bar Front Sway
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: MR333616
Product Specifications
- Other Name: Bar - Front Sway; Suspension Stabilizer Bar, Front; Sway Bar; Bar Front Sway
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: MB871885
Product Specifications
- Other Name: Bar Front Sway; Bar, Front Suspension Stabilizer
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chrysler Sebring | LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4879267AA
Product Specifications
- Other Name: Bar - Rear Sway; Suspension Stabilizer Bar, Rear; Sway Bar; Bar Rear Sway
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Stabilizer Bar Part Number: 4656009
Product Specifications
- Other Name: Bar; Sway Bar; Stabilizer Assembly; Bar Front Sway
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4766029AB
Product Specifications
- Other Name: Bar - Rear Suspension; Sway Bar; Bar Rear Sway
- Position: Rear
- Replaces: 4766029AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Sebring | LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 68065515AA
Product Specifications
- Other Name: Bar - Rear Suspension; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Replaces: 5171181AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited, LX, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4670516AA
Product Specifications
- Other Name: Bar - Rear Suspension; Suspension Stabilizer Bar, Rear; Sway Bar; Stabilizer Bar Rear Suspension
- Position: Rear
- Replaces: 5272653AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, Limited, LX, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Rear Part Number: 4670519AA
Product Specifications
- Other Name: Bar - Rear Suspension; Suspension Stabilizer Bar, Rear; Sway Bar; Stabilizer Bar Rear Suspension
- Position: Rear
- Replaces: 5105702AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, Limited, LX, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Stabilizer Bar, Front Part Number: 4670524AA
Product Specifications
- Other Name: Bar - Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: 5272644AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited, LX, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS

Chrysler Sebring Sway Bars

Choose OEM Sway Bars that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Sway Bars follows strict manufacturing steps to lock in quality and fit. If your Chrysler Sebring matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sebring parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Chrysler Sebring Sway Bars Parts and Q&A

Stabilizer Bar, Rear
4670516AA
Q:
How to Install a Sway Bars on an All-Wheel-Drive on Chrysler Sebring?
A:
If the sway bar kit supports require cushions, insert them onto the bar such that the slit cut in the cushions is accessed. For those with all-wheel surface drive, place the bar over the axle half shafts once you've installed it. After that, place the sway bar kit on the Rear Crossmember. Put one retainer over each cushion at the holes provided and hold them in place with the retainer screws, but don't tighten them now. On both sides of the vehicle, connect the sway bar kit upper stud to the sway bar link and screw on a nut to that stud, tightening it to 48 Nm (35 ft. lbs.) as you hold the sway bar link stationary. Finally, fasten the cushion retainer screws to 25 Nm or 18 ft. lbs. and bring the vehicle down.
Stabilizer Bar, Front
4670526AA
Q:
How to Remove and Service a Sway Bars on Chrysler Sebring?
A:
Before dealing with the sway bar kit, make sure to raise and support your vehicle. If fitting, disconnect the engine belly pan, along with the rear and front engine suspension studs. Hold the lower stud on the sway bar link still at both ends, then pull off the nut securing the link to the bar. Remove the two screws holding the power steering hose clamp onto the crossmember and the four screws installing the heat shield over the steering gear. Unscrew the two bolts that hold on the steering gear to the crossmember and hang the steering gear with a bungee cord to stop it from lowering when the crossmember is taken off. Be sure to mark the place of the front crossmember on the body close to each bolt, as off-centered reinstallation may create problems for wheel alignment. Use a transmission jack to stabilize the crossmember, then unscrew the mounting bolts attaching it to the body, as well as the mounting screws connecting the front reinforcement brackets and remove the brackets. Lift the crossmember with the jack just enough that you can remove the sway bar kit without going any higher. Take out the screws that hold the sway bar bushing retainers onto the crossmember, then remove the two sway bar bushing retainers themselves. Open the slit in the cushions to slide both cushions off the sway bar and then remove the bar from your car.