How to Install the ABS Control Module for Antilock Brakes on Dodge Magnum?

Down in the body side rail, gently push unit 1's bracket into the mounting grommets 2. Attach the seal correctly to ABM harness connector 2 prior to fitting it securely into the socket on board ABM 1 and locking the cover into place. After that, fit and tighten the remaining two tubes at hydraulic control unit 4, tightening them to 20 Nm (177 in. lbs.). After that, attach the left 2 and right 3 brake tubes to hydraulic control unit 4, filling them with a tightening torque of 20 Nm (177 in. lbs.). Mount the main 4 and additional 1 brake tubes at hydraulic control unit 7, tightening the tube nuts with 20 Nm (177 in. lbs.) torque. Once the brake holding tool comes off, secure the battery cable 2 to the battery post, making sure it's done the correct way. Finish by filling and partially discharging the braking system and ABS, then run a service test and clear any faults found.

How to Service and Repair the ABS Control Module on Dodge Magnum?

You should remove the battery's negative cable and set it aside before servicing or repairing the Electronic Brake Control Module. After that, push the tabs on both sides of the connector cover and pull down on the lower half until it snaps into place. After closing the cover, take out the connector by pulling it straight away from the antilock brake module. Separate each brake tube from the two routing clips sitting over the upper radiator support and from the routing clip around the fuse and relay area bracket. Open the rear brake tubes from the mounting clip on the bracket. Pull the ICU up, away from the mounting depressions, until you reach the front attaching screws and can work on them easily. Slide the ABM off the HCU and first remove the four screws that fasten them together.

OEM Dodge Magnum ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 ABS Control Modules found

View related parts
Dodge Magnum Control Module Part Number: 68028991AA
$502.66 MSRP: $737.00
You Save: $234.34 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Modulator Valve Part Number: 68028990AA
Product Specifications
- Other Name: Control - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Modulator Part Number: 68002339AA
Product Specifications
- Other Name: Control - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Magnum | R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5134114AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Magnum | R/T, SE, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5134111AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SRT8, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5159192AC
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SRT8, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 68002341AB
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module
- Replaces: 68002341AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Magnum | R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Modulator Part Number: 68004546AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
- Replaces: 5175605AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Magnum | R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5191296AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Module Anti-Lock Brake System
- Replaces: 5159193AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SRT8, SXT, SXT Special Edition | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5175609AE
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module
- Replaces: 5175609AA, 5175609AC, 5175609AD, 5175609AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Magnum | R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 68028992AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Magnum | R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5170344AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Magnum | R/T, SE, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5134113AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SRT8, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5134112AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Magnum | R/T, SE, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Magnum Control Module Part Number: 5136134AC
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Magnum | R/T, SE, SRT8, SXT, SXT Special Edition | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS

Dodge Magnum ABS Control Module

Choose OEM ABS Control Module that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each ABS Control Module follows strict manufacturing steps to lock in quality and fit. If your Dodge Magnum matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Magnum parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Magnum ABS Control Module is one of the crucial life cycle components that signify the efficacy and safety braking among the Dodge Magnum vehicles. They found out that this specific ABS Control Module is essential in preventing wheel lock-up during vigorous braking; hence, improving the vehicle's handling. Together with the ABS modulator, it contributes to the ability to maintain tractive contact with the road hence reducing chances of skidding to the bare minimum. The Dodge Magnum ABS Control Module is a sophisticated assembly of technical gadgets such as wheel speed sensors, valves, pump, and a controller boxed in as Electronic Control Unit that works by altering the amounts of brake pressure to control the braking force in accordance with the information coming in from the sensors. Besides the improvement, of course, of the braking system quality, this complex system also includes additional systems, such as ESC (electronic stability control) and traction control, which helps improve the general security of a car. Appropriate for various Dodge Magnum models, this ABS Control Module is developed specifically for each of the car's modifications - the two-door coupe of the late 1950 - early 1960s, rear-wheel drive sedan since the mid-1960s, and even station wagon in the 1970s. It can indeed be dubbed as a performer in the automotive industry because, with the help of this car model, drivers do not have to worry on constantly experiencing fatal breakdowns or inefficiency of the car's parts and mechanisms since Dodge Magnum has captured the industry's label for quality and endurance. Being an element of the vehicle's brake system, the Dodge Magnum ABS Control Module is the embodiment of the car's primary functions and engagement in the safety mechanisms, which proves its importance as a feature of the Dodge vehicle.

Dodge Magnum ABS Control Module Parts and Q&A

Modulator
68002339AA
Q: How to Install the ABS Control Module for Antilock Brakes on Dodge Magnum?
A:
Down in the body side rail, gently push unit 1's bracket into the mounting grommets 2. Attach the seal correctly to ABM harness connector 2 prior to fitting it securely into the socket on board ABM 1 and locking the cover into place. After that, fit and tighten the remaining two tubes at hydraulic control unit 4, tightening them to 20 Nm (177 in. lbs.). After that, attach the left 2 and right 3 brake tubes to hydraulic control unit 4, filling them with a tightening torque of 20 Nm (177 in. lbs.). Mount the main 4 and additional 1 brake tubes at hydraulic control unit 7, tightening the tube nuts with 20 Nm (177 in. lbs.) torque. Once the brake holding tool comes off, secure the Battery Cable 2 to the battery post, making sure it's done the correct way. Finish by filling and partially discharging the braking system and ABS, then run a service test and clear any faults found.
Control Module
5134111AA
Q: How to Service and Repair the ABS Control Module on Dodge Magnum?
A:
You should remove the battery's negative cable and set it aside before servicing or repairing the Electronic Brake Control Module. After that, push the tabs on both sides of the connector cover and pull down on the lower half until it snaps into place. After closing the cover, take out the connector by pulling it straight away from the antilock brake module. Separate each brake tube from the two routing clips sitting over the upper radiator support and from the routing clip around the fuse and relay area bracket. Open the rear brake tubes from the mounting clip on the bracket. Pull the ICU up, away from the mounting depressions, until you reach the front attaching screws and can work on them easily. Slide the ABM off the HCU and first remove the four screws that fasten them together.