How to Service and Repair Engine Mounts for 2WD and 4WD Configurations on 2004 Dodge Durango?

Before working on the front engine mount, first disconnect the battery's negative cable and take out the viscous fan so that you don't damage anything when lifting the engine. Lift the 2WD, take out the engine oil filter and oil trough, place a jack and wood block at the back of the oil pan to support the engine. Support the front axle with a jack, take out the bolts attaching the side engine mounts and the three bolts that keep the front axle connected to the left engine bracket, then lower the axle. Take out the through bolts and lift the engine so you can remove the left and right mounts with their eight bolts. When working on a 4WD, carry out the original steps and also remove the skid plate and crossmember in front. After you are done with the engine mounts, flush the front axle, fasten the engine bolts, remove the four joining the mounts to the front axle and then remove the three holding the front axle to the side engine bracket. For both kinds of installations, use Mopar Lock and Seal Adhesive on the engine block and also on the front axle side of the left engine bracket bolts. With the 2WD model, place the mounts onto the engine block and screw in eight bolts to 54 Nm (40 ft. lbs.). Next, add the two through bolts into each mount, lower the engine as the bolts are captured by the frame brackets and tighten up the through bolts to 94 Nm (70 ft. lbs.). Replace the oil drain trough, the engine oil filter, drive the vehicle up, join the viscous fan and reattach the negative battery cable. On the front axle, install the two engine mounts, torque the nuts to 94 Nm (70 ft. lbs.) and elevate the front axle. After that, put in the two front through bolts. Attach the two bolts in the top of each plate to the mounting points on the engine and wheel. Lower the engine until your left bracket fits the front axle again. Tighten the four through bolts and the three bolts to 101 Nm (75 ft. lbs.), then put the oil drain trough, engine oil filter, front crossmember and skid plate back into place, lower the car, fix the viscous fan and attach the negative battery wire.

OEM 2004 Dodge Durango Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Engine Mounts found

View related parts
2004 Dodge Durango Front Mount, Rear Part Number: 52021614AA
$51.60 MSRP: $94.95
You Save: $43.35 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Rear; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Insulator Engine Mount
- Position: Rear
- Replaces: 52855458AA
- Item Weight: 6.30 Pounds
- Item Dimensions: 8.0 x 4.9 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021614AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Front Part Number: 52021709AB
$16.67 MSRP: $23.95
You Save: $7.28 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket; Engine Mount, Front; Motor Mount; Valve Grind Gasket Kit; Lower Gasket Kit; Front Insulator; Bracket Engine Mount
- Position: Front
- Item Weight: 5.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021709AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Passenger Side Part Number: 52021636AB
$23.47 MSRP: $29.75
You Save: $6.28 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Right, Right; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Replaces: 52021636AA
- Item Weight: 2.40 Pounds
- Item Dimensions: 7.3 x 5.4 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021636AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 5.7L V8, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Passenger Side Part Number: 52021638AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Right, Right; Motor Mount; Front Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021638AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Driver Side Part Number: 52021633AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855455AB
- Item Weight: 9.90 Pounds
- Item Dimensions: 5.3 x 6.7 x 7.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021633AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Driver Side Part Number: 52855171AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left; Motor Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Driver Side
- Item Weight: 5.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855171AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Engine Bracket, Passenger Side Part Number: 52005013AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left, Right; Motor Mount; Bracket Engine Mount
- Position: Passenger Side
- Item Weight: 4.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52005013AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Front Driver Side Part Number: 52021639AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Left, Left; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Front Driver Side
- Replaces: 52021639AA
- Item Weight: 4.30 Pounds
- Item Dimensions: 6.7 x 5.5 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021639AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SE, SLT, ST, SXT | 4.7L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Front Driver Side Part Number: 52122775AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front Left, Left; Motor Mount; Front Bracket; Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Front Driver Side
- Replaces: 52021637AB, 52021637AA
- Item Weight: 2.30 Pounds
- Item Dimensions: 24.7 x 15.8 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52122775AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 5.7L V8, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Passenger Side Part Number: 52855236AD
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Engine Mount Bracket; Motor Mount
- Position: Passenger Side
- Replaces: 52855236AC, 52855236AE, 52855236AB
- Item Weight: 5.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52855236AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Mount Bracket, Front Part Number: 52021629AA
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Front, Right; Motor Mount; Engine Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Front
- Item Weight: 3.80 Pounds
- Item Dimensions: 6.0 x 5.3 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021629AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, Limited Hybrid, SLT, ST, SXT | 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Driver Side Part Number: 52021627AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Left; Engine Mount Bracket; Motor Mount; Insulator Engine Mount
- Position: Front Driver Side
- Replaces: 52855453AB
- Item Weight: 2.60 Pounds
- Item Dimensions: 7.9 x 6.2 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021627AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- SLT, ST, SXT | 6 Cyl 3.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Passenger Side Part Number: 52021626AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Right; Engine Mount Bracket; Motor Mount; Insulator Engine Mount
- Position: Front Passenger Side
- Replaces: 52855452AB
- Item Weight: 6.90 Pounds
- Item Dimensions: 6.7 x 6.1 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021626AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- SLT, ST, SXT | 6 Cyl 3.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Passenger Side Part Number: 52021632AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Replaces: 52855454AB
- Item Weight: 7.30 Pounds
- Item Dimensions: 6.7 x 6.5 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021632AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Passenger Side Part Number: 52021610AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Replaces: 52855456AB
- Item Weight: 7.20 Pounds
- Item Dimensions: 7.1 x 6.1 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021610AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Front Mount, Driver Side Part Number: 52021611AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855457AB
- Item Weight: 9.10 Pounds
- Item Dimensions: 8.0 x 7.4 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021611AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Durango Front Mount Part Number: 52021615AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Front
- Replaces: 52855459AA
- Item Weight: 7.80 Pounds
- Item Dimensions: 7.3 x 6.7 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021615AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Durango Submodels:
- Adventurer, Limited, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

2004 Dodge Durango Engine Mount Parts and Q&A

Q: How to Service and Repair Engine Mounts for 2WD and 4WD Configurations on 2004 Dodge Durango?
A: Before working on the front engine mount, first disconnect the battery's negative cable and take out the viscous fan so that you don't damage anything when lifting the engine. Lift the 2WD, take out the engine oil filter and oil trough, place a jack and wood block at the back of the oil pan to support the engine. Support the front axle with a jack, take out the bolts attaching the side engine mounts and the three bolts that keep the front axle connected to the left engine bracket, then lower the axle. Take out the through bolts and lift the engine so you can remove the left and right mounts with their eight bolts. When working on a 4WD, carry out the original steps and also remove the skid plate and crossmember in front. After you are done with the engine mounts, flush the front axle, fasten the engine bolts, remove the four joining the mounts to the front axle and then remove the three holding the front axle to the side engine bracket. For both kinds of installations, use Mopar Lock and Seal Adhesive on the engine block and also on the front axle side of the left engine bracket bolts. With the 2WD model, place the mounts onto the engine block and screw in eight bolts to 54 Nm (40 ft. lbs.). Next, add the two through bolts into each mount, lower the engine as the bolts are captured by the frame brackets and tighten up the through bolts to 94 Nm (70 ft. lbs.). Replace the oil drain trough, the engine oil filter, drive the vehicle up, join the viscous fan and reattach the negative battery cable. On the front axle, install the two engine mounts, torque the nuts to 94 Nm (70 ft. lbs.) and elevate the front axle. After that, put in the two front through bolts. Attach the two bolts in the top of each plate to the mounting points on the engine and wheel. Lower the engine until your left bracket fits the front axle again. Tighten the four through bolts and the three bolts to 101 Nm (75 ft. lbs.), then put the oil drain trough, engine oil filter, front crossmember and skid plate back into place, lower the car, fix the viscous fan and attach the negative battery wire.