How to Service a Blend Door Actuator on 2005 Dodge Stratus?

Before servicing the front blend door actuator, first disconnect and isolate the negative battery cable to disable the air bag system, then wait for two minutes so the air bag system capacitor empties. Take out the right lower silencer panel and cover from the dash trim first. Following this, open the three screws holding the blend door actuator to the underside of the HVAC housing. Remember the location of the shaft and its linkage for correct reassembly. Get the actuator out of the HVAC section and then take off the HVAC wire harness connector from the car. In order to install, attach the blend door actuator to the HVAC housing, making sure the splines on its output shaft are with those on the blend door cam and fasten it using the three screws torqued to 2 N.m (17 in. lbs.). Connect the HVAC wire harness, mount the instruments panel cover and silencer panel and reconnect the negative battery cable.

OEM 2005 Dodge Stratus Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Blend Door Actuators found

View related parts
2005 Dodge Stratus Door Actuator Part Number: 4885206AB
$137.09 MSRP: $202.00
You Save: $64.91 (33%)
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Servo; A/C and Heater Actuator with Bracket, Lever, and Recirculation Door.
- Item Weight: 0.70 Pounds
- Item Dimensions: 1.9 x 3.6 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885206AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2005 Dodge Stratus Actuator Part Number: 4885457AC
Product Specifications
- Other Name: Actuator - Mode Control; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator Mode Control
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.4 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885457AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2005 Dodge Stratus Actuator Part Number: 4885207AB
Product Specifications
- Other Name: Actuator - Blend Door; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Actuator Blend Door
- Item Weight: 0.70 Pounds
- Item Dimensions: 5.1 x 3.8 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885207AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS

2005 Dodge Stratus Blend Door Actuator Parts and Q&A

Q: How to Service a Blend Door Actuator on 2005 Dodge Stratus?
A: Before servicing the front blend door actuator, first disconnect and isolate the negative battery cable to disable the air bag system, then wait for two minutes so the air bag system capacitor empties. Take out the right lower silencer panel and cover from the dash trim first. Following this, open the three screws holding the blend door actuator to the underside of the HVAC housing. Remember the location of the shaft and its linkage for correct reassembly. Get the actuator out of the HVAC section and then take off the HVAC wire harness connector from the car. In order to install, attach the blend door actuator to the HVAC housing, making sure the splines on its output shaft are with those on the blend door cam and fasten it using the three screws torqued to 2 N.m (17 in. lbs.). Connect the HVAC wire harness, mount the instruments panel cover and silencer panel and reconnect the negative battery cable.