How to Service and Repair a Brake Caliper on Rear Disc Brakes on 2004 Chrysler Crossfire?

Before servicing or repairing the rear disc brake caliper, raise and support the vehicle and then remove the rear wheel and tire. Remove a little bit of brake fluid from the reservoir with a clean suction gun. Untighten and remove the caliper bolts and lift the caliper from the knuckle to avoid having brake fluid come into contact with anything painted. Turn the caliper as you hold the brake hose in place with a wrench. Blow out the retaining pin with an appropriate punch and then get rid of the anti-rattle clip, as well as the brake pads, from the caliper. Remove the caliper from the car and examine its parts for signs of wear. During installation, slide the rear brake pads into position, wrench and rotate the caliper to fit the brake hose and make sure there is no bend by tightening the bolts to 55 Nm (40 ft. lbs.). Perform a complete brake system fill and bleed and then attach the wheel and tire assembly back. You should not begin to move the vehicle until the brakes have become firm by pumping the brake pedal.

OEM 2004 Chrysler Crossfire Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Calipers found

View related parts
2004 Chrysler Crossfire Caliper, Rear Driver Side Part Number: 5126303AA
$67.99 MSRP: $86.18
You Save: $18.19 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Item Weight: 3.20 Pounds
- Item Dimensions: 7.4 x 6.5 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5126303AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Chrysler Crossfire Submodels:
- Base, Limited | 6 Cyl 3.2 L GAS
View related parts
2004 Chrysler Crossfire Caliper, Front Driver Side Part Number: 5139587AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Item Weight: 9.20 Pounds
- Item Dimensions: 8.3 x 7.0 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5139587AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Chrysler Crossfire Submodels:
- Base, Limited | 6 Cyl 3.2 L GAS
View related parts
2004 Chrysler Crossfire Caliper, Front Passenger Side Part Number: 5139586AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Item Weight: 8.90 Pounds
- Item Dimensions: 8.4 x 6.7 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5139586AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Chrysler Crossfire Submodels:
- Base, Limited | 6 Cyl 3.2 L GAS
View related parts
2004 Chrysler Crossfire Caliper, Rear Passenger Side Part Number: 5126302AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Disc Brake; Brake Caliper
- Position: Rear Passenger Side
- Item Weight: 6.60 Pounds
- Item Dimensions: 7.7 x 6.8 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5126302AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Chrysler Crossfire Submodels:
- Base, Limited | 6 Cyl 3.2 L GAS

2004 Chrysler Crossfire Brake Caliper Parts and Q&A

Q: How to Service and Repair a Brake Caliper on Rear Disc Brakes on 2004 Chrysler Crossfire?
A: Before servicing or repairing the rear disc brake caliper, raise and support the vehicle and then remove the rear wheel and tire. Remove a little bit of brake fluid from the reservoir with a clean suction gun. Untighten and remove the caliper bolts and lift the caliper from the knuckle to avoid having brake fluid come into contact with anything painted. Turn the caliper as you hold the brake hose in place with a wrench. Blow out the retaining pin with an appropriate punch and then get rid of the anti-rattle clip, as well as the brake pads, from the caliper. Remove the caliper from the car and examine its parts for signs of wear. During installation, slide the rear brake pads into position, wrench and rotate the caliper to fit the brake hose and make sure there is no bend by tightening the bolts to 55 Nm (40 ft. lbs.). Perform a complete brake system fill and bleed and then attach the wheel and tire assembly back. You should not begin to move the vehicle until the brakes have become firm by pumping the brake pedal.