How to Service the Passenger Side Blend Door Actuator on Jeep Grand Cherokee?

Covering and separating the battery negative cable turns off the air bags and then it is good practice to wait two minutes so the air bag system's capacitor discharges and cannot trigger an accidental deployment. On the front of the car, just above the floor panel in the transmission tunnel, sits the actuator which you can only reach by removing the instrument panel or HVAC housing. You should start by uninstalling the glove box door, then the lower I/P glove box door surround panel, the dash assembly and finally the HVAC assembly. Detach the wire harness connector from the blend door actuator, remove the two screws that hold it to the HVAC housing and take away the actuator. Set the blend door actuator into place on the HVAC housing, secure the screws to 2.2 Nm with a Torx wrench, attach the wire harness and put the HVAC unit and instrument panel assembly back into place. With that, switch off the AC and pump new charge into it before connecting the battery negative cable.

How to Install a Blend Door Actuator in a Single Zone Heater-A/C System on Jeep Grand Cherokee?

To install the blend door actuator in a single zone system, secure it by the actuator onto the left side of the HVAC air distribution housing which is found by the passenger seat. Slightly turn the actuator to get the splines on the actuator output shaft and the splines on the blend door cam to line up. Hook up the HVAC wire harness connector to the actuator and tighten the screws holding the actuator onto the housing with 2 Nm (17 in. lbs.). In LHD vehicles, fit the silencer for the instrument panel at the driver side and for RHD vehicles, insert the glove box into the instrument panel. Now attach the negative battery cable again. Stick the blend door actuator in your car, securing it to the correct junction at the right side of the HVAC air distribution housing with the right splines in place. Use two 5 mm screws to attach the actuator to the housing, gently tightening until they reach 2 Nm. After that, link the wire harness connector to the back of the actuator. With LHD models, set the glove box into the instrument panel and on RHD models, set the instrument panel silencer on the left side. In the end, hook the other side of the negative battery cable back up again.

OEM Jeep Grand Cherokee Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Blend Door Actuators found

View related parts
Jeep Grand Cherokee Door Actuator Part Number: 4720279AB
$102.03 MSRP: $151.00
You Save: $48.97 (33%)
ADD TO CART
Product Specifications
- Other Name: Actuator - Heater; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; Actuator; Actuator Heater
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1998 Jeep Grand Cherokee | 5.9 Limited, Base, Laredo, Limited, Orvis, SE, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Grand Cherokee Door Actuator Part Number: 68224186AA
$96.80 MSRP: $147.00
You Save: $50.20 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Blend Door; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; A/C and heater blend doors and recirculation door for driver and passenger.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2022 Jeep Grand Cherokee | 4xe, 75th Anniversary, 80th Anniversary, Altitude, High Altitude, Laredo, Laredo E, Laredo X, Limited, Limited X, Overland, SRT, Summit, Summit Reserve, Trackhawk, Trailhawk, Upland | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Door Actuator, Front Part Number: 68079488AB
$105.17 MSRP: $157.00
You Save: $51.83 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator, Front; HVAC Heater Blend Door Actuator; Actuator; Actuator A/C And Heater
- Position: Front
- Replaces: 68079488AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo, Limited, Overland, Overland Summit, SRT8 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Actuator, Front Part Number: 5143192AA
$112.24 MSRP: $167.00
You Save: $54.76 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door and Heater Blend Door Actuator.; Actuator A/C And Heater
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2010 Jeep Grand Cherokee | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Grand Cherokee Servo Part Number: 5012728AB
$177.43 MSRP: $268.00
You Save: $90.57 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Mode Door; HVAC Defrost, Air Inlet, Heater Blend, and Blend Door Actuator.; Servo Mode Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2004 Jeep Grand Cherokee | Laredo, Limited, Overland, Special Edition, Sport | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Jeep Grand Cherokee Door Actuator Part Number: 68542636AA
$32.09 MSRP: $47.15
You Save: $15.06 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; Actuator
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2025 Jeep Grand Cherokee | 30th Anniversary 4xe, 4xe, Altitude, Altitude X, Anniversary Edition 4xe, Laredo, Laredo X, Limited, Overland, Summit, Summit Reserve, Trailhawk | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Grand Cherokee Door Actuator Part Number: 68565858AB
$38.87 MSRP: $57.05
You Save: $18.18 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; Actuator
- Replaces: 68565858AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2024 Jeep Grand Cherokee | 30th Anniversary 4xe, 4xe, Altitude, Altitude X, Laredo, Laredo X, Limited, Overland, Summit, Summit Reserve, Trailhawk | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Jeep Grand Cherokee Door Actuator, Front Part Number: 68224197AA
$43.65 MSRP: $64.95
You Save: $21.30 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Mode Door; HVAC Floor Mode Door Actuator, Front; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Actuator Mode Door Panel
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2022 Jeep Grand Cherokee | 4xe, 75th Anniversary, 80th Anniversary, Altitude, High Altitude, Laredo, Laredo E, Laredo X, Limited, Limited X, Overland, SRT, Summit, Summit Reserve, Trackhawk, Trailhawk, Upland | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Door Actuator Part Number: 68224192AA
$44.23 MSRP: $64.95
You Save: $20.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Mode Door; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Actuator Mode Door Defrost
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2022 Jeep Grand Cherokee | 4xe, 75th Anniversary, 80th Anniversary, Altitude, High Altitude, Laredo, Laredo E, Laredo X, Limited, Limited X, Overland, SRT, Summit, Summit Reserve, Trackhawk, Trailhawk, Upland | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Servo Part Number: 5137781AA
$39.67 MSRP: $80.35
You Save: $40.68 (51%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Servo - A/C Temperature Door; HVAC Defrost Mode Door Actuator; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2004 Jeep Grand Cherokee | Laredo, Limited, Overland, Special Edition | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Jeep Grand Cherokee Door Part Number: 4886070AB
Product Specifications
- Other Name: Door - Fresh Air Door; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; Actuator; Actuator Fresh Air Door
- Replaces: 4886070AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998 Jeep Grand Cherokee | 5.9 Limited, Laredo, Limited, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Grand Cherokee Door Part Number: 4720569
Product Specifications
- Other Name: Actuator - Heater; HVAC Heater Blend Door Actuator; Actuator; Actuator, Heat And Defrost Door (Mode ) (Aa113800 1362); Actuator, Heat/Defrost Door; Actuator Heater
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1998 Jeep Grand Cherokee | 5.9 Limited, Base, Laredo, Limited, Orvis, SE, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS

Jeep Grand Cherokee Blend Door Actuator

Choose OEM Blend Door Actuator that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Blend Door Actuator follows strict manufacturing steps to lock in quality and fit. If your Jeep Grand Cherokee matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Grand Cherokee parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Grand Cherokee Blend Door Actuator Parts and Q&A

Servo
5012728AB
Q: How to Service the Passenger Side Blend Door Actuator on Jeep Grand Cherokee?
A:
Covering and separating the battery negative cable turns off the air bags and then it is good practice to wait two minutes so the air bag system's capacitor discharges and cannot trigger an accidental deployment. On the front of the car, just above the floor panel in the transmission tunnel, sits the actuator which you can only reach by removing the instrument panel or HVAC housing. You should start by uninstalling the glove box door, then the lower I/P glove box door surround panel, the dash assembly and finally the HVAC assembly. Detach the wire harness connector from the blend door actuator, remove the two screws that hold it to the HVAC housing and take away the actuator. Set the blend door actuator into place on the HVAC housing, secure the screws to 2.2 Nm with a Torx wrench, attach the wire harness and put the HVAC unit and instrument panel assembly back into place. With that, switch off the AC and pump new charge into it before connecting the battery negative cable.
Actuator, Front
5143192AA
Q: How to Install a Blend Door Actuator in a Single Zone Heater-A/C System on Jeep Grand Cherokee?
A:
To install the blend door actuator in a single zone system, secure it by the actuator onto the left side of the HVAC air distribution housing which is found by the passenger seat. Slightly turn the actuator to get the splines on the actuator output shaft and the splines on the blend door cam to line up. Hook up the HVAC wire harness connector to the actuator and tighten the screws holding the actuator onto the housing with 2 Nm (17 in. lbs.). In LHD vehicles, fit the silencer for the instrument panel at the driver side and for RHD vehicles, insert the Glove Box into the instrument panel. Now attach the negative Battery Cable again. Stick the blend door actuator in your car, securing it to the correct junction at the right side of the HVAC air distribution housing with the right splines in place. Use two 5 mm screws to attach the actuator to the housing, gently tightening until they reach 2 Nm. After that, link the wire harness connector to the back of the actuator. With LHD models, set the glove box into the instrument panel and on RHD models, set the instrument panel silencer on the left side. In the end, hook the other side of the negative battery cable back up again.