How to Safely and Correctly Install an Air Bag Control Module on Dodge Charger?

Before installing the ORC, first make sure the air bags do not activate by turning off the SRS, disconnecting the car's negative battery cable and letting the system's capacitor completely discharge for two whole minutes. Make sure to properly manage the ORC to prevent accidents that may result in a broken impact sensor; if you drop it, the unit needs to be replaced. After setting the ORC into the main switch, place it on the welded bracket on the top of the floor panel transmission tunnel so that the arrow on the label points forward and the pins slide into the mounting holes. Use three screws to connect the ORC to the bracket and tighten them to 11 Nm (97 in. lbs.), then put back the sound deadening material on the ORC. Attach the two wire harnesses on the ORC connector receptacles and make sure the latches are fully secured. At the end, place the center floor console inside the transmission tunnel, but do not attach the battery negative cable until the whole SRS system has been checked following service to any SRS part.

How to Service an Air Bag Control Module on Dodge Charger?

Before you touch the Occupant Restraint Controller (ORC), turn off the Supplemental Restraint System (SRS) by detaching and isolating the negative battery cable and then wait for the system capacitor to discharge for two minutes. Not striking or dropping the ORC is very important, since this can destroy the impact sensor and alter calibration settings; dropping the ORC means it must be swapped for a new one. The first step is to take out the center console in the floor panel transmission tunnel. Following this, separate the wire harness connectors from the ORC connector receptacles found on the module's rearward side. As you remove the sound deadening from the S-Hoe's top floor panel transmission tunnel, you will see the three ORC fastener screws. Once you have bunched the ORC in the front, raise it enough so that the locating pins can be released and the ORC is freed from the bracket.

OEM Dodge Charger Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Air Bag Control Modules found

View related parts
Dodge Charger Control Module Part Number: 68371748AA
$435.37 MSRP: $657.00
You Save: $221.63 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module; Module Occupant Restraint
- Replaces: 68226173AC, 68226173AD, 68226173AE, 68316744AB, 68297875AA, 68316744AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona, GT, GT Plus, R/T, R/T Road & Track, SE, SXT, SXT Plus | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Occupant Module Part Number: 56043195BB
$242.76 MSRP: $307.74
You Save: $64.98 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module; Module; Module Occupant Classification
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 56054077AK
$286.20 MSRP: $436.00
You Save: $149.80 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module
- Replaces: 56054077AH, 56054077AJ, 56054077AG, 56054077AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT, SXT Plus | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 56038943AH
$286.20 MSRP: $436.00
You Save: $149.80 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module
- Replaces: 56038943AG, 56038943AF, 56038943AE, 56038943AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Dodge Charger | Daytona, Daytona 392, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SXT | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68371749AA
$485.10 MSRP: $732.00
You Save: $246.90 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module; Module Occupant Restraint
- Replaces: 68316745AB, 68226172AC, 68297876AA, 68226172AB, 68226172AD, 68316745AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Pursuit | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Control Module Part Number: 68530280AA
$638.69 MSRP: $963.00
You Save: $324.31 (34%)
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module
- Replaces: 68226174AF, 68371750AA, 68226174AD, 68226174AE, 68297877AA, 68494626AA, 68316746AA, 68316746AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona 392, R/T 392, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 6.2L V8, 6.4L V8, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module, Passenger Side Part Number: 56043195AZ
$381.81 MSRP: $555.00
You Save: $173.19 (32%)
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module, Right; SDM Module; Diagnostic Module; Passenger Sensor; Occupant Module; Module; Module Occupant Classification
- Position: Passenger Side
- Replaces: 56043195AX, 56043195AS, 56043195AR, 56043195AT, 56043195AP
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Diagnostic Unit Part Number: 68001372AB
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Occupant Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Diagnostic Unit Part Number: 68001371AB
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Occupant Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger SDM Module Part Number: 4896097AG
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Occupant Module; Module Occupant Restraint
- Replaces: 4896097AD, 4896097AC, 4896097AF, 4896097AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger SDM Module Part Number: 4896098AH
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Occupant Module
- Replaces: 4896098AC, 4896098AE, 4896098AF, 4896098AD, 4896098AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger SDM Module Part Number: 5081041AG
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Occupant Module; Module Occupant Restraint
- Replaces: 5081041AE, 5081041AC, 5081041AD, 5081041AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger SDM Module Part Number: 5081042AG
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Occupant Module; Module Occupant Restraint
- Replaces: 5081042AF, 5081042AE, 5081042AD, 5081042AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS

Dodge Charger Air Bag Control Module

Choose OEM Air Bag Control Module that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Air Bag Control Module follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Charger Air Bag Control Module Parts and Q&A

SDM Module
4896098AH
Q:
How to Safely and Correctly Install an Air Bag Control Module on Dodge Charger?
A:
Before installing the ORC, first make sure the air bags do not activate by turning off the SRS, disconnecting the car's negative Battery Cable and letting the system's capacitor completely discharge for two whole minutes. Make sure to properly manage the ORC to prevent accidents that may result in a broken impact sensor; if you drop it, the unit needs to be replaced. After setting the ORC into the main switch, place it on the welded bracket on the top of the floor panel transmission tunnel so that the arrow on the label points forward and the pins slide into the mounting holes. Use three screws to connect the ORC to the bracket and tighten them to 11 Nm (97 in. lbs.), then put back the sound deadening material on the ORC. Attach the two wire harnesses on the ORC connector receptacles and make sure the latches are fully secured. At the end, place the center floor console inside the transmission tunnel, but do not attach the battery negative cable until the whole SRS system has been checked following service to any SRS part.
SDM Module
4896097AG
Q:
How to Service an Air Bag Control Module on Dodge Charger?
A:
Before you touch the Occupant Restraint Controller (ORC), turn off the Supplemental Restraint System (SRS) by detaching and isolating the negative Battery Cable and then wait for the system capacitor to discharge for two minutes. Not striking or dropping the ORC is very important, since this can destroy the impact sensor and alter calibration settings; dropping the ORC means it must be swapped for a new one. The first step is to take out the Center Console in the floor panel transmission tunnel. Following this, separate the wire harness connectors from the ORC connector receptacles found on the module's rearward side. As you remove the sound deadening from the S-Hoe's top floor panel transmission tunnel, you will see the three ORC fastener screws. Once you have bunched the ORC in the front, raise it enough so that the locating pins can be released and the ORC is freed from the bracket.