How to Service and Repair a Turn Signal Switch on Jeep Wrangler?

To service and repair the turn signal switch, first disconnect and isolate the battery negative cable. Remove the knee blocker from the instrument panel, then take out the three screws securing the lower steering column shroud to the upper shroud. For vehicles with a standard non-tilt steering column, loosen the two upper steering column mounting nuts; for those with a tilt steering column, move it to the fully lowered position. Remove both the upper and lower shrouds from the steering column. Next, remove the two screws securing the multi-function switch water shield and bracket to the top of the steering column, followed by the one screw located below the multi-function switch control stalk. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column to clear the screw boss below the control stalk. Lift the water shield and bracket with the multi-function switch off the left side of the steering column to access the two wire harness connectors, using the tilt release lever for additional clearance if necessary. Disconnect the two instrument panel wire harness connectors from the multi-function switch connector receptacles and remove the multi-function switch and water shield as a unit. For installation, carefully place the water shield onto the switch, then position the multi-function switch and water shield near their mounts on the steering column. Reconnect the two wire harness connectors, position the multi-function switch onto its mounts, and use the tilt release lever for clearance if needed. Align the lower mounting tab of the water shield bracket with the screw boss below the control stalk, then install and tighten the screw below the control stalk to 1.1 Nm (10 in. lbs.), followed by the two screws at the top of the steering column to 2.2 Nm (20 in. lbs.). Position both upper and lower shrouds onto the steering column and secure the lower shroud to the upper shroud with three screws tightened to 2 Nm (18 in. lbs.). If applicable, tighten the two nuts securing the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs to 22 Nm (200 in. lbs.). Finally, install the knee blocker onto the instrument panel and reconnect the battery negative cable.

OEM Jeep Wrangler Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Turn Signal Switches found

View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68041485AD
$122.34 MSRP: $172.00
You Save: $49.66 (29%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Signal Switch; Switch Multifunction
- Replaces: 5183947AC, 68041485AA, 68041485AB, 5183947AA, 68041485AC, 5183947AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68015101AG
$95.89 MSRP: $144.00
You Save: $48.11 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 68015101AE, 68015101AD, 68015101AC, 68015101AF, 68015101AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68041491AD
$121.54 MSRP: $184.00
You Save: $62.46 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Combination Switch; Multi Purpose Switch; Multifunction Switch; Switch Multifunction
- Replaces: 68024197AB, 68041491AB, 68041491AC, 68041491AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Multifunction Switch Part Number: 68599297AA
$423.65 MSRP: $617.00
You Save: $193.35 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Combination Switch
- Replaces: 68491578AB, 68491578AA, 68399809AA, 68399809AB, 68257887AA, 68257887AB, 68526260AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 2.0L L4, 3.0L V6, 3.6L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183952AF
$55.75 MSRP: $83.35
You Save: $27.60 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 5183952AA, 5183952AC, 5183952AB, 5183952AD, 5183952AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 3.8L V6, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Multifunction Switch Part Number: 68599296AA
$295.71 MSRP: $435.00
You Save: $139.29 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Combination Switch; Clockspring
- Replaced by: 68599296AB
- Replaces: 68526259AA, 68491577AA, 68491577AB, 68399808AB, 68253862AA, 68253862AB, 68399808AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Multifunction Switch Part Number: 68599295AA
$392.74 MSRP: $572.00
You Save: $179.26 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Combination Switch
- Replaces: 68399807AA, 68491576AB, 68253861AB, 68526258AA, 68253861AA, 68399807AB, 68491576AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 2.0L L4, 3.0L V6, 3.6L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Multifunction Switch Part Number: 68599298AA
$280.98 MSRP: $415.00
You Save: $134.02 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Combination Switch; Clockspring
- Replaced by: 68599298AB
- Replaces: 68491579AA, 68399810AA, 68491579AB, 68257888AB, 68257888AA, 68526261AA, 68399810AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 56010315AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183950AF
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183950AE, 5183950AD, 5183950AC, 5183950AB, 5183950AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 3.8L V6, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183946AF
Product Specifications
- Other Name: Switch - Multifunction; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183946AA, 5183946AD, 5183946AE, 5183946AB, 5183946AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5016708AD
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls
- Replaces: 5016708AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 4 Cyl 2.4 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5016709AD
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls.
- Replaces: 5016709AB, 5016709AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 4 Cyl 2.4 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 56007255
Product Specifications
- Other Name: Switch - Turn Signal; Multi Purpose Switch; Signal Switch; Switch; Switch Assembly, Directional Signal; Switch, Turn Signal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1995 Jeep Wrangler | Renegade, Rio Grande, S, SE, Sahara | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 56002011
Product Specifications
- Other Name: Switch - Turn Signal; Hazard Flasher Switch; Multi Purpose Switch; Signal Switch; Turn Signal & Hazard Switch; Switch, Directional; Switch, Turn Signal; Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1993 Jeep Wrangler | Base, Islander, Laredo, Renegade, S, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS, 6 Cyl 4.2 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 4794357AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Wrangler Turn Signal Switch

Choose OEM Turn Signal Switch that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Turn Signal Switch follows strict manufacturing steps to lock in quality and fit. If your Jeep Wrangler matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Wrangler parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Jeep Wrangler Turn Signal Switch is the steering column lever applied to indicate to other vehicles the driver's intention to take a turn or change lanes. This Turn Signal Switch is connected to the vehicle's electrics and when swung up or down it activates a signal to illuminate the appropriate front and rear indicator lights, making intentions obvious in low-light, fog or heavy traffic conditions. The Turn Signal Switch is located inside the steering column, and frequently includes other rotary or push controls that can activate the windshield wipers, fog lights, headlights, or cruise control, making them easily accessible. A working Turn Signal Switch is essential in a Jeep Wrangler to ensure drivers share the road safely, and if one fails, it can make driving more hazardous because the indicator lamps won't turn on when the driver presses them. When replacing the Turn Signal Switch in a Jeep Wrangler, it is important to ensure it fits the car correctly and that it works properly to signal the turn signal, so durability is a key factor in ensuring the switch works constantly. This aspect is crucial in maintaining a Jeep Wrangler system that is in constant communication with other motorists.

Jeep Wrangler Turn Signal Switch Parts and Q&A

Turn Signal Switch
56010315AA
Q: How to Service and Repair a Turn Signal Switch on Jeep Wrangler?
A:
To service and repair the turn signal switch, first disconnect and isolate the battery negative cable. Remove the knee blocker from the instrument panel, then take out the three screws securing the lower Steering Column shroud to the upper shroud. For vehicles with a standard non-tilt steering column, loosen the two upper steering column mounting nuts; for those with a tilt steering column, move it to the fully lowered position. Remove both the upper and lower shrouds from the steering column. Next, remove the two screws securing the multi-function switch water shield and bracket to the top of the steering column, followed by the one screw located below the multi-function switch control stalk. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column to clear the screw boss below the control stalk. Lift the water shield and bracket with the multi-function switch off the left side of the steering column to access the two wire harness connectors, using the tilt release lever for additional clearance if necessary. Disconnect the two instrument panel wire harness connectors from the multi-function switch connector receptacles and remove the multi-function switch and water shield as a unit. For installation, carefully place the water shield onto the switch, then position the multi-function switch and water shield near their mounts on the steering column. Reconnect the two wire harness connectors, position the multi-function switch onto its mounts, and use the tilt release lever for clearance if needed. Align the lower mounting tab of the water shield bracket with the screw boss below the control stalk, then install and tighten the screw below the control stalk to 1.1 Nm (10 in. lbs.), followed by the two screws at the top of the steering column to 2.2 Nm (20 in. lbs.). Position both upper and lower shrouds onto the steering column and secure the lower shroud to the upper shroud with three screws tightened to 2 Nm (18 in. lbs.). If applicable, tighten the two nuts securing the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs to 22 Nm (200 in. lbs.). Finally, install the knee blocker onto the instrument panel and reconnect the battery negative cable.