How to Remove and Replace a Brake Caliper on an SRT4 for Front on Dodge Caliber?

First, use a brake pedal holding tool to press the brake pedal past its first inch (25 mm) and hold it there to keep the master cylinder from draining brake fluid as you open the lines. After that, hoist the vehicle and take out the wheel mounting nuts and entire tire and wheel assembly. Take out the banjo bolt from where it fastens the brake flex hose to the brake caliper, discard the two washers that are on the bolt and place the banjo bolt to the side. Then, take away the two brake caliper guide pin bolts (2). In the end, disassemble the disc brake caliper (1) by lifting it from the disc brake adapter bracket (3) and the pads, before removing it from the car.

How to Install a Rear Brake Caliper on Dodge Caliber?

Place a wood block over the caliper piston, then work a C-clamp to retract the piston all the way into the bore. Then, place the outboard brake pad onto the caliper, making certain the retaining clip is into place in the spots where the caliper is fully depressed. Put the disc brake caliper onto the bracket, with the better outboard brake pad facing the inboard brake pad and rotor, making sure not to damage the guide pin boots. Remember to replace each guide pin bolt to its original spot to prevent unwanted noise issues, also paying attention to where on the vehicle the special sleeve should be installed by following the build date guide. Place the adapter bracket so that the holes of the caliper guide pin bolts are aligned to the holes in the bracket, then install and tighten both guide pin bolts to 43 Nm (32 ft. lbs.). Guide the brake flex hose from the rear through the brake caliper and make sure to tighten the fixing bolt to 15 Nm (133 in. lbs.). From underneath the chassis, snake the brake flex hose into the rear hub bracket and clip it firm. Slide the brake tube nut onto the brake flex hose and tighten the tube with 17 Nm (150 in. lbs.) of torque. Get the wheel and tire into place and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), then bring the vehicle down and free the brake pedal holding tool. Carry out brake bleeding when needed and go on a road test, braking regularly to make the new brake linings sit in place.

OEM Dodge Caliber Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Brake Calipers found

View related parts
Dodge Caliber Caliper, Rear Passenger Side Part Number: 5191268AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Front Driver Side Part Number: 5191239AA
$113.04 MSRP: $171.00
You Save: $57.96 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Rear Driver Side Part Number: 68020261AB
$125.07 MSRP: $188.00
You Save: $62.93 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Rear Driver Side Part Number: 5191267AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Front Passenger Side Part Number: 5191238AA
$130.02 MSRP: $181.00
You Save: $50.98 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Rear Passenger Side Part Number: 68020252AB
$108.84 MSRP: $145.00
You Save: $36.16 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Replaces: 68020252AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper Part Number: 68033077AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper Assembly Disc Brake Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper Part Number: 68033076AA
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper; Caliper Assembly Disc Brake Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Front Driver Side Part Number: 68032699AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Caliper, Front Passenger Side Part Number: 68032698AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS

Dodge Caliber Brake Caliper

Choose OEM Brake Caliper that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Caliper follows strict manufacturing steps to lock in quality and fit. If your Dodge Caliber matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Caliber parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

It is an article that is used in Dodge Caliber vehicles in the braking system to guarantee secure performance on the road. This Brake Caliper is characterized by the ability to clamp the brake pads against the rotors stopping the rotation of the wheels and improving the braking force of the vehicle. Being offered as either fixed or floating types, the Dodge Caliber Brake Caliper suits a variety of Caliber models to respond to customers' driving experiences. There are calipers that have a fixed connection to the pistons on both sides of the rotor and these as are more efficient than floating callipers although the latter are much commoner and easier to maintain. As for the Dodge Caliber brake caliper, this is an important detail that can provide an excellent fuel economy and even wear of the pads that can become a problem if the caliper sticks. It is essential to carry out an inspection and maintenance of the Brake Caliper on your Dodge Caliber in the right manner periodically. Specifically, there is the Dodge Caliber Brake Caliper that may boast a durable build and universality of the product with various models of Caliber that amplify the driving experience. As a reputable brand for car parts, the product beneficial to the performance of Dodge Caliber Brake Caliper and at the same time promoting the safety of the drivers and individuals in the car. In conclusion, the Dodge Caliber Brake Caliper can be said as one of the most important components of the Dodge vehicle's Braking system, which reflects the quality and high performances of Dodge brand.

Dodge Caliber Brake Caliper Parts and Q&A

Caliper, Front Passenger Side
5191238AA
Q: How to Remove and Replace a Brake Caliper on an SRT4 for Front on Dodge Caliber?
A:
First, use a brake pedal holding tool to press the brake pedal past its first inch (25 mm) and hold it there to keep the master cylinder from draining brake fluid as you open the lines. After that, hoist the vehicle and take out the wheel mounting nuts and entire tire and wheel assembly. Take out the banjo bolt from where it fastens the brake flex hose to the brake caliper, discard the two washers that are on the bolt and place the banjo bolt to the side. Then, take away the two brake caliper guide pin bolts (2). In the end, disassemble the disc brake caliper (1) by lifting it from the disc brake adapter bracket (3) and the pads, before removing it from the car.
Caliper, Rear Driver Side
5191267AA
Q: How to Install a Rear Brake Caliper on Dodge Caliber?
A:
Place a wood block over the caliper piston, then work a C-clamp to retract the piston all the way into the bore. Then, place the outboard Brake Pad onto the caliper, making certain the retaining clip is into place in the spots where the caliper is fully depressed. Put the disc brake caliper onto the bracket, with the better outboard brake pad facing the inboard brake pad and rotor, making sure not to damage the guide pin boots. Remember to replace each guide pin bolt to its original spot to prevent unwanted noise issues, also paying attention to where on the vehicle the special sleeve should be installed by following the build date guide. Place the adapter bracket so that the holes of the caliper guide pin bolts are aligned to the holes in the bracket, then install and tighten both guide pin bolts to 43 Nm (32 ft. lbs.). Guide the brake flex hose from the rear through the brake caliper and make sure to tighten the fixing bolt to 15 Nm (133 in. lbs.). From underneath the chassis, snake the brake flex hose into the rear hub bracket and clip it firm. Slide the brake tube nut onto the brake flex hose and tighten the tube with 17 Nm (150 in. lbs.) of torque. Get the wheel and tire into place and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), then bring the vehicle down and free the brake pedal holding tool. Carry out brake bleeding when needed and go on a road test, braking regularly to make the new brake linings sit in place.