How to Install an Ignition Coil for a 3.3/3.8L Engine on Chrysler Town & Country?

First, place the ignition coil carefully over the studs on the bracket and hold it by hand, then tighten the two nuts onto the coil. After that, link the electrical connector to the ignition coil and put the ignition cables in place. Lift the power steering reservoir into place and put the bracket over the mounting stud, then attach the two bolts that fasten it to the intake manifold. Attach the lower nut to the stud on the ignition coil bracket and then secure the negative battery cable, tightly screwing the nut to 5 Nm (45 in. lbs.).

How to Service and Repair an Ignition Coil on Chrysler Town & Country?

To start any ignition coil service or repair, detach the negative battery cable beforehand. Discharge the air pressure from the throttle and speed control lines, then take out the 2 bolts at the top of the reservoir to remove it from the intake manifold. Screw the lower nut on the power steering reservoir's stud counterclockwise and then move the reservoir slightly to the left towards you. Afterward, take out the ignition cables from the ignition coil and cut off the electrical connector. Reach in and remove the nuts on the ignition coil studs and unbolt them to remove it from the coil mount. For installation, aim the new coil over the studs on the bracket and throw a bolt through each side of the coil to secure it. After fitting the 2 nuts on the ignition coil studs, tighten the nuts together with the bolts. Plug the electrical connector into the ignition coil and fit both ends of the ignition wires into the spark plugs. Moving the power steering reservoir, place the bracket onto the mounting stud and bolts into the intake manifold. Tighten the lower nut on the stud on the ignition coil bracket, place the throttle and speed control cables into their correct slot and then reconnect the negative battery cable.

OEM Chrysler Town & Country Ignition Coil

Ignition Coil Resistor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Ignition Coils found

View related parts
Chrysler Town & Country Ignition Coil Part Number: 4609140AB
$7.93 MSRP: $169.00
You Save: $161.07 (96%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil/Ignition - Ignition; Coil Ignition
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Town & Country | LX, LXi, Limited | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 56032520AF
$115.96 MSRP: $174.00
You Save: $58.04 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil/Ignition - Ignition
- Replaces: 56032520AC, 56032520AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2010 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring, Touring Plus, Walter P. Chrysler Signature Series | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 5149168AJ
$79.11 MSRP: $119.00
You Save: $39.89 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - Ignition; Direct Ignition Coil; Coil On Plug Coil; Coil Assembly; Coil Ignition
- Replaces: 5149168AI, 5149168AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 4606869AD
$83.46 MSRP: $116.00
You Save: $32.54 (29%)
ADD TO CART
Product Specifications
- Other Name: Coil/Ignition - Ignition; Direct Ignition Coil; Coil On Plug Coil; Coil
- Replaces: 4606869AC, 4606869AB, 4606869AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, Touring, Touring Plus | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 4609140AC
Product Specifications
- Other Name: Coil/Ignition - Ignition
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2000 Chrysler Town & Country | LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: MD101644
Product Specifications
- Other Name: Coil V6 Assembly Ignition; Spark Plug Wire; Can Coil; Cable Set; Coil; Coil, Ignition
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: MD141044
Product Specifications
- Other Name: Coil/Ignition - Ignition; Coil, 4-Cylinder, 2.2 TBI-2.5 Turbo, (Insulator 4638991); Optional W/5234610 Toyodenso.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 4443971
Product Specifications
- Other Name: Coil/Ignition - Ignition; Coil, 4-Cylinder, 2.2 TBI-2.5 Turbo, (Insulator 4638991); Ignition Coil options available.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1999 Chrysler Town & Country | Base, LX, LXi, Limited, SX | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Ignition Coil Part Number: 4176009
Product Specifications
- Other Name: Coil - Ignition Assembly; Can Coil; Coil; Wiring, Front End (Headlamp To Instrument.Panel); Ignition Coils for 2.2 & 2.6 Engines.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1991, 1984-1988 Chrysler Town & Country | Base, Mark Cross | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS

Chrysler Town & Country Ignition Coil

Choose OEM Ignition Coil that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Ignition Coil follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Ignition Coil is used in Chrysler Town & Country vehicles, and works to steps up the small voltage from the battery to the level required to fire the air/fuel combination in the cylinders. This component can be considered as the interface between the primary and secondary circuits, while the primary circuit involves the battery, the switch and the triggering device and the secondary circuit implies the presence of high tension lead, distributor cap and spark plug wires. Periodically, Chrysler Town & Country vehicles have incorporated multiple kinds of ignition coils, ranging from the breaker point or electronic distributor ignition systems; the coil-on-plug systems; as well as the wasted spark systems. These coils are used to create the right voltage that is needed for making sparks and thus, right engine performances.

Chrysler Town & Country Ignition Coil Parts and Q&A

Ignition Coil
4606869AD
Q: How to Install an Ignition Coil for a 3.3/3.8L Engine on Chrysler Town & Country?
A:
First, place the ignition coil carefully over the studs on the bracket and hold it by hand, then tighten the two nuts onto the coil. After that, link the electrical connector to the ignition coil and put the ignition cables in place. Lift the Power Steering Reservoir into place and put the bracket over the mounting stud, then attach the two bolts that fasten it to the Intake Manifold. Attach the lower nut to the stud on the ignition coil bracket and then secure the negative battery cable, tightly screwing the nut to 5 Nm (45 in. lbs.).
Ignition Coil
56032520AF
Q: How to Service and Repair an Ignition Coil on Chrysler Town & Country?
A:
To start any ignition coil service or repair, detach the negative battery cable beforehand. Discharge the air pressure from the throttle and speed control lines, then take out the 2 bolts at the top of the reservoir to remove it from the Intake Manifold. Screw the lower nut on the Power Steering Reservoir's stud counterclockwise and then move the reservoir slightly to the left towards you. Afterward, take out the ignition cables from the ignition coil and cut off the electrical connector. Reach in and remove the nuts on the ignition coil studs and unbolt them to remove it from the coil mount. For installation, aim the new coil over the studs on the bracket and throw a bolt through each side of the coil to secure it. After fitting the 2 nuts on the ignition coil studs, tighten the nuts together with the bolts. Plug the electrical connector into the ignition coil and fit both ends of the ignition wires into the spark plugs. Moving the power steering reservoir, place the bracket onto the mounting stud and bolts into the intake manifold. Tighten the lower nut on the stud on the ignition coil bracket, place the throttle and speed control cables into their correct slot and then reconnect the negative battery cable.