How to Install an A/C Clutch on Dodge Charger?

Gently push the field coil toward the compressor so that the dowel pin placed at the back of the coil is inside the hole in the A/C compressor's front, checking that the wire is not being squeezed. A new snap ring needs to hold the compressor clutch field coil on the A/C compressor, so the bevel side faces out and the eyelets line up with either the left or right edges of the dowel pin. Snap Ring Pliers 9764 or an equivalent tool can be used to place the snap ring that fastens the compressor field coil after you ensure the ring is fully in the right groove. Prevent untimely contact with the friction plate by not harming the pulley and bearing assembly. Repeat with fitting the pulley and bearings onto the compressor; use a block of wood to gently tap them on if you find it hard to get them in place. A new snap ring needs to be used to bind the pulley and bearing together, with the bevel showing from the outside. Again, using Snap Ring Pliers 9764 or an equivalent, set the snap ring that holds the pulley and bearing assembly in place and make sure it is completely seated. If you are exchanging the original clutch plate and pulley and bearing assembly, fit the original shim(s) onto the compressor shaft; if using miethod "If you need to reinstall the old clutch plate and pulley and bearing assembly, put back the shims that came with the compressor and align water pump and crankshaft using the standard shims from your engine which are 2.54mm thick. Gently place the clutch plate onto the compressor's front and put the bolt through it, turning it until it reaches 19 Nm. After the tightening, inspect the air gap in many different places, turning the pulley a little before making the final check. A blade-type feeler gauge should be your choice for model air gaps of 0.35 - 0.60 mm, regardless of clutch recess. Rout the wire from the compressor clutch coil behind the connector bracket, snap the connector onto the bracket, match up the engine wire harness to the connector, install the accessory drive belt, add the radiator fan and shroud assembly and for 5.7L and 6.1L engine vehicles, install the air cleaner housing and air intake hose, after which reconnect the negative battery cable.

How to Remove and Replace an A/C Clutch on Dodge Charger?

The first step is to disconnect and isolate the negative battery cable to remove and replace the compressor clutch. On vehicles with 5.7L and 6.1L engines, take away the air intake hose and air filter housing, then the radiator fan and its housing. After that, remove the accessory drive belt and unplug the engine wire harness from the compressor clutch field coil connector at the top of the A/C compressor. For some models, it is necessary to take out the A/C compressor to replace the shaft bolt or pulley and field coil snap rings, yet the refrigerant system can still be full. Remove the clutch field coil connector and its wire lead from the connector bracket by being careful. Take out the compressor shaft bolt after holding the clutch plate in place with a band-type oil filter wrench or strap wrench. Be sure not to pry on the clutch plate and pulley assembly, as this could harm the plate and watch out for any shim(s) you find so that you can use them again. Very gently rap the clutch plate with a plastic mallet to set it free from the compressor shaft and then take off the clutch plate and the shim(s). Grab Snap Ring Pliers 9764 or comparable device, pull the snap ring loose from the front of the compressor and then extract the pulley and bearing assembly. You should again use Snap Ring Pliers 9764 or similar tools to remove the snap ring binding the compressor clutch field coil to the A/C compressor, before taking out the field coil.

OEM Dodge Charger A/C Clutch

Air Conditioning Clutch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 A/C Clutches found

View related parts
Dodge Charger Clutch Kit Part Number: 68068755AA
$24.33 MSRP: $83.65
You Save: $59.32 (71%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Repair Kit; A/C Compressor Clutch Overhaul Kit includes snap rings, washers, screws, and bolts.
- Replaced by: 68068755AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, R/T, SE, SRT8 | 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Clutch Coil Part Number: 5003681AA
$186.95 MSRP: $279.00
You Save: $92.05 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Clutch; Coil; Coil A/C Clutch; A/C Compressor Clutch
- Replaces: 5072863AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Clutch Coil Part Number: 68242651AA
$266.26 MSRP: $396.00
You Save: $129.74 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Coil; Coil A/C Clutch; A/C Compressor Clutch
- Replaces: 68058043AA, 68058043AC, 68058043AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, SE, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 68232396AC
$257.19 MSRP: $380.00
You Save: $122.81 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; Clutch Kit; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley
- Replaced by: 68232396AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | GT, GT Plus, Pursuit, SE, SXT, SXT Plus, SXT Plus Leather | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Clutch Kit Part Number: 5140428AA
$4.56 MSRP: $36.75
You Save: $32.19 (88%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Package - A/C Compressor; A/C Compressor Clutch; Hardware Kit; Clutch Overhaul Kit A/C Compressor with Snap Rings, Washers, Screws, Pulley Bolt.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010, 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Clutch Coil Part Number: 68232393AA
$171.08 MSRP: $257.00
You Save: $85.92 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Coil; Coil A/C Clutch; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | GT, GT Plus, Pursuit, SE, SXT, SXT Plus, SXT Plus Leather | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Coil - A/C Clutch Part Number: 5140461AB
$122.73 MSRP: $257.00
You Save: $134.27 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: COIL-AIR CONDITIONING CLUTCH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, R/T, SE, SRT8 | 5.7L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 68084834AC
$256.06 MSRP: $379.00
You Save: $122.94 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley
- Replaces: 68084834AB, 68084834AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, R/T, SE, SRT8 | 5.7L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Clutch Kit Part Number: 68032119AA
$41.78 MSRP: $61.40
You Save: $19.62 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Package - A/C Compressor; A/C Compressor Clutch; Repair Kit; Clutch Overhaul Kit A/C Compressor with essential hardware components.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Charger | Pursuit, R/T, SE | 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Clutch Coil Part Number: 68232389AD
$160.59 MSRP: $243.00
You Save: $82.41 (34%)
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; Coil
- Replaced by: 68232389AE
- Replaces: 68232389AA, 68232389AC, 68232389AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | Daytona, Daytona 392, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 5179340AB
$299.82
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; A/C Compressor Clutch Pulley; A/C Compressor Clutch; Clutch Plate & Hub Assembly
- Replaces: 5179340AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Pursuit, SE, SXT | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Dodge Charger Clutch Kit Part Number: 68232388AD
$279.57 MSRP: $423.00
You Save: $143.43 (34%)
ADD TO CART
Product Specifications
- Other Name: Clutch - A/C Compressor; Repair Kit; Compressor Hardware Kit
- Replaced by: 68232388AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | Daytona, Daytona 392, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 68232392AC
$282.88 MSRP: $430.00
You Save: $147.12 (35%)
ADD TO CART
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; Clutch Kit; Clutch & Pulley; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley
- Replaced by: 68232392AD
- Replaces: 68232392AA, 68232392AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | Daytona, Daytona 392, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 68084274AB
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Serpentine Belt Drive Kit; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Replaces: 68084274AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, SE, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 5140426AA
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; A/C Compressor Clutch Pulley; Clutch Plate & Hub Assembly; Pulley; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Daytona R/T, Pursuit, R/T, SRT8 | 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Clutch Part Number: 5140427AA
Product Specifications
- Other Name: Clutch Package - A/C Compressor; A/C Compressor Clutch; Clutch Overhaul Kit A/C Compressor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010, 2007 Dodge Charger | Base, SE | 6 Cyl 2.7 L GAS
View related parts
Dodge Charger Clutch Coil Part Number: 68000489AC
Product Specifications
- Other Name: Coil - A/C Clutch
- Replaces: 68000489AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Base, Pursuit, SE, SXT | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 68018353AA
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Clutch Plate & Hub Assembly; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Charger | Base, Pursuit, SE, SXT | 6 Cyl 3.5 L GAS
View related parts
Dodge Charger Hub Assembly Part Number: 5179519AA
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; A/C Compressor Clutch Pulley; Clutch Plate & Hub Assembly; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Base, SE | 6 Cyl 2.7 L GAS

Dodge Charger A/C Clutch

Choose OEM A/C Clutch that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each A/C Clutch follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The A/C Clutch is one of the flag products of Dodge that has consistently proven anew means of providing reliability and performance, or a means of conditioning the Charger's interior depending on the model in question. Essentially, this A/C Clutch is privileged with the responsibility of engaging the A/C compressor, thereby converting and transferring energy from the engine towards achieving a cool climate within the car. The Dodge charger A/C clutch comes into play when the A/C system is on and it cools the car with so much ease without imposing on the engines task once turned off. Besides increasing the efficiency of the vehicle, this functionality acts also as one of the safety features that can prevent overheating of the engine or any kinds of problems with the A/C system. Thus, the A/C Clutch exemplifies versatility with regard to the Dodge Charger, ranging from the classics to the modern generations. The characteristics of the Dodge Charger A/C Clutch include high production standards owing to its construction materials and the efficiency of the engagement mechanisms in the automotive market. Thus, these features contribute to the proper functioning of the A/C Clutch depending on the driving conditions and make this product guarantees to be perfect for the Charger's lovers. Being a major component in the comfort as well as the performance of the car, Dodge Charger A/C Clutch has remained a key part of Charger and adds to the charger's claim to fame as one of the most remarkable vehicles in the Dodge automobiles.

Dodge Charger A/C Clutch Parts and Q&A

Clutch Kit
5140428AA
Q: How to Install an A/C Clutch on Dodge Charger?
A:
Gently push the field coil toward the compressor so that the dowel pin placed at the back of the coil is inside the hole in the A/C compressor's front, checking that the wire is not being squeezed. A new snap ring needs to hold the compressor clutch field coil on the A/C compressor, so the bevel side faces out and the eyelets line up with either the left or right edges of the dowel pin. Snap Ring Pliers 9764 or an equivalent tool can be used to place the snap ring that fastens the compressor field coil after you ensure the ring is fully in the right groove. Prevent untimely contact with the friction plate by not harming the pulley and bearing assembly. Repeat with fitting the pulley and bearings onto the compressor; use a block of wood to gently tap them on if you find it hard to get them in place. A new snap ring needs to be used to bind the pulley and bearing together, with the bevel showing from the outside. Again, using Snap Ring Pliers 9764 or an equivalent, set the snap ring that holds the pulley and bearing assembly in place and make sure it is completely seated. If you are exchanging the original clutch plate and pulley and bearing assembly, fit the original shim(s) onto the compressor shaft; if using miethod "If you need to reinstall the old clutch plate and pulley and bearing assembly, put back the shims that came with the compressor and align water pump and crankshaft using the standard shims from your engine which are 2.54mm thick. Gently place the clutch plate onto the compressor's front and put the bolt through it, turning it until it reaches 19 Nm. After the tightening, inspect the air gap in many different places, turning the pulley a little before making the final check. A blade-type feeler gauge should be your choice for model air gaps of 0.35 - 0.60 mm, regardless of clutch recess. Rout the wire from the compressor clutch coil behind the connector bracket, snap the connector onto the bracket, match up the engine wire harness to the connector, install the accessory Drive Belt, add the radiator fan and shroud assembly and for 5.7L and 6.1L engine vehicles, install the air cleaner housing and air intake hose, after which reconnect the negative Battery Cable.
Clutch Coil
5003681AA
Q: How to Remove and Replace an A/C Clutch on Dodge Charger?
A:
The first step is to disconnect and isolate the negative Battery Cable to remove and replace the compressor clutch. On vehicles with 5.7L and 6.1L engines, take away the air intake hose and air filter housing, then the radiator fan and its housing. After that, remove the accessory Drive Belt and unplug the engine wire harness from the compressor clutch field coil connector at the top of the A/C compressor. For some models, it is necessary to take out the A/C compressor to replace the shaft bolt or pulley and field coil snap rings, yet the refrigerant system can still be full. Remove the clutch field coil connector and its wire lead from the connector bracket by being careful. Take out the compressor shaft bolt after holding the clutch plate in place with a band-type oil filter wrench or strap wrench. Be sure not to pry on the clutch plate and pulley assembly, as this could harm the plate and watch out for any shim(s) you find so that you can use them again. Very gently rap the clutch plate with a plastic mallet to set it free from the compressor shaft and then take off the clutch plate and the shim(s). Grab Snap Ring Pliers 9764 or comparable device, pull the snap ring loose from the front of the compressor and then extract the pulley and bearing assembly. You should again use Snap Ring Pliers 9764 or similar tools to remove the snap ring binding the compressor clutch field coil to the A/C compressor, before taking out the field coil.