How to Remove and Install a MAP Sensor on 2004 Jeep Wrangler?

You will find the Manifold Absolute Pressure (MAP) sensor at the back of the intake manifold and it is sealed with an O-ring. First, take out the MAP sensor connector, then give the area of the sensor a good cleaning. Then, remove the screw holding the sensor in place, using a TORX tool and take the sensor out of the car's intake manifold. Check if the sensor O-ring is broken in any area. When installing, clean the opening in the intake manifold for the MAP sensor and inspect the seal for any defects. Place the sensor inside the manifold and put the screws in place, turning them to 3 Nm (25 in. lbs.) torque before you plug in the connector.

OEM 2004 Jeep Wrangler MAP Sensor

Manifold Air Pressure Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 MAP Sensors found

View related parts
2004 Jeep Wrangler M.A.P. Sensor Part Number: 68002763AA
$112.00 MSRP: $167.00
You Save: $55.00 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Map; Manifold Absolute Pressure Sensor; Manifold Sensor; Pressure Sensor; MAP Sensor
- Item Weight: 0.50 Pounds
- Item Dimensions: 1.0 x 2.4 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68002763AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Jeep Wrangler Submodels:
- SE | 4 Cyl 2.4 L GAS
View related parts
2004 Jeep Wrangler M.A.P. Sensor Part Number: 56029405
Product Specifications
- Other Name: Sensor - Map; Manifold Absolute Pressure Sensor; Manifold Sensor; MAP Sensor; Sensor Map See Note; Sensor Map; Pressure Sensor
- Item Weight: 0.50 Pounds
- Item Dimensions: 2.8 x 2.6 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56029405
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Jeep Wrangler Submodels:
- Rubicon, SE, Sahara, Sport, Unlimited, X | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2004 Jeep Wrangler M.A.P. Sensor Part Number: 56044545AB
Product Specifications
- Other Name: Sensor - Map; Manifold Absolute Pressure Sensor; Manifold Sensor; Pressure Sensor; MAP Sensor
- Replaces: 56044545AA
- Item Weight: 0.50 Pounds
- Item Dimensions: 3.7 x 2.6 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56044545AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Jeep Wrangler Submodels:
- Rubicon, Sahara, Sport, Unlimited, X | 4.0L V6, 6 Cyl 4.0 L GAS

2004 Jeep Wrangler MAP Sensor Parts and Q&A

Q: How to Remove and Install a MAP Sensor on 2004 Jeep Wrangler?
A: You will find the Manifold Absolute Pressure (MAP) sensor at the back of the intake manifold and it is sealed with an O-ring. First, take out the MAP sensor connector, then give the area of the sensor a good cleaning. Then, remove the screw holding the sensor in place, using a TORX tool and take the sensor out of the car's intake manifold. Check if the sensor O-ring is broken in any area. When installing, clean the opening in the intake manifold for the MAP sensor and inspect the seal for any defects. Place the sensor inside the manifold and put the screws in place, turning them to 3 Nm (25 in. lbs.) torque before you plug in the connector.