How to Remove and Replace Exhaust Valve and Intake Valves on Dodge Dakota?

Before you remove and replace the intake and exhaust valves, take out the negative battery cable and the cylinder head covers. After that, get the rocker arms and lash adjusters free, then remove both camshaft bearing caps and the camshaft. After that, remove the cylinder heads. Take advantage of Tool C-3422-D or C-3422-C Valve Spring Compressor and Tool 8519 Adapter to compress the valve spring and tap the upper end of the spring if needed to get the retainers to release. Remove the two spring retainer lock halves and next, the valve spring compressor. Remove the spring retainer and spring afterward and ensure there are no sharp edges in the grooves on the keepers, plus any burrs on the valve stem before you take the valve from the cylinder head. Take off the valve stem seal and note the correct position for the valve during installation. Each time you take out the valve springs, monitor them for any damage and make sure to use a spring tester for the valve to check for correct spring height and strength while the valve is open and closed. Change any springs that do not fall within standard requirements.

What Are the Key Differences Between Exhaust Valve and Intake Valve Installation on Dodge Dakota?

Start the installation by reaching into the cylinder head and putting engine oil on the stem of the valve before inserting it. Next, put in the valve stem seal (3), push it down to make it completely seat and verify that the garter spring at the top is not damaged. After that, install the spring and the spring retainer (2). Press the spring (6) down with the valve spring compressor and attach the two valve spring retainer halves (1). Once you release the compressor, make sure that the two spring retainer halves and the spring retainer have been fully seated. Put drops of clean engine oil on the camshaft journals, at 11 o'clock put the sprocket dowel for the left camshaft and at 12 o'clock put the dowel for the right camshaft and finally place the camshaft bearing caps in place. Tighten the camshaft bearing cap retaining bolts to 11 Nm (100 in. lbs.), tightening each one in 1/2 turns in the proper order. After that, set up the hydraulic lash adjusters and rocker arms.

OEM Dodge Dakota Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Intake Valves found

View related parts
Dodge Dakota Intake Valve Part Number: 53020747AB
$46.65 MSRP: $94.55
You Save: $47.90 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard 3 Per Cylinder Head; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2010 Dodge Dakota | Base, Big Horn, Laramie, Lone Star, SLT, SLT Plus, ST, SXT, Sport, Sport Plus, TRX, TRX4 | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Dakota Intake Valve Part Number: 53010512AA
$22.22 MSRP: $39.05
You Save: $16.83 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2002 Dodge Dakota | Base, SLT, Sport | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Intake Valve Part Number: 53006723
$19.33 MSRP: $24.50
You Save: $5.17 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard; Valve, Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2003 Dodge Dakota | Base, LE, R/T, S, SLT, SXT, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Intake Valve Part Number: 4298137
$14.79 MSRP: $17.00
You Save: $2.21 (13%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake Standard; Valves; Intake Standard W/Ede Carbureted or Edj High-Performance Engine.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1995 Dodge Dakota | Base, LE, S, SE, SLT, Sport, WS | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Intake Valve Part Number: 53021990AA
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Dakota | Big Horn, Laramie, Lone Star, SLT, SXT, Sport, TRX, TRX4 | 8 Cyl 4.7 L FLEX
View related parts
Dodge Dakota Intake Valve Part Number: 33003515
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard; Valve, Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-1999 Dodge Dakota | Base, SLT, Sport, WS | 4 Cyl 2.5 L GAS

Dodge Dakota Intake Valve

Choose OEM Intake Valve that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Intake Valve follows strict manufacturing steps to lock in quality and fit. If your Dodge Dakota matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Dakota parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Dakota Intake Valve is one of the most important, and efficient parts that helps to boost up the performance and the reliability of Dodge vehicles more specifically the Dodge Dakota kudos to this product. The Intake Valve is famous for controlling the blasting of air and fuel to the cylinders with precision in the right combination to produce the maximum power of the engines and efficiency in combustion. This is especially true for the various Dakota models, since a properly working Intake Valve eliminates problems leading to decline in its performance and expensive replacement. The Dodge Dakota manufactured between 1986 and 2010 is a powerful vehicle with an unmistakable design, which turns it into a real favorite of the truck category. It is possible to conclude that the Intake Valve compatibility with a variety of the Dakota models helps the drivers to keep their vehicles in good working condition and safe. Thus, maintenance of the Intake Valve and the replacement of the same is done on a regular basis to prevent any breakdown of the engines and to increase the life of the same. Significantly, in the automotive field, Dodge Dakota Intake Valve is one of the key areas that distinguished for excellent workmanship and its ability to work for long time without giving out thus increasing more reliability of the vehicle. The durability of this Intake Valve is impressive and tailored for daily use and high traffic situations which characterizes car's production under the Dodge brand. In conclusion, therefore, the Dodge Dakota Intake Valve is one of the most crucial components when it comes to the general performance, safety, and competence of the Dodge Dakota cars; thus its popularity among the drivers, who appreciate strength and reliability in their automobiles.

Dodge Dakota Intake Valve Parts and Q&A

Intake Valve
53021990AA
Q: How to Remove and Replace Exhaust Valve and Intake Valves on Dodge Dakota?
A:
Before you remove and replace the intake and exhaust valves, take out the negative Battery Cable and the cylinder head covers. After that, get the Rocker Arms and Lash Adjusters free, then remove both Camshaft bearing caps and the camshaft. After that, remove the cylinder heads. Take advantage of Tool C-3422-D or C-3422-C Valve Spring Compressor and Tool 8519 Adapter to compress the valve spring and tap the upper end of the spring if needed to get the retainers to release. Remove the two spring retainer lock halves and next, the valve spring compressor. Remove the spring retainer and spring afterward and ensure there are no sharp edges in the grooves on the keepers, plus any burrs on the valve stem before you take the valve from the cylinder head. Take off the Valve Stem Seal and note the correct position for the valve during installation. Each time you take out the valve springs, monitor them for any damage and make sure to use a spring tester for the valve to check for correct spring height and strength while the valve is open and closed. Change any springs that do not fall within standard requirements.
Intake Valve
53020747AB
Q: What Are the Key Differences Between Exhaust Valve and Intake Valve Installation on Dodge Dakota?
A:
Start the installation by reaching into the cylinder head and putting engine oil on the stem of the valve before inserting it. Next, put in the Valve Stem Seal (3), push it down to make it completely seat and verify that the garter spring at the top is not damaged. After that, install the spring and the spring retainer (2). Press the spring (6) down with the valve spring compressor and attach the two valve spring retainer halves (1). Once you release the compressor, make sure that the two spring retainer halves and the spring retainer have been fully seated. Put drops of clean engine oil on the Camshaft journals, at 11 o'clock put the sprocket dowel for the left camshaft and at 12 o'clock put the dowel for the right camshaft and finally place the camshaft bearing caps in place. Tighten the camshaft bearing cap retaining bolts to 11 Nm (100 in. lbs.), tightening each one in 1/2 turns in the proper order. After that, set up the hydraulic Lash Adjusters and Rocker Arms.