How to Properly Install a Brake Caliper on Chrysler Pacifica?

Always look at the noise reduction gasket on the brake pads; if it appears cracked or missing, you should replace both brake pads before installing the caliper. Place the disc brake caliper across the brake pads in the brake caliper adapter, being careful not to harm the boots at the caliper guide pins. Guide pins and holes must be aligned to set the calipers back to normal. Tighten the upper bolt near the bleeder screw to 43 Nm (32 ft. lbs.), then tighten its counterpart bolt to the same figure. Once done, insert the banjo bolt (7) through the brake hole, adding a washer (5) to each side of the fitting and then tightening the bolt to 47 Nm (35 ft. lbs.) with the spanner. Then, attach the tire and wheel assembly (1) and turn the wheel mounting nuts (3) up to 135 Nm (100 ft. lbs.). Disconnect the car, lower it and take out the brake pedal holding device, then complete by linking the negative (-) cable to its post on the battery. When you are done, release the pressure from the base hydraulic brakes, do a road test and stop several times to remove dirt from the brakes and firmly fix the brake pads.

How to Remove and Replace a Rear Brake Caliper on Chrysler Pacifica?

Start by pushing the caliper piston past its stop to give room for the caliper to be removed, using a C-clamp or pressure from your hand and make sure a wood block is over the piston to prevent damage. Align the retainer clip near the cavity in the piston and push it securely so it seats next to the backing plate which should now touch the caliper piston. When you install the outboard brake pads, be sure the spring clip is placed downward. Afterward, guide the pins on the outboard brake pad to the holes in the caliper ramps and, while the pad is against the fingers, slide the pad into the caliper. Set the abutment shims on the two caliper slide abutments, trying to not harm the guide pin bushings and sleeves during installation. Withdraw the caliper guide pins to release the brake caliper from the mounting bosses, then place the caliper on the adapter upside down, making sure the outside brake pad's upper edge touches the correct abutment-now turn the lower part into place on the adapter. Make sure not to cross-thread the caliper guide pin bolts when you are installing them; tighten them to 23 Nm (17 ft. lbs.). Install the tire rim and wheel, tightening the mounting nuts to 135 Nm (100 ft. lbs.). After that, lower the vehicle and take out the brake pedal holding tool. Connect the negative terminal of the battery and then bleed the brake hydraulic system if it needs bleeding. In the end, carry out a road test to check that the brakes work as they should and the brake shoes are correctly seated.

OEM Chrysler Pacifica Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Brake Calipers found

View related parts
Chrysler Pacifica Caliper Part Number: 68509084AA
$134.43 MSRP: $199.00
You Save: $64.57 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Front Driver Side Part Number: 68509085AA
$135.56 MSRP: $202.00
You Save: $66.44 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper Part Number: 68546278AA
$165.02 MSRP: $247.00
You Save: $81.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Front Driver Side Part Number: 68546277AA
$165.02 MSRP: $247.00
You Save: $81.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Front Driver Side Part Number: 68144161AA
$178.30 MSRP: $262.00
You Save: $83.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Replaces: 68144161AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Front Passenger Side Part Number: 68144160AA
$178.30 MSRP: $262.00
You Save: $83.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Replaces: 68144160AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper - Disc Brake Part Number: 68675593AA
$64.46 MSRP: $95.25
You Save: $30.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER-DISC BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica CALIPER-DISC BRAKE Part Number: 68675592AA
$64.46 MSRP: $95.25
You Save: $30.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica CALIPER-DISC BRAKE Part Number: 68675552AA
$72.65 MSRP: $108.00
You Save: $35.35 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Rear Driver Side Part Number: 68318173AB
$292.73 MSRP: $430.00
You Save: $137.27 (32%)
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Replaces: 68318173AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Rear Passenger Side Part Number: 68318172AB
$285.51 MSRP: $430.00
You Save: $144.49 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Replaces: 68318172AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Caliper, Front Passenger Side Part Number: 68032692AA
$72.79 MSRP: $105.00
You Save: $32.21 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Pacifica | LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Caliper, Front Driver Side Part Number: 5103119AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Caliper, Front Passenger Side Part Number: 5103118AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Caliper, Rear Driver Side Part Number: 5114441AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Caliper, Front Driver Side Part Number: 68032693AA
Product Specifications
- Other Name: Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Pacifica | LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Caliper, Rear Passenger Side Part Number: 5114440AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Disc Brake; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Steering Column Part Number: 5066106AC
Product Specifications
- Other Name: Column - Steering; Column Assembly; Caliper
- Replaces: 5066106AB, 5103440AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2006 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS

Chrysler Pacifica Brake Caliper

Choose OEM Brake Caliper that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Caliper follows strict manufacturing steps to lock in quality and fit. If your Chrysler Pacifica matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Pacifica parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Pacifica Brake Caliper is one of the brake system parts appreciated for its reliability and performance, thus can be used on different types of Pacifica. This important component translates hydraulic pressure geared from the master cylinder to mechanical pressure or force that applies brake pads on the rotors for safe and effective braking system. Another detail of the car's upholstery is that brake calipers are of two kinds - fixed and floating, each having its benefits for Chrysler's Pacifica. There are fixed as well as floating calipers; the fixed ones remain constant with multiple pistons which deliver pressure and the floating ones adjust the pressure according to wear, and do improve the overall braking of the car. It is fit to a range of models and it guarantees that the driver will have the premier experience when using this product regardless of the settings of his car model. Adverse factors like leaks and uneven wear are probable if the brake caliper is not maintained properly and that is why you should have your brake caliper serviced regularly. Additionally, the Chrysler Pacifica Brake Caliper is offered in a number of types, including more cost-effective cast one and lightweight aluminum one responding to the specific requirement of driving. This multitalented function empowered by the awarded Pacifica minivan as "The premier Minivan" and "The premier Family Car" proves the importance of a brake caliper in the field of performance and safety. Concerning the Chrysler Pacifica Brake Caliper, the company has highly-engineered the product and incorporated the premier quality, making every trip safe and smooth in the market.

Chrysler Pacifica Brake Caliper Parts and Q&A

Caliper, Front Passenger Side
5103118AA
Q: How to Properly Install a Brake Caliper on Chrysler Pacifica?
A:
Always look at the noise reduction gasket on the Brake Pads; if it appears cracked or missing, you should replace both brake pads before installing the caliper. Place the disc brake caliper across the brake pads in the brake caliper adapter, being careful not to harm the boots at the caliper guide pins. Guide pins and holes must be aligned to set the calipers back to normal. Tighten the upper bolt near the bleeder screw to 43 Nm (32 ft. lbs.), then tighten its counterpart bolt to the same figure. Once done, insert the banjo bolt (7) through the brake hole, adding a washer (5) to each side of the fitting and then tightening the bolt to 47 Nm (35 ft. lbs.) with the spanner. Then, attach the tire and wheel assembly (1) and turn the wheel mounting nuts (3) up to 135 Nm (100 ft. lbs.). Disconnect the car, lower it and take out the brake pedal holding device, then complete by linking the negative (-) cable to its post on the battery. When you are done, release the pressure from the base hydraulic brakes, do a road test and stop several times to remove dirt from the brakes and firmly fix the brake pads.
Caliper, Rear Passenger Side
5114440AA
Q: How to Remove and Replace a Rear Brake Caliper on Chrysler Pacifica?
A:
Start by pushing the caliper piston past its stop to give room for the caliper to be removed, using a C-clamp or pressure from your hand and make sure a wood block is over the piston to prevent damage. Align the retainer clip near the cavity in the piston and push it securely so it seats next to the backing plate which should now touch the caliper piston. When you install the outboard Brake Pads, be sure the spring clip is placed downward. Afterward, guide the pins on the outboard brake pad to the holes in the caliper ramps and, while the pad is against the fingers, slide the pad into the caliper. Set the abutment shims on the two caliper slide abutments, trying to not harm the guide pin bushings and sleeves during installation. Withdraw the caliper guide pins to release the brake caliper from the mounting bosses, then place the caliper on the adapter upside down, making sure the outside brake pad's upper edge touches the correct abutment-now turn the lower part into place on the adapter. Make sure not to cross-thread the caliper guide pin bolts when you are installing them; tighten them to 23 Nm (17 ft. lbs.). Install the tire rim and wheel, tightening the mounting nuts to 135 Nm (100 ft. lbs.). After that, lower the vehicle and take out the brake pedal holding tool. Connect the negative terminal of the battery and then bleed the brake hydraulic system if it needs bleeding. In the end, carry out a road test to check that the brakes work as they should and the brake shoes are correctly seated.