How to Maintain and Fix a Control Arm Bushing on Chrysler Town & Country?

To repair the lower control arm rear bushing, you should remove it from the front suspension cradle and secure it in a vise so that you don't damage it. For basic bushings, take a sharp knife and divide the bushing down the middle to remove it from the lower control arm. When replacing hydro bushings, pull out the lower control arm, fix Special Tool 8460 on the hydro-bushing so the Removal Pin, Special Tool 8460-3, comes through the back hole and tighten the Bridge, Special Tool 8460-1, step. To make standard bushings easier to install, use Mopar Silicone Spray Lube inside the hole of the lower control arm rear bushing, slide the bushing until it seats firmly over the upset at the end and then hold the lower control arm firmly in a vice. For hydro bushings, hold the lower control arm in a vise, position the master spline on the bushing inner sleeve at the bottom control arm rear bushing stem and fit the bushing by hand. Place Installer Cup on the bushing and put Bridge over it, then slide Insert, Special Tool 8460-3, through the flange on the lower control arm and slip Bridge inside it. Place a wedge, Special Tool 8460-4, between the flange and the bushing inner sleeve as it comes close to the flange, then screw in the bushing against the wedge, tightening the bridge forcing screw with a torque wrench to 50 Nm (37 ft. lbs.). Don't force it any more, push back the forcing screw, remove the tool and set the new lower control arm into place.

How to Service and Repair a Control Arm Bushing on the Lower Rear on Chrysler Town & Country?

Add some Mopar Silicone Spray Lube or an alternate product to the opening in the rear bushing of the lower control arm to make installation easier. Hold the lower control arm in a vise and install the bushing by pushing and rocking it in place so it goes past the upsetting on the end. When the rear bushing is positioned, you should install the lower control arm back onto the vehicle.

OEM Chrysler Town & Country Control Arm Bushing

Suspension Arm Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Control Arm Bushings found

View related parts
Chrysler Town & Country Lower Control Arm Bushing Part Number: 4684120
$13.54 MSRP: $24.00
You Save: $10.46 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Pivot; Suspension Control Arm Bushing; Control Arm Bushing; Axle Pivot Bushing; Lower Control Arm Front Bushing; Spring Front Bushing; Bushings; Arm, Front Lower Control (LCA) , Right; Bushing Pivot
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, SX, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Lower Control Arm Bushing Part Number: 4743556AA
$24.46 MSRP: $37.90
You Save: $13.44 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Pivot; Suspension Control Arm Bushing; Control Arm Bushing; Axle Pivot Bushing; Lower Control Arm Rear Bushing; Bushings; Bushing Pivot
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, SX, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Control Arm Bushing Part Number: 5272084
$7.36 MSRP: $9.34
You Save: $1.98 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing - Front Suspension Control Arm Pivot; Suspension Control Arm Bushing Kit; Axle Pivot Bushing.; Lower Control Arm Bushing; Front Control Arm and Crossmember Bushings.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1995 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Control Arm Bushing Part Number: 5272098
Product Specifications
- Other Name: Bushing - Front Suspension Control Arm Pivot - Rear; Suspension Control Arm Bushing Kit.; Lower Control Arm Bushing; Rear Bushing for Standard Suspension.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1995 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Lower Control Arm Rear Bushing Part Number: 4743095AA
Product Specifications
- Other Name: Bushing - Pivot; Control Arm Bushing; Axle Pivot Bushing; Bushings; Bushing Lower Control Arm; Bushing Pivot
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS

Chrysler Town & Country Control Arm Bushing

Choose OEM Control Arm Bushing that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Control Arm Bushing follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Town & Country Control Arm Bushing is an important part of the suspension system that is famous for its quality and efficiency for a wide range of Town & Country cars. This is a critical section that is manufactured to act as a flexible link that aims at dampening shock and reducing contact between the control arm and the car structure. The Control Arm Bushing is rather similar to a worn swivel, which enables the control arms to react to road conditions and move according to the input on the steering wheel, while keeping the wheels in their correct position, which is essential for both economy and safety. Rubber, polyurethane and synthetic elastomers - all these are materials used in Chrysler Control Arm Bushing to suit different roads and driver characteristic. The Chrysler Town & Country with lots of space provided by the increased size of wheelbase, including the premier in the segment, the high quality control arm bushings are of great importance. The Control Arm Bushing not only provides better performance to the car but is also is responsible for the safety of passengers because of the wheel alignment. The Chrysler Town & Country Control Arm Bushing presents the automotive market with a superior product that possesses a mix of durability and engineering to give the driver that assurance of a good and safe ride.

Chrysler Town & Country Control Arm Bushing Parts and Q&A

Lower Control Arm Bushing
4743556AA
Q: How to Maintain and Fix a Control Arm Bushing on Chrysler Town & Country?
A:
To repair the lower Control Arm rear bushing, you should remove it from the front suspension cradle and secure it in a vise so that you don't damage it. For basic bushings, take a sharp knife and divide the bushing down the middle to remove it from the lower control arm. When replacing hydro bushings, pull out the lower control arm, fix Special Tool 8460 on the hydro-bushing so the Removal Pin, Special Tool 8460-3, comes through the back hole and tighten the Bridge, Special Tool 8460-1, step. To make standard bushings easier to install, use Mopar Silicone Spray Lube inside the hole of the lower control arm rear bushing, slide the bushing until it seats firmly over the upset at the end and then hold the lower control arm firmly in a vice. For hydro bushings, hold the lower control arm in a vise, position the master spline on the bushing inner sleeve at the bottom control arm rear bushing stem and fit the bushing by hand. Place Installer Cup on the bushing and put Bridge over it, then slide Insert, Special Tool 8460-3, through the flange on the lower control arm and slip Bridge inside it. Place a wedge, Special Tool 8460-4, between the flange and the bushing inner sleeve as it comes close to the flange, then screw in the bushing against the wedge, tightening the bridge forcing screw with a torque wrench to 50 Nm (37 ft. lbs.). Don't force it any more, push back the forcing screw, remove the tool and set the new lower control arm into place.
Lower Control Arm Bushing
4684120
Q: How to Service and Repair a Control Arm Bushing on the Lower Rear on Chrysler Town & Country?
A:
Add some Mopar Silicone Spray Lube or an alternate product to the opening in the rear bushing of the lower Control Arm to make installation easier. Hold the lower control arm in a vise and install the bushing by pushing and rocking it in place so it goes past the upsetting on the end. When the rear bushing is positioned, you should install the lower control arm back onto the vehicle.