How to Service and Repair an Exhaust Manifold on 2005 Chrysler Sebring?

Before servicing or repairing the exhaust manifold, take the battery cable off and lift the car on a hoist. Take off the entire exhaust system and then remove the engine mount and transaxle bracket at the back. If you have a connector tube, squeeze it and pull it off the check valve. After that, detach the exhaust manifold heat shield and disconnect the wire from the oxygen sensor. Disconnect the nuts or bolts that hold the exhaust manifold and then remove the manifold, throwing away the gasket. Clean each surface of the manifold and cylinder head, inspect the gasket surface on the manifold for flatness and check for any cracks or distortion, changing the manifold when necessary. To install, place a new exhaust manifold gasket on the head and do not use sealer, place the exhaust manifold and tighten screws in the right order for non-PZEV engines to 17 foot lbs. or for PZEV engines to the same torque. Attach the exhaust manifold heat shield once you have it and if there is a check valve, set its bolts to 12 Nm (105 inch lbs.). Attach the connector tube to the check valve, link the oxygen sensor wiring once more and place the rear engine mount and transaxle bracket back. Then, attach the exhaust system by fastening it with a torque wrench set to 28 Nm (250 inch lbs.), bring the vehicle down on the stands and plug back in the negative battery cable.

OEM 2005 Chrysler Sebring Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Exhaust Manifolds found

View related parts
2005 Chrysler Sebring Exhaust Manifold Part Number: MR597478
Product Specifications
- Other Name: Manifold - Exhaust; Catalytic Converter with Integrated Exhaust Manifold; Manifold Exhaust
- Item Weight: 14.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR597478
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2005 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2005 Chrysler Sebring Exhaust Manifold, Passenger Side Part Number: MR481816
Product Specifications
- Other Name: Manifold - Exhaust Right; Exhaust Manifold, Right; Manifold Exhaust Right
- Position: Passenger Side
- Item Weight: 9.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR481816
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2005 Chrysler Sebring Exhaust Manifold, Driver Side Part Number: MR481815
Product Specifications
- Other Name: Manifold - Exhaust Left; Exhaust Manifold, Left; Manifold Exhaust Left
- Position: Driver Side
- Item Weight: 9.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR481815
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2005 Chrysler Sebring Exhaust Manifold Part Number: 4792538AA
Product Specifications
- Other Name: Manifold - Exhaust; Manifold; Manifold Exhaust Manifold For Edv Engine Is Part Of Turbo Assembly; Manifold Exhaust
- Item Weight: 15.60 Pounds
- Item Dimensions: 14.3 x 14.3 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792538AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2005 Chrysler Sebring Exhaust Manifold, Passenger Side Part Number: 4792387AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Item Weight: 8.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792387AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2005 Chrysler Sebring Exhaust Manifold, Passenger Side Part Number: 4792386AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Item Weight: 8.30 Pounds
- Item Dimensions: 14.3 x 8.1 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4792386AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS

2005 Chrysler Sebring Exhaust Manifold Parts and Q&A

Q: How to Service and Repair an Exhaust Manifold on 2005 Chrysler Sebring?
A: Before servicing or repairing the exhaust manifold, take the battery cable off and lift the car on a hoist. Take off the entire exhaust system and then remove the engine mount and transaxle bracket at the back. If you have a connector tube, squeeze it and pull it off the check valve. After that, detach the exhaust manifold heat shield and disconnect the wire from the oxygen sensor. Disconnect the nuts or bolts that hold the exhaust manifold and then remove the manifold, throwing away the gasket. Clean each surface of the manifold and cylinder head, inspect the gasket surface on the manifold for flatness and check for any cracks or distortion, changing the manifold when necessary. To install, place a new exhaust manifold gasket on the head and do not use sealer, place the exhaust manifold and tighten screws in the right order for non-PZEV engines to 17 foot lbs. or for PZEV engines to the same torque. Attach the exhaust manifold heat shield once you have it and if there is a check valve, set its bolts to 12 Nm (105 inch lbs.). Attach the connector tube to the check valve, link the oxygen sensor wiring once more and place the rear engine mount and transaxle bracket back. Then, attach the exhaust system by fastening it with a torque wrench set to 28 Nm (250 inch lbs.), bring the vehicle down on the stands and plug back in the negative battery cable.