How to Install the Drive Belt on 3.7L/4.7L Engines on Dodge Durango?

First check the condition of all pulleys on a 3.7L/4.7L engine before you install the accessory drive belt. Make sure the serpentine accessory drive belt is installed properly to stop the engine from overheating because the water pump runs backwards. A new belt should be fitted first, not going around the idler pulley (5). Move the tensioner arm until you feel resistance and then put the belt on the idler and allow the tensioner to finish sliding into place on all the belts. After putting the belt on, check the belt wear indicator; it will read no more than 24 mm (0.94 inches) on the 4.7L engine (between tang and housing stop). Should the measurement be beyond the specification, change the serpentine accessory drive belt.

How to Remove and Replace the Drive Belt on 3.7L/4.7L Engines on Dodge Durango?

Always inspect the pulleys first and make sure they are working properly before changing the accessory drive belt on 3.7L/4.7L engines. Putting the serpentine accessory drive belt in the correct place during installation stops the engine from overheating because of a wrongly spinning water pump. Run the new belt over the pulleys except the idler pulley which is positioned between two others (5). When the tensioner strikes its stop point, turn it again until it clicks into the belt, allowing it to sit securely on all pulleys. After the installation is done, watch the belt wear indicator-for 4.7L engines, the gap between the belt's tang and the housing stop (measurement A) should be less than 24 mm (0.94 inches). Should this measurement go outside the specifications, you should replace the serpentine accessory drive belt.

OEM Dodge Durango Drive Belt

Serpentine Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Drive Belts found

View related parts
Dodge Durango Serpentine Belt Part Number: 53010303AC
$69.07 MSRP: $105.00
You Save: $35.93 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Accessory Drive; Serpentine Belt Drive Kit; Drive Belt; V-Belt
- Replaces: 53010303AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2003 Dodge Durango | Base, R/T, SLT, SLT Plus, SXT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5135746AA
$54.45 MSRP: $80.70
You Save: $26.25 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Accessory Drive; Belt Serpentine
- Replaces: 53032125AD, 53032380AE, 53032380AC, 53032380AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Durango | Base, SLT, SLT Plus, SXT, Sport | 4.7L V8, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5184647AB
$40.25 MSRP: $57.85
You Save: $17.60 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, Rallye, SXT, Special Service | 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Serpentine Belt Part Number: 4593852AB
$47.91 MSRP: $68.85
You Save: $20.94 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Serpentine
- Replaces: 4593852AA, 4593665AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Durango | Limited, SE, SLT | 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5184646AC
$41.74 MSRP: $62.10
You Save: $20.36 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Serpentine
- Replaces: 5184646AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Dodge Durango | Citadel, Crew, Express, Heat, SXT, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Serpentine Belt Part Number: 53032817AB
$61.61 MSRP: $89.75
You Save: $28.14 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Accessory Drive; Belt Serpentine
- Replaces: 53032817AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Dodge Durango | Adventurer, Limited, SLT, ST, SXT | 3.7L V6, 4.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5038718AA
$35.27 MSRP: $52.55
You Save: $17.28 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Drive Belt; V-Belt; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2025, 2021 Dodge Durango | SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium | 8 Cyl 6.2 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 68207171AD
$45.06 MSRP: $67.00
You Save: $21.94 (33%)
ADD TO CART
Product Specifications
- Other Name: Belt - Supercharger Drive; Accessory Drive Belt; Serpentine Belt Drive Kit; V-Belt; Supercharger Belt; Belt Supercharger Drive; Drive Belt
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021 Dodge Durango | SRT Hellcat | 8 Cyl 6.2 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5281374AA
$45.62 MSRP: $67.85
You Save: $22.23 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Drive Belt; V-Belt; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2025 Dodge Durango | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, SXT, SXT Plus, Special Service | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 53032805AB
$69.13 MSRP: $104.00
You Save: $34.87 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Accessory Drive; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Dodge Durango | Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 55111074AC
$32.96 MSRP: $48.85
You Save: $15.89 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cap - Coolant Recovery Bottle; Engine, Washer, Radiator Caps; Serpentine & V-Belts; Reservoir Cap; Filler Cap; Reservoir Tank Cap; Recovery Tank Cap; Cap
- Replaces: 55111074AA, 4682828, 5017468AA, 55111074AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2005 Dodge Durango | 3.7L V6, 4.7L V8, 5.2L V8, 5.7L V8, 5.9L V8
View related parts
Dodge Durango Serpentine Belt Part Number: 68519480AA
$45.06 MSRP: $67.00
You Save: $21.94 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Supercharger Drive; Serpentine Belt Drive Kit; Drive Belt; V-Belt; Supercharger Belt
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2025, 2021 Dodge Durango | Citadel, GT, GT Plus, GT Premium, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium, SXT, SXT Plus, Special Service | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 68495977AA
$46.13 MSRP: $62.50
You Save: $16.37 (27%)
ADD TO CART
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Drive Belt; V-Belt
- Replaces: 53013676AB, 53013676AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2025 Dodge Durango | Citadel, GT, Limited, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SXT, Special Service | 5.7L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango Belt - Serpentine Part Number: 68027636AB
$52.48 MSRP: $77.95
You Save: $25.47 (33%)
ADD TO CART
Product Specifications
- Other Name: BELT-SERPENTINE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Durango | Adventurer, Limited, SE, SLT, SXT | 3.7L V6, 4.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 4627031AA
$33.70 MSRP: $48.45
You Save: $14.75 (31%)
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Accessory Drive Belt; Drive Belt; V-Belt; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Limited, R/T, Special Service | 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Serpentine Belt Part Number: 5192067AC
Product Specifications
- Other Name: Belt - Serpentine; Serpentine Belt Drive Kit; Drive Belt; V-Belt; Belt Serpentine
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Durango | Limited Hybrid | 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV)

Dodge Durango Drive Belt

Choose OEM Drive Belt that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Drive Belt follows strict manufacturing steps to lock in quality and fit. If your Dodge Durango matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Durango parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

In Dodge Durango vehicles, the Drive Belt plays an essential role of linking the automobile engine to other parts like the alternator and the 'A/C compressor among others. Normally, there is the serpentine belt used here, go round and connect these components with the crankshaft pulley. This Drive Belt commonly has lifetime of 100 000 miles, however, before this time is achieved it may require replacement if it is worn out for instance by the development of fraying or cracking. Since the inception of Dodge Durango such as the V-belts and the multiple groove belts in the later years that improve on the traction while reducing slippage. The various Drive Belts described above are actually developments of technology which make sure that the Dodge Durango has reliable performance when it comes to power transmission. It needs to be mentioned that the Drive Belt requires regular maintenance, otherwise, it may lead to problems which affect both the parts and the engine.

Dodge Durango Drive Belt Parts and Q&A

Serpentine Belt
53032805AB
Q: How to Install the Drive Belt on 3.7L/4.7L Engines on Dodge Durango?
A:
First check the condition of all pulleys on a 3.7L/4.7L engine before you install the accessory drive belt. Make sure the serpentine accessory drive belt is installed properly to stop the engine from overheating because the Water Pump runs backwards. A new belt should be fitted first, not going around the idler pulley (5). Move the tensioner arm until you feel resistance and then put the belt on the idler and allow the tensioner to finish sliding into place on all the belts. After putting the belt on, check the belt wear indicator; it will read no more than 24 mm (0.94 inches) on the 4.7L engine (between tang and housing stop). Should the measurement be beyond the specification, change the serpentine accessory drive belt.
Serpentine Belt
53032817AB
Q: How to Remove and Replace the Drive Belt on 3.7L/4.7L Engines on Dodge Durango?
A:
Always inspect the pulleys first and make sure they are working properly before changing the accessory drive belt on 3.7L/4.7L engines. Putting the serpentine accessory drive belt in the correct place during installation stops the engine from overheating because of a wrongly spinning Water Pump. Run the new belt over the pulleys except the idler pulley which is positioned between two others (5). When the tensioner strikes its stop point, turn it again until it clicks into the belt, allowing it to sit securely on all pulleys. After the installation is done, watch the belt wear indicator-for 4.7L engines, the gap between the belt's tang and the housing stop (measurement A) should be less than 24 mm (0.94 inches). Should this measurement go outside the specifications, you should replace the serpentine accessory drive belt.