How to Service and Repair a Brake Light Switch on Dodge Caliber?

The first step to servicing the brake light switch is to take off the negative cable from the battery before anything else. When the vehicle has one, take out the silencer pad fixed just below the steering column. Unplug the connector at the switch by disconnecting wire harness (4). Pull the stop lamp switch backward after rotating it counterclockwise about 30 degrees. The stop lamp switch should be thrown away and should not be used again.

How to Install a Brake Light Switch on Dodge Caliber?

When installing the stop lamp switch you'll need to hold the switch in one hand, use the other hand to pull outward on the plunger to move it to its fully extended position and allow it to ratchet out completely. Then join the wiring harness connector (1) to the stop lamp switch (2). Push the brake pedal all the way down and line up the index key in the switch with the notch in the square mounting hole in the bracket (6) and then mount the stop lamp switch into the bracket. Rotate the switch clockwise, until it is about 30 degrees if it isn't already that far, then continue to rotate it clockwise slightly to pull up on the switch and has it fully seated. Be careful not to use too much force when pulling back on the brake pedal as this might do damage to the stop lamp switch or striker. Pull back on the brake pedal gently until it stops moving: this releases the switch plunger back to its correct position. Finally flick on the brights, check the brake lamps and speed control.

OEM Dodge Caliber Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Brake Light Switches found

View related parts
Dodge Caliber Lamp Switch Part Number: 56054001AD
$37.64 MSRP: $54.10
You Save: $16.46 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch - Stop Lamp; Brake Light Switch; Stoplamp Switch; Switch; Switch Stop Lamp
- Replaces: 56054001AB, 56054001AC, 56054001AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Switch Package - Stop Lamp Part Number: 5083344AB
Product Specifications
- Other Name: SW PKG-STOP LAMP
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Caliber | R/T, SE, SRT-4, SXT | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS

Dodge Caliber Brake Light Switch

Choose OEM Brake Light Switch that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Light Switch follows strict manufacturing steps to lock in quality and fit. If your Dodge Caliber matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Caliber parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Brake Light Switch is a part that improves and stabilizes the operation of the Dodge Caliber, a C1 hatchback model manufactured within the years 2007-2012. This critical switch causes the brake light to switch on once the brake pedal is pressed and this goes a long way in informing other motorists on the status of the Dodge Caliber, that is slowing down or coming to a standstill hence enhancing the safety of the road. Brake Light Switch is suitable for different Caliber vehicles and is suitable for the SE and SXT models mainly. The Design and specification of each model of the Brake Light Switch has been done in such a way that the performance and reliability is never compromised hence improving the overall performance of the Dodge Caliber. For instance, the Dodge Caliber has been highlighted in regards to safety features; it has earned decent scores from Insurance Institute for Highway Safety. This safety profile significantly centrally features the Brake Light Switch because it is through its utilization that other users of the road are informed of the vehicle's intentions. Also, considering that the Brake Light Switch is an automotive application, its construction is very robust which places it at a vantage point in the market. The exterior and interior design as well as the features associated with it also serve to exaggerate the reliability and durability that is expected out of a Dodge Caliber. To sum up, the Brake Light Switch is an essential component, which highlights the safety and performance significance of the Dodge Caliber automobiles.

Dodge Caliber Brake Light Switch Parts and Q&A

Switch Package - Stop Lamp
5083344AB
Q: How to Service and Repair a Brake Light Switch on Dodge Caliber?
A:
The first step to servicing the brake light switch is to take off the negative cable from the battery before anything else. When the vehicle has one, take out the silencer pad fixed just below the steering column. Unplug the connector at the switch by disconnecting wire harness (4). Pull the stop lamp switch backward after rotating it counterclockwise about 30 degrees. The stop lamp switch should be thrown away and should not be used again.
Lamp Switch
56054001AD
Q: How to Install a Brake Light Switch on Dodge Caliber?
A:
When installing the stop lamp switch you'll need to hold the switch in one hand, use the other hand to pull outward on the plunger to move it to its fully extended position and allow it to ratchet out completely. Then join the wiring harness connector (1) to the stop lamp switch (2). Push the brake pedal all the way down and line up the index key in the switch with the notch in the square mounting hole in the bracket (6) and then mount the stop lamp switch into the bracket. Rotate the switch clockwise, until it is about 30 degrees if it isn't already that far, then continue to rotate it clockwise slightly to pull up on the switch and has it fully seated. Be careful not to use too much force when pulling back on the brake pedal as this might do damage to the stop lamp switch or striker. Pull back on the brake pedal gently until it stops moving: this releases the switch plunger back to its correct position. Finally flick on the brights, check the brake lamps and speed control.