How to Service and Repair a Timing Cover on 2001 Chrysler Sebring?

Service and repair of the timing cover involve first removing the upper timing belt cover screws and lifting off the cover. Before performing any work, remove the negative battery cable and lift the car on a hoist. After that, take off the right front wheel, then remove the shield near the right front end, the two accessory drive belts, the crankshaft damper and the AC/Generator belt tensioner. After lowering the vehicle, remove the generators connectors and uninstall the entire part. Take the vehicle's nose up again so you can remove the bolts or screws holding the lower timing cover and after that, take off the cover. Information: After that, remove the timing belt covers at both front ends, the timing belt and the timing belt idler pulley. Unhook both camshaft sprockets and then remove the center screws after you have Special Tool 6847 to help. Afterwards, undo the fasteners that hold the rear timing belt cover and take the cover off the engine. The first step for installation should be the upper timing belt cover, fastening the bolts to 4.5 Nm (40 in. lbs). Fit the lower timing belt cover and tighten all its fasteners to the recommended value. Take the car to the ground and join the generator to the bracket, linking the generator connectors. Raise the vehicle for a second time to put on the belt tensioner, crankshaft damper and accessory belts. After installing the belt splash shield and right front wheel, only then lower the vehicle and reconnect the negative battery cable. After that, install the cover and fasteners for the rear timing belt, tightening them according to instructions, next fit the camshaft sprockets and keep them in place with SP Tool 6847 when installing the center bolts, where tightening to 101 Nm (75 ft. lbs). Set up the idler pulley, the timing belt and both covers for the upper and lower front timing belts.

OEM 2001 Chrysler Sebring Timing Cover

Engine Timing Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Timing Covers found

View related parts
2001 Chrysler Sebring Front Cover, Upper Part Number: MD378731
$35.82 MSRP: $65.85
You Save: $30.03 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Upper; Upper Cover; Cover Timing Belt; Timing Cover
- Position: Upper
- Item Weight: 1.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD378731
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2001 Chrysler Sebring Front Cover, Driver Side Part Number: MD376390
$44.84 MSRP: $56.85
You Save: $12.01 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Front; Rear Cover; Cover Timing Belt
- Position: Front Driver Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.0 x 6.4 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD376390
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Timing Cover Part Number: 4792604AA
$222.22 MSRP: $281.71
You Save: $59.49 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover; Front Cover; Cover Timing Belt
- Item Weight: 5.20 Pounds
- Item Dimensions: 14.0 x 13.9 x 6.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792604AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Timing Cover, Lower Outer Part Number: 5093131AA
Product Specifications
- Other Name: Cover Package - Timing; Engine Timing Cover, Lower Outer; Lower Cover; Outer Timing Cover; Cover Package Timing
- Position: Lower Outer
- Item Weight: 0.90 Pounds
- Item Dimensions: 12.6 x 9.8 x 1.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5093131AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- GTC, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L GAS
View related parts
2001 Chrysler Sebring Front Cover, Lower Part Number: MD363100
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Lower; Lower Cover; Cover Timing Belt
- Position: Lower
- Item Weight: 1.10 Pounds
- Item Dimensions: 13.9 x 11.6 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD363100
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2001 Chrysler Sebring Front Cover, Lower Part Number: MD325374
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Front Lower; Lower Cover; Cover Timing Belt; Timing Cover
- Position: Front Lower
- Item Weight: 0.90 Pounds
- Item Dimensions: 13.3 x 9.5 x 2.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD325374
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Front Cover, Passenger Side Part Number: MD376392
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Front; Cover Timing Belt
- Position: Front Passenger Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.7 x 9.2 x 2.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD376392
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Inner Cover Part Number: MD330008
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Inner; Lower Cover; Cover Timing Belt; Timing Cover
- Position: Inner
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD330008
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2001 Chrysler Sebring Front Cover, Inner Part Number: MR984958
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Inner, Rear; Inner Cover; Cover Timing Belt
- Position: Inner
- Item Weight: 0.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR984958
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Timing Cover, Inner Part Number: 4694318AD
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Inner; Front Cover; Inner Cover; Inner Timing Cover; Cover Timing Belt
- Position: Inner
- Replaces: 4694318, 4694318AC, 4694318AB
- Item Weight: 1.60 Pounds
- Item Dimensions: 21.1 x 12.8 x 2.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4694318AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- GTC, LX, LXi, Limited | 2.4L L4, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L GAS
View related parts
2001 Chrysler Sebring Timing Cover, Upper Outer Part Number: 5093132AA
Product Specifications
- Other Name: Cover Package - Timing; Engine Timing Cover, Upper Outer; Front Cover; Upper Cover; Outer Timing Cover; Cover Package Timing
- Position: Upper Outer
- Item Weight: 0.80 Pounds
- Item Dimensions: 13.4 x 8.9 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5093132AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- GTC, JX, JXi, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L GAS

2001 Chrysler Sebring Timing Cover Parts and Q&A

Q: How to Service and Repair a Timing Cover on 2001 Chrysler Sebring?
A: Service and repair of the timing cover involve first removing the upper timing belt cover screws and lifting off the cover. Before performing any work, remove the negative battery cable and lift the car on a hoist. After that, take off the right front wheel, then remove the shield near the right front end, the two accessory drive belts, the crankshaft damper and the AC/Generator belt tensioner. After lowering the vehicle, remove the generators connectors and uninstall the entire part. Take the vehicle's nose up again so you can remove the bolts or screws holding the lower timing cover and after that, take off the cover. Information: After that, remove the timing belt covers at both front ends, the timing belt and the timing belt idler pulley. Unhook both camshaft sprockets and then remove the center screws after you have Special Tool 6847 to help. Afterwards, undo the fasteners that hold the rear timing belt cover and take the cover off the engine. The first step for installation should be the upper timing belt cover, fastening the bolts to 4.5 Nm (40 in. lbs). Fit the lower timing belt cover and tighten all its fasteners to the recommended value. Take the car to the ground and join the generator to the bracket, linking the generator connectors. Raise the vehicle for a second time to put on the belt tensioner, crankshaft damper and accessory belts. After installing the belt splash shield and right front wheel, only then lower the vehicle and reconnect the negative battery cable. After that, install the cover and fasteners for the rear timing belt, tightening them according to instructions, next fit the camshaft sprockets and keep them in place with SP Tool 6847 when installing the center bolts, where tightening to 101 Nm (75 ft. lbs). Set up the idler pulley, the timing belt and both covers for the upper and lower front timing belts.