How to Safely Remove an Oxygen Sensor from an Engine on Dodge Charger?

Two heating oxygen sensors are positioned in each exhaust manifold. It is important not to grease the oxygen sensor electrical connector or try to solder the sensor wiring harness. Besides, since the exhaust manifold, exhaust pipes and catalytic converter get very hot as the engine runs, make sure the engine is cooled before you start the oxygen sensor removal process. Don't hold onto the wire directly when you pull the sensor's connector apart. Take out the negative battery cable from its connection first and then raise and hold the vehicle properly. After that, unplug the heated oxygen sensor electrical connector and use a Snap-On YA8875 or a crow foot wrench to pull the oxygen sensor free.

How to Ensure Proper Installation and Avoid Driveability Issues When Replacing an Oxygen Sensor on Dodge Charger?

When putting in a new O2 Sensor, memory in the PCM RAM should be cleared, either by disconnecting the PCM C-1 connector or by temporarily removing the Battery negative terminal, to prevent problems with driveability. Don't use grease on the oxygen sensor electrical connector and never try to solder the sensor wire harness. There are two oxygen sensors, each heated, located in the exhaust manifolds in the vehicle's engine. When removing the sensor, clean the exhaust manifold using an 18 mm X 1.5 + 6E tap. Should you reuse the original sensor, put a small amount of anti-seize compound, for example Loctite 771-64, onto the sensor threads; sensors purchased new already have the coating. Turn the sensor screw to 41 Nm (30 ft. lbs.) with a torque wrench, hook up the electrical cable from the heated oxygen sensor, bring the car down to the ground and connect the negative battery cable.

OEM Dodge Charger Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Oxygen Sensors found

View related parts
Dodge Charger Oxygen Sensor, Front Passenger Side Part Number: 5149180AB
$123.50 MSRP: $182.00
You Save: $58.50 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right, Rear, Rear Left, Rear Right; Oxygen Sensor; includes upstream and downstream sensors for both driver and passenger sides.
- Position: Front Passenger Side
- Replaces: 5149180AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Part Number: 56029050AA
$77.38 MSRP: $114.00
You Save: $36.62 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Right, Rear, Rear Left, Rear Right; Rear Oxygen Sensor; Front Oxygen Sensor; Lower Oxygen Sensor; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Dodge Charger | Pursuit, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Passenger Side Part Number: 56028994AB
$79.61 MSRP: $119.00
You Save: $39.39 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right; Front Oxygen Sensor; Upper Oxygen Sensor; Sensor Oxygen
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Daytona R/T, Pursuit, R/T, SRT8 | 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Driver Side Part Number: 56029049AA
$97.32 MSRP: $144.00
You Save: $46.68 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right, Rear, Rear Left, Rear Right; Rear Oxygen Sensor; Front Oxygen Sensor; Upper Oxygen Sensor; Lower Oxygen Sensor; Sensor Oxygen
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2012 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Driver Side Part Number: 68203458AA
$91.13 MSRP: $138.00
You Save: $46.87 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left; Air / Fuel Ratio Sensor; Air-Fuel Ratio Sensor; Air/Fuel Sensor; Front Oxygen Sensor; Driver Side Upstream Before Catalytic.
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Part Number: 5149171AB
$129.16 MSRP: $190.00
You Save: $60.84 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right, Rear, Rear Left, Rear Right; Oxygen Sensors: Front, Rear, Upper, Lower, Passenger/Driver Side, Before/After Catalytic Converter.
- Position: Front
- Replaces: 5149171AA, 68066160AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Driver Side Part Number: 68500303AA
$122.41 MSRP: $185.00
You Save: $62.59 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left, Front Right; Front Oxygen Sensor; Upper Oxygen Sensor
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Charger | SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Charger Oxygen Sensor Part Number: 68545116AA
$132.51 MSRP: $200.00
You Save: $67.49 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Front Oxygen Sensor; Upper Oxygen Sensor
- Replaces: 68500306AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Charger | SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Passenger Side Part Number: 68144248AD
$76.49 MSRP: $115.00
You Save: $38.51 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left, Front Right, Rear, Rear Right; Oxygen Sensors: Front, Rear, Lower, Passenger Side Upstream/Downstream, Driver Side Downstream.
- Position: Front Passenger Side
- Replaces: 68144248AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2023 Dodge Charger | Daytona, Pursuit, R/T, R/T Road & Track, SE, SRT8 | 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Oxygen Sensor Part Number: 5234921
$56.30 MSRP: $71.36
You Save: $15.06 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1985-1987 Dodge Charger | 2.2, Base, Shelby | 4 Cyl 2.2 L GAS
View related parts
Dodge Charger Oxygen Sensor, Front Passenger Side Part Number: 68250166AA
$92.11 MSRP: $138.00
You Save: $45.89 (34%)
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Right; Front Oxygen Sensor; Upstream Passenger Side Before Catalytic.
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2023 Dodge Charger | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS

Dodge Charger Oxygen Sensor

Choose OEM Oxygen Sensor that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Oxygen Sensor follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The oxygen sensor in many makes of cars including the Dodge charger is a device that calculates the amount of oxygen in the exhaust system. This sensor feeds other information to the Engine Control Unit (ECU), specifically the correct air fuel mixture to maximize the performance of the engine and at the same time reduce pollution of the environment. Thus, the Oxygen Sensor is a crucial element that needs to be replaced on time because its malfunction causes many problems, such as fluctuations in an engine's performance and increased emissions. Dodge Charger models have used various forms of Oxygen Sensors, most widely used are the zirconia and titania Sensors. Zirconia sensors are quite common with particular offering in the narrow-band type and wide-band types for precise fuel control systems. On the other hand, titania sensors work on the basis involving the change of resistance as opposed to voltage. Knowledge of these distinctions is helpful to sustain the performance of the Dodge Charger's engine and to meet the requirements of emissions regulation.

Dodge Charger Oxygen Sensor Parts and Q&A

Oxygen Sensor, Front Passenger Side
56028994AB
Q: How to Safely Remove an Oxygen Sensor from an Engine on Dodge Charger?
A:
Two heating oxygen sensors are positioned in each Exhaust Manifold. It is important not to grease the oxygen sensor electrical connector or try to solder the sensor wiring harness. Besides, since the exhaust manifold, exhaust pipes and Catalytic Converter get very hot as the engine runs, make sure the engine is cooled before you start the oxygen sensor removal process. Don't hold onto the wire directly when you pull the sensor's connector apart. Take out the negative Battery Cable from its connection first and then raise and hold the vehicle properly. After that, unplug the heated oxygen sensor electrical connector and use a Snap-On YA8875 or a crow foot wrench to pull the oxygen sensor free.
Oxygen Sensor, Front
56029050AA
Q: How to Ensure Proper Installation and Avoid Driveability Issues When Replacing an Oxygen Sensor on Dodge Charger?
A:
When putting in a new O2 Sensor, memory in the PCM RAM should be cleared, either by disconnecting the PCM C-1 connector or by temporarily removing the Battery negative terminal, to prevent problems with driveability. Don't use grease on the oxygen sensor electrical connector and never try to solder the sensor wire harness. There are two oxygen sensors, each heated, located in the Exhaust Manifolds in the vehicle's engine. When removing the sensor, clean the exhaust manifold using an 18 mm X 1.5 + 6E tap. Should you reuse the original sensor, put a small amount of anti-seize compound, for example Loctite 771-64, onto the sensor threads; sensors purchased new already have the coating. Turn the sensor screw to 41 Nm (30 ft. lbs.) with a torque wrench, hook up the electrical cable from the heated oxygen sensor, bring the car down to the ground and connect the negative Battery Cable.