How to Service and Repair Brake Pads on the Front Wheels on Chrysler Pacifica?

First, get rid of the fluid reservoir cap from the master cylinder and lift up the vehicle for servicing the front brake pads. First, remove the tire and wheel assembly, then set a C-clamp over the brake caliper, with the screw-drive head hitting the outside shoe and the hook placed at the rear of the caliper. Slightly tighten the valve stem by turning the valve knob cautiously to let the pistons go back and unbind the outermost brake shoe from the caliper fingers. After you've removed the outboard shoe, pull the caliper further inboard so the rotor creates some space between itself and the inboard brake shoe. Separate the brake shoe from the caliper pistons without causing any harm to either. Free the brake caliper guide pin bolts and get the caliper off of the brake adapter, then lower it by its support or hang it out of the way so as not to overstretch the brake cable. Take the brake shoes out of the disc brake caliper adapter and afterward, install the reservoir cap on the master cylinder. Placement should be done with the new brake shoes over the anti-rattle clips and you should verify proper clip installation. If required, remove the paper covering from the noise suppression gasket sticking to the outer and inner brake shoes' rear surfaces. Slide the piston back into the caliper all the way to its mounting location, watching out not to harm the caliper guide pins' boots during the process. Place the disc brake caliper over the brake shoes while they're mounted on the adapter and then tighten the upper caliper guide pin bolt to 43 Nm. After that, tighten the lower bolt to 43 Nm as well. Put the tire and wheel back in place and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), before lowering the vehicle. Press the brake pedal firmly two to three times to put the shoes on the rotor and caliper, check the brake fluid reservoir and complete a short drive to make sure the brakes are working properly.

How to Properly Install and Service a Brake Pads on Chrysler Pacifica?

Before mounting the caliper onto the knuckle, pull the caliper piston back into the caliper bore to give enough space for the pads against the rotor. Hold the inboard pad retainer clip against the piston cavity and press fiercely until it sits in the groove, so the inboard brake pad backing plate is flat on the piston. Make sure the outboard brake pads are in place and the spring clip is installed downward, after the caliper is set in. Then, fit the outboard brake pad locating pins against the end of each ramp on the caliper fingers and slide the pad onto the caliper so the fingers rest on the pads and the pins go perfectly into the holes. The shims on both the upper and lower slide abutments of the caliper adapter must be in place before joining the caliper assembly and care should be taken not to damage any parts nearby. After the caliper guide pins are retracted, clear the bosses on the caliper adapter and mount the caliper lower end first, with the outboard pad's upper edge fitting the caliper slide abutment. Fit the guide pin bolts in their caliper holes and tighten them to 23 Nm (17 ft. lbs.), then fit the tire and wheel onto the studs and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.). Reduce the car and pump the brake pedal as needed until your brake pedal feels firm, check the fluid in the reservoir and top it off when needed and then go for a drive, braking moderately many times to erase foreign materials from the brakes and make the pads fit to the disc better.

OEM Chrysler Pacifica Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Pads found

View related parts
Chrysler Pacifica Brake Pads, Rear Part Number: 68029298AA
$18.61 MSRP: $23.59
You Save: $4.98 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Rear Pads; Pad Kit Rear Disc Brake; Disc Brake Pad Set
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Pacifica | LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Brake Pads, Rear Part Number: 68318171AB
$74.55 MSRP: $147.00
You Save: $72.45 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: 68318171AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, Limited, LX, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Front Part Number: 68317914AC
$160.06 MSRP: $245.00
You Save: $84.94 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: 68317914AB, 68317914AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, Limited, LX, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Front Part Number: 68526734AA
$85.13 MSRP: $128.00
You Save: $42.87 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Disc Brake Pad Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2025 Chrysler Pacifica | Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Rear Part Number: 68509087AA
$248.63 MSRP: $375.00
You Save: $126.37 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Front Part Number: 68509081AB
$253.05 MSRP: $382.00
You Save: $128.95 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 68509081AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Rear Part Number: 5114439AA
$95.85 MSRP: $110.00
You Save: $14.15 (13%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Rear Pads; Pad Kit Rear Disc Brake; Disc Brake Pad Set
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Brake Pads, Front Part Number: 5134358AA
$111.26
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Front Pads; Pad Kit Front Disc Brake
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Pad Kit - Rear Disc Brake Part Number: 68675615AA
$85.80 MSRP: $129.00
You Save: $43.20 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT-REAR DISC BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Front Part Number: 68526732AA
$199.59 MSRP: $299.00
You Save: $99.41 (34%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2025 Chrysler Pacifica | Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica PAD KIT-FRONT DISC BRAKE Part Number: 68675578AA
$157.49 MSRP: $232.00
You Save: $74.51 (33%)
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Pacifica | Hybrid Pinnacle, Hybrid Select, Limited, Pinnacle, Select | 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Brake Pads, Rear Part Number: 68507069AA
$257.19 MSRP: $379.00
You Save: $121.81 (33%)
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)

Chrysler Pacifica Brake Pads

Choose OEM Brake Pads that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Pads follows strict manufacturing steps to lock in quality and fit. If your Chrysler Pacifica matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Pacifica parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Brake Pads for Chrysler Pacifica generate friction which stops or slows the car by converting the car's kinetic energy into heat at the wheels. Each brake pad set consists of a metal backing plate with a friction compound that gets pressed against the rotor when clamped by the caliper. Normally, every disc will work with two Brake Pads. In the Chrysler Pacifica, wear sensors, audible indicators, assist the driver in knowing when the material is due for replacement as a result of regular driving. Wear sensors alert the driver when the lining approaches the minimum specified thickness set out by Chrysler. By consistently inspecting and replacing Brake Pads when necessary, one can ensure consistent braking response and minimize the risk of fade caused by overheating surfaces. The pads are made from different materials, non-metallic, semi-metallic, fully metallic, and ceramic, all of which provide a suitable level of friction as well as durability and operating noise. The original equipment choices on a Chrysler Pacifica are designed for day-to-day driving, but more demanding circumstances can produce additional heat that can overwhelm those Brake Pads. The proper choice of material maintains the Chrysler Pacifica braking system effectively, while worn Brake Pads replacement restores the original designed performance over various road conditions for all drivers.

Chrysler Pacifica Brake Pads Parts and Q&A

Brake Pads, Front
5134358AA
Q:
How to Service and Repair Brake Pads on the Front Wheels on Chrysler Pacifica?
A:
First, get rid of the fluid reservoir cap from the master cylinder and lift up the vehicle for servicing the front brake pads. First, remove the tire and wheel assembly, then set a C-clamp over the Brake Caliper, with the screw-drive head hitting the outside shoe and the hook placed at the rear of the caliper. Slightly tighten the valve stem by turning the valve knob cautiously to let the pistons go back and unbind the outermost brake shoe from the caliper fingers. After you've removed the outboard shoe, pull the caliper further inboard so the rotor creates some space between itself and the inboard brake shoe. Separate the brake shoe from the caliper pistons without causing any harm to either. Free the brake caliper guide pin bolts and get the caliper off of the brake adapter, then lower it by its support or hang it out of the way so as not to overstretch the brake cable. Take the brake shoes out of the disc brake caliper adapter and afterward, install the reservoir cap on the master cylinder. Placement should be done with the new brake shoes over the anti-rattle clips and you should verify proper clip installation. If required, remove the paper covering from the noise suppression gasket sticking to the outer and inner brake shoes' rear surfaces. Slide the piston back into the caliper all the way to its mounting location, watching out not to harm the caliper guide pins' boots during the process. Place the disc brake caliper over the brake shoes while they're mounted on the adapter and then tighten the upper caliper guide pin bolt to 43 Nm. After that, tighten the lower bolt to 43 Nm as well. Put the tire and wheel back in place and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), before lowering the vehicle. Press the brake pedal firmly two to three times to put the shoes on the rotor and caliper, check the brake fluid reservoir and complete a short drive to make sure the brakes are working properly.
Brake Pads, Rear
5114439AA
Q:
How to Properly Install and Service a Brake Pads on Chrysler Pacifica?
A:
Before mounting the caliper onto the knuckle, pull the caliper piston back into the caliper bore to give enough space for the pads against the rotor. Hold the inboard pad retainer clip against the piston cavity and press fiercely until it sits in the groove, so the inboard brake pad backing plate is flat on the piston. Make sure the outboard brake pads are in place and the spring clip is installed downward, after the caliper is set in. Then, fit the outboard brake pad locating pins against the end of each ramp on the caliper fingers and slide the pad onto the caliper so the fingers rest on the pads and the pins go perfectly into the holes. The shims on both the upper and lower slide abutments of the caliper adapter must be in place before joining the caliper assembly and care should be taken not to damage any parts nearby. After the caliper guide pins are retracted, clear the bosses on the caliper adapter and mount the caliper lower end first, with the outboard pad's upper edge fitting the caliper slide abutment. Fit the guide pin bolts in their caliper holes and tighten them to 23 Nm (17 ft. lbs.), then fit the tire and wheel onto the studs and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.). Reduce the car and pump the brake pedal as needed until your brake pedal feels firm, check the fluid in the reservoir and top it off when needed and then go for a drive, braking moderately many times to erase foreign materials from the brakes and make the pads fit to the disc better.