How to Service and Repair a Brake Proportioning Valve on Dodge Dakota?

Start by removing the wire from the pressure differential switch and the rear brake lines from the combination valve for Brake Proportioning/Combination Valve servicing. Eliminate the bolt fixing the combination valve and then come out with the valve. When installing, fit the valve onto the bracket and tighten the bolt to 20 - 27 Nm for brakes without ABS and to 10 - 13 Nm for ABS cars. After that, join the brake lines to the combination valve and tighten the bolts to 19 Nm (170 inch lbs.). After that, reattach the wire to the pressure differential switch and bleed the braking system.

How to Maintain and Fix a Brake Proportioning Valve on Dodge Dakota?

To work on the Brake Proportioning/Combination Valve, remove the wire from the pressure differential switch and the rear brake lines from the combination valve. Get rid of the bolt that attaches the combination valve to the hose and take the valve off. During installation, place the combination valve onto the bracket, then tighten the mounting bolt to 20-27 Nm (15-20 ft. lbs.). However, if ABS is installed, tighten to 10-13 Nm (7-10 ft. lbs.). After that, connect the brake lines to the combination valve and tighten them up until they reach 19 Nm (about 170 inch lbs.). After all the repairs, put the wire back to the pressure differential switch and bleed the brake system.

OEM Dodge Dakota Brake Proportioning Valve

Proportioning Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Brake Proportioning Valves found

View related parts
Dodge Dakota Control Valve Part Number: 5015425AA
Product Specifications
- Other Name: Valve - Proportioning; Brake Proportioning Valve; ABS Modulator Valve; ABS Control Module; Pressure Metering Valve; Valve; Valve Proportioning
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001 Dodge Dakota | Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Combination Valve Part Number: 5011623AA
Product Specifications
- Other Name: Valve - Proportioning; Brake Proportioning Valve; Pressure Limiter Valve; Valve; Valve Proportioning
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2002 Dodge Dakota | Base, R/T, SLT, SXT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS

Dodge Dakota Brake Proportioning Valve

Choose OEM Brake Proportioning Valve that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Proportioning Valve follows strict manufacturing steps to lock in quality and fit. If your Dodge Dakota matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Dakota parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Brake Proportioning Valve is an important part which largely improves the braking system and increases the dependability in Dodge Dakota automobiles. It skillfully controls the fluid pressure supply to avoid the rear drum brakes from locking prior to the front disc brakes during a panic stop, which helps in enhancing control of the car and safety. The Brake Proportioning Valve therefore has the responsibility of directing pressures within brake circuits to ensure that these elements increase the general effectiveness of the Dakota's braking system. Suitable for several generations of the Dodge Dakota, this valve is tailored to the requirements of each, starting with the first generation of the Dakota manufactured since 1986 up to later models until the model line was discontinued in 2010. The dependability aspect is evident from its capacity to deliver the intended performance under various driving conditions, thus allowing Dakota's drivers to be confident of a car that will suitably stop as required. Similarly, the Brake Proportioning Valve also has some unique engineering that makes it stands out from other cars on the market it controls the amounts of brake forces to be applied depending on the load and speed of the vehicle. It also helps increase the safety of the cars and also comes as a plus for providing a comfortable drive. All in all, it is for this reason that the Brake Proportioning Valve is retained as a symbol of Dodge's innovative genius and a necessity in Dakota.

Dodge Dakota Brake Proportioning Valve Parts and Q&A

Control Valve
5015425AA
Q: How to Service and Repair a Brake Proportioning Valve on Dodge Dakota?
A:
Start by removing the wire from the pressure differential switch and the rear Brake Lines from the combination valve for Brake Proportioning/Combination Valve servicing. Eliminate the bolt fixing the combination valve and then come out with the valve. When installing, fit the valve onto the bracket and tighten the bolt to 20 - 27 Nm for brakes without ABS and to 10 - 13 Nm for ABS cars. After that, join the brake lines to the combination valve and tighten the bolts to 19 Nm (170 inch lbs.). After that, reattach the wire to the pressure differential switch and bleed the braking system.
Combination Valve
5011623AA
Q: How to Maintain and Fix a Brake Proportioning Valve on Dodge Dakota?
A:
To work on the Brake Proportioning/Combination Valve, remove the wire from the pressure differential switch and the rear Brake Lines from the combination valve. Get rid of the bolt that attaches the combination valve to the hose and take the valve off. During installation, place the combination valve onto the bracket, then tighten the mounting bolt to 20-27 Nm (15-20 ft. lbs.). However, if ABS is installed, tighten to 10-13 Nm (7-10 ft. lbs.). After that, connect the brake lines to the combination valve and tighten them up until they reach 19 Nm (about 170 inch lbs.). After all the repairs, put the wire back to the pressure differential switch and bleed the brake system.