How to Remove and Replace a Brake Master Cylinder on Chrysler Town & Country?

To change the brake master cylinder on a vehicle driven from the left side of the road, pump down the power brake boost vacuum by pressing the brake pedal 4-5 times with the engine off until the pedal becomes firm. Release the negative and positive terminals, take the cover off the battery, loosen the nut and clamp that keep the battery secured to the tray and finally take it out. Always clean all surfaces in the brake fluid reservoir and master cylinder with Mopar(R) Brake Parts Cleaner or another type of solvent. Remove the wiring harness plug from the brake fluid level switch inside the master cylinder reservoir and then take out both brake tube ends from the master cylinder, filling the empty brake tube ports with sealing plugs. Rub the solvent over the section of the power brake booster that meets the master cylinder to clean it. Pull out the two bolts securing the master cylinder to the power brake booster and draw the master cylinder out in one go. Any time the vacuum seal on the mounting flange of the master cylinder is removed, it must be replaced. Pull the old seal off without any sharp instruments so you don't damage it.

How to Install a Brake Master Cylinder on Chrysler Town & Country?

You should first bench bleed the brake master cylinder before putting it onto the car. Wipe down the area on the power brake booster that the vacuum seal from the master cylinder will come into contact with, to prevent cleaner or debris getting into the booster. If no new vacuum seal is already installed on the master cylinder flange, then install a new one; if only, install the new seal instead, ensuring it fits right in its channel. Fit the master cylinder (1) on the studs of the power brake booster (2), so the booster push rod matches the master cylinder piston. Place two Master Cylinder Nut and tighten each one to 25 Nm. Be sure that the primary and secondary brake tube nuts at the master cylinder are not so tight that they touch other parts and leave enough room for the flexible tube sections when the ABS ICU and master cylinder move against each other. Attach the main and helper brake tubes (2 and 3) on their respective ports in the master cylinder, gripping them as you tighten the nuts to 14 Nm. Link the wiring harness connector (2) to the brake fluid level switch (1) inside the brake fluid reservoir and attach the negative battery cable afterward. Fill the reservoir in the master cylinder up to the required line. Firm the brake pedal and then drive the vehicle; if it is loose, drain the fluid from the brakes and search for leaks. At last, check the brakes by driving the car on the road.

OEM Chrysler Town & Country Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Brake Master Cylinders found

View related parts
Chrysler Town & Country Master Cylinder Part Number: 4581491AD
$211.87 MSRP: $316.00
You Save: $104.13 (33%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 4581491AC, 4581491AB, 4581491AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4721550AB
$193.29 MSRP: $355.00
You Save: $161.71 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 4721550AC, 4721550AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4721804AB
$232.05 MSRP: $351.00
You Save: $118.95 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chrysler Town & Country | LX, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4877805AH
$239.06 MSRP: $352.00
You Save: $112.94 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 4877805AE, 4877805AC, 4877805AD, 4877805AG, 4877805AF, 4877805AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring Plus, Walter P. Chrysler Signature Series | 3.3L V6, 3.6L V6, 3.8L V6, 4.0L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4721154AB
$432.64 MSRP: $552.00
You Save: $119.36 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 4721154AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4683264AD
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4294946
Product Specifications
- Other Name: Brake Master Cylinder; Master Cylinder, Complete, W/O Fluid Window; Master Cylinder, Complete
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1995 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4877429AC
Product Specifications
- Other Name: Booster - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2000 Chrysler Town & Country | LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4877270AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chrysler Town & Country | Base, LX, Limited, Touring | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4721565AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Town & Country | EL, EX, LX, LXi, Limited | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4683264
Product Specifications
- Other Name: Master Cylinder - Complete; Master Cylinder Brake Assembly; Master Cylinder Assembly; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Town & Country | Base, LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4509602
Product Specifications
- Other Name: Master Cylinder - Brake - Compensator 21Mm; Brake Master Cylinder; Master Cylinder, Complete
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chrysler Town & Country | Base, Mark Cross | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS
View related parts
Chrysler Town & Country Master Cylinder Part Number: 4721447AB
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Town & Country | EL, EX, LX, LXi, Limited | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS

Chrysler Town & Country Brake Master Cylinder

Choose OEM Brake Master Cylinder that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Master Cylinder follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Brake Master Cylinder in Chrysler Town & Country vehicles is perhaps among the most key parts of the vehicle's braking system that is responsible for translating the pressure exerted by the driver via his foot into hydraulic pressure as a means of controlling the brakes. It works by having pistons enclosed in a cast iron or aluminum body where by it pushes brake fluid to make the slave cylinders act and therefore engage the brakes. Chrysler Town & Country cars have a dual circuit master cylinder most of the times, and this means that if one circuit has a problem, the other can enough breaking power. Through the production of Chrysler Town & Country for some time now, both integral and sometimes external fluid reservoirs for the Brake Master Cylinder have been used and while the latter has been used as a single unit, the former has been known to be either a nylon or a plastic one. This mainly relates to the design and the way they are fastened on the pipeline, which defines the approach to the maintenance and possible leakage. The use of the Brake Master Cylinder is necessary in this regard because safety is of paramount importance and problems such as fluid leaks or internal failure of mechanical components are bound to surface and reduce the braking power of the vehicle and hence the need to inspect it frequently.

Chrysler Town & Country Brake Master Cylinder Parts and Q&A

Master Cylinder
4683264AD
Q: How to Remove and Replace a Brake Master Cylinder on Chrysler Town & Country?
A:
To change the brake master cylinder on a vehicle driven from the left side of the road, pump down the power brake boost vacuum by pressing the brake pedal 4-5 times with the engine off until the pedal becomes firm. Release the negative and positive terminals, take the cover off the battery, loosen the nut and clamp that keep the battery secured to the tray and finally take it out. Always clean all surfaces in the brake fluid reservoir and master cylinder with Mopar(R) Brake Parts Cleaner or another type of solvent. Remove the wiring harness plug from the brake fluid level switch inside the master cylinder reservoir and then take out both brake tube ends from the master cylinder, filling the empty brake tube ports with sealing plugs. Rub the solvent over the section of the power Brake Booster that meets the master cylinder to clean it. Pull out the two bolts securing the master cylinder to the power brake booster and draw the master cylinder out in one go. Any time the vacuum seal on the mounting flange of the master cylinder is removed, it must be replaced. Pull the old seal off without any sharp instruments so you don't damage it.
Master Cylinder
4721804AB
Q: How to Install a Brake Master Cylinder on Chrysler Town & Country?
A:
You should first bench bleed the brake master cylinder before putting it onto the car. Wipe down the area on the power Brake Booster that the vacuum seal from the master cylinder will come into contact with, to prevent cleaner or debris getting into the booster. If no new vacuum seal is already installed on the master cylinder flange, then install a new one; if only, install the new seal instead, ensuring it fits right in its channel. Fit the master cylinder (1) on the studs of the power brake booster (2), so the booster push rod matches the master cylinder piston. Place two Master Cylinder Nut and tighten each one to 25 Nm. Be sure that the primary and secondary brake tube nuts at the master cylinder are not so tight that they touch other parts and leave enough room for the flexible tube sections when the ABS ICU and master cylinder move against each other. Attach the main and helper brake tubes (2 and 3) on their respective ports in the master cylinder, gripping them as you tighten the nuts to 14 Nm. Link the wiring harness connector (2) to the brake fluid level switch (1) inside the brake fluid reservoir and attach the negative battery cable afterward. Fill the reservoir in the master cylinder up to the required line. Firm the brake pedal and then drive the vehicle; if it is loose, drain the fluid from the brakes and search for leaks. At last, check the brakes by driving the car on the road.