How to Remove the Side Marker Light on Jeep Liberty?

Disconnect and isolate the negative cable of the battery before proceeding to remove the marker lamp if your car is for the domestic market. After that, pull back the lower section of the liner covering the front of the fender wheel house. Removing the wire harness connector is done on the connector receptacle placed in the back of the front side marker lamp housing in the inside of the outboard-facing front part of the car. The nut attached to the stud under the bottom of the lamp housing should be removed from the front fascia's interior. Last, pull the lower part of the lamp away from the outer side of the fascia and this will lift the tab in the housing out of the notch.

How to Properly Install a Side Marker Light to Avoid Overheating and Damage on Jeep Liberty?

Be sure to pick the correct size and bulb type to install the marker lamp in order not to overheat the lamp, cause harm to the socket or create a wiring issue. It only applies to products built for national consumers since export companies replace the bulb, socket and wiring for the front side marker with a white reflector. Place the base of the bulb where marker bulb socket 2 is, then push the bulb straight into the socket until it is properly seated. Then, put the socket and bulb onto the keyed entry on marker lamp housing 1 on the inside of the outboard-facing front fascia 4 and insert them as far as possible so the socket is secure. Turn the socket to your left a little more than a quarter turn (30 degrees) to secure it in place with the bulb connector pointed below. After you have reconnected wire harness connector 3 to its socket in the bulb, reinstall the front fender wheel house liner. When complete, link the negative cable to the battery once again.

OEM Jeep Liberty Side Marker Light

Side Marker Lamp

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Side Marker Lights found

View related parts
Jeep Liberty Repeater Lamp Part Number: 4806224AE
$25.76 MSRP: $37.70
You Save: $11.94 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Repeater; Turn Signal & Parking Light Lens; Light Assembly; Side Repeater.; Bulbs; Lamp Side Repeater
- Replaces: 4806224AC, 4806224AB, 4806224AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Side Marker Lamp, Driver Side Part Number: 55156883AB
$45.79 MSRP: $67.85
You Save: $22.06 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Marker; Left Side Marker Light Assembly; Turn Signal; Parking Light; Lamp Side Marker; Side Marker Light
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Side Marker Lamp, Driver Side Part Number: 57010213AC
$61.55 MSRP: $92.05
You Save: $30.50 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Marker; Left Side Marker Light Assembly; Turn Signal Light.; Lamp Side Marker
- Position: Driver Side
- Replaces: 57010213AA, 57010213AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Side Marker Lamp, Passenger Side Part Number: 55156882AB
$46.40 MSRP: $67.85
You Save: $21.45 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Marker; Right Side Marker Light Assembly; Turn Signal; Parking Light.; Lamp Side Marker; Side Marker Light
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Side Marker Lamp, Passenger Side Part Number: 57010214AC
$21.45 MSRP: $31.55
You Save: $10.10 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Marker; Right Side Marker Light Assembly; Turn Signal Lights.; Lamp Side Marker
- Position: Passenger Side
- Replaces: 57010214AB, 57010214AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Side Marker Lamp, Front Part Number: 5288895AC
$22.79 MSRP: $32.85
You Save: $10.06 (31%)
ADD TO CART
Product Specifications
- Other Name: Lamp - Side Repeater; Turn Signal Light Assembly, Front; Side Repeater Lamp; Turn Signal Lights; Repeater Lamp; Lamp Side Repeater
- Position: Front
- Replaces: 5288895AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 2.4L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS

Jeep Liberty Side Marker Light

Choose OEM Side Marker Light that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Side Marker Light follows strict manufacturing steps to lock in quality and fit. If your Jeep Liberty matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Liberty parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Liberty Side Marker Light Parts and Q&A

Repeater Lamp
4806224AE
Q: How to Remove the Side Marker Light on Jeep Liberty?
A:
Disconnect and isolate the negative cable of the battery before proceeding to remove the marker lamp if your car is for the domestic market. After that, pull back the lower section of the liner covering the front of the fender wheel house. Removing the wire harness connector is done on the connector receptacle placed in the back of the front side marker lamp housing in the inside of the outboard-facing front part of the car. The nut attached to the stud under the bottom of the lamp housing should be removed from the front fascia's interior. Last, pull the lower part of the lamp away from the outer side of the fascia and this will lift the tab in the housing out of the notch.
Side Marker Lamp, Driver Side
57010213AC
Q: How to Properly Install a Side Marker Light to Avoid Overheating and Damage on Jeep Liberty?
A:
Be sure to pick the correct size and bulb type to install the marker lamp in order not to overheat the lamp, cause harm to the socket or create a wiring issue. It only applies to products built for national consumers since export companies replace the bulb, socket and wiring for the front side marker with a white reflector. Place the base of the bulb where marker bulb socket 2 is, then push the bulb straight into the socket until it is properly seated. Then, put the socket and bulb onto the keyed entry on marker lamp housing 1 on the inside of the outboard-facing front fascia 4 and insert them as far as possible so the socket is secure. Turn the socket to your left a little more than a quarter turn (30 degrees) to secure it in place with the bulb connector pointed below. After you have reconnected wire harness connector 3 to its socket in the bulb, reinstall the front fender wheel house liner. When complete, link the negative cable to the battery once again.